TY - JOUR A1 - Askar, Enis A1 - Kauffeld, M. A1 - Maurath, T. A1 - Germanus, J. T1 - N2O/CO2-mixtures as refrigerants for temperatures below -50 °C JF - International Journal of Refrigeration N2 - The EU F-Gas Regulation grants exceptions from the GWP-related placing on the market prohibition for stationary refrigeration equipment for applications below -50 °C. Nonetheless, non-flammable refrigerants, which can be used for that temperature range, become increasingly expensive and rare inside the EU due to the phase down of HFCs under the regulation. Flammable alternatives based on methane, ethane and ethylene are available, but are not viable for all applications due to their flammability. Carbon dioxide cannot be used for applications below -50 °C due to CO 2 ’s triple point at -56 °C. Nitrous oxide with a triple point at -92 °C seems to be an alternative. However, possible exothermal decomposition of N 2 O calls for additional measures in order to be able to operate such systems safely. Two low-temperature systems have been developed, built and successfully operated at evaporation temperatures down to - 80 °C with mixtures of N 2 O and CO 2 and different lubricants at ILK and Karlsruhe University of Applied Sciences. The units achieved similar energy efficiency as the standard HFC-equipment used for freeze drying. Possible decomposition of N 2 O could successfully be supressed by various measures. KW - Carbon dioxide KW - Freeze-dryer KW - Low temperature KW - Nitrous oxide KW - Safety measures PY - 2020 DO - https://doi.org/10.1016/j.ijrefrig.2020.04.026 SN - 0140-7007 VL - 117 SP - 316 EP - 327 PB - Elsevier Ltd. AN - OPUS4-50946 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Jaunich, Matthias A1 - Wolff, Dietmar T1 - Influence of gamma irradiation on low temperature properties of rubber seal materials JF - Kautschuk, Gummi, Kunststoffe (KGK) N2 - In many fields the function of seal materials is required at low temperatures. Therefore the understanding of failure mechanisms at low temperatures is of high importance. In some applications elastomeric seals are used in environments with increased irradiation backgrounds, as e.g. in containers for radioactive waste. This paper reports on the influence of gamma irradiation on the low temperature properties of different fluorocarbon rubber (FKM) materials. The samples were irradiated with gamma doses of up to 600 kGy and the induced changes of material properties were tested by methods sensitive to the rubber-glass transition, like DSC and DMA. Additionally, compression set measurements were performed to give information about recovery behaviour at low temperatures. KW - Seal KW - O-ring KW - Low temperature KW - Gamma irradiation KW - Compression set KW - Dichtungen KW - O-Ringe KW - Tiefe Temperatur KW - Gamma-Bestrahlung KW - Druckverformungsrest PY - 2015 SN - 0948-3276 SN - 0022-9520 VL - 68 IS - 6 SP - 85 EP - 89 PB - Hüthig CY - Heidelberg AN - OPUS4-33552 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Jaunich, Matthias A1 - Wolff, Dietmar A1 - Stark, Wolfgang T1 - Low temperature properties of rubber seals - Results of component tests - JF - Kautschuk, Gummi, Kunststoffe (KGK) N2 - Rubbers are widely used as sealing material in various applications. In many fieldsthefunction of seal materials at lowtemperatures is required. Therefore the understanding of faiiure mechanisms that lead to leakage at low temperatures is of high importance. Therefore the lower Operation temperature limit of rubber seals should be determined in dependence of the material properties. The results of Differential Scanning Calorimetry (DSC) and Dynamic Mechanical Analysis (DMA) are combined with results of standardized measurements as the compression set according to ISO 815. To reduce the test time of the Standard tests a faster and more efficient technique was developed and applied. In addition the breakdown temperature of the sealing function of O-ring seals at lowtemperatures is measured in a component test Setup in dependence of the material and the degree of compression. KW - Seal KW - O-ring KW - Low temperature KW - Component test KW - Compression set KW - Dichtungen KW - O-Ringe KW - Tiefe Temperatur KW - Bauteilversuche KW - Druckverformungsrest PY - 2013 SN - 0948-3276 SN - 0022-9520 VL - 66 IS - 7-8 SP - 26 EP - 30 PB - Hüthig CY - Heidelberg AN - OPUS4-28894 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Kromm, Arne A1 - Dixneit, Jonny A1 - Kannengießer, Thomas T1 - Residual stress engineering by low transformation temperature alloys - state of the art and recent developments JF - Welding in the world N2 - Residual stress engineering in welding becomes more and more prominent as the use of tailored materials, e.g., high-strength steels, calls for maximum utilization of the material properties. As a consequence, residual stresses have to be considered as design criterion. Moreover, it may be utilized to improve the material's performance. Low transformation temperature alloys are a smart approach to control the residual stresses already during the welding process avoiding time-consuming postweld treatments. This paper gives an overview about the progress made in research in this topic with special focus on residual stresses. Basics as well as important developments will be addressed. KW - Residual stresses KW - Martensite KW - Low temperature KW - Transformation PY - 2014 DO - https://doi.org/10.1007/s40194-014-0155-6 SN - 0043-2288 SN - 1878-6669 VL - 58 IS - 5 SP - 729 EP - 741 PB - Springer CY - Oxford AN - OPUS4-31446 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Kromm, Arne A1 - Kannengießer, Thomas A1 - Gibmeier, J. A1 - Genzel, C. A1 - Van der Mee, V. T1 - Determination of residual stresses in low transformation temperature (LTT -) welds metals using X-rayand high energy synchrotron radiation JF - Welding in the world N2 - Crack and fatigue resistance are relevant evaluation criteria for welded joints and are decreased by tensile residual stresses resulting from the welding and cooling process, while compressive residual stresses can have a positive influence on the characteristics mentioned. In order to generate compressive residual stresses, a set of post weld treatment procedures is available, like shot peening, hammering, etc. These procedures have the disadvantage that they are time and cost extensive and have to be applied after welding. As another point, such technologies can only produce compressive stresses at the top surface, i.e. can only contribute to the reduction of the risk of cracks initiated at the surface, like fatigue cracks. A chance to generate compressive stresses over the complete weld joint during the welding procedure is offered by the so-called Low Transformation Temperature (LTT -) filler wires. Compared to conventional wires, these materials show lower phase transformation temperatures, which can work against coolingrelated tensile stresses, resulting from respective shrinkage restraint. In consequence, distinct compressive residual stresses can be observed within the weld and adjacent areas. The strength of these fillers makes them potentially applicable to high-strength steel welding. Welds produced with different LTT – filler wires have shown different levels and distributions of the resulting residual stresses depending on the specific transformation temperature. The transformation temperatures are determined by temperature measurement. Classical X-ray diffraction as well as diffraction methods using high energy synchrotron radiation have been used for residual stress analysis. By means of high energy synchrotron diffraction in reflection mode residual stress depth gradients can be determined nondestructively. The phase selective nature of the diffraction measurements enables the simultaneous determination of the phase specific residual stresses of all contributing crystalline phases within one experiment. The application of white beam diffraction implies recording of a multitude of diffraction lines within the energy range of the provided energy spectrum of the white beam. By this means phase specific residual stress depth distributions up to distances of 150 ìm below the surface can be analysed for steel using the energy dispersive set-up of the HMI-beamline EDDI at the Bessy site, Berlin, providing an energy range between 20-150 keV. As a side effect quantitative phase analysis can be carried out using white energy dispersive diffraction e.g. the determination of the content of retained austenite in the weld. KW - Filler materials KW - Low temperature KW - Reference lists KW - Residual stresses KW - Temperature KW - Transformation KW - Synchrotron radiation KW - Phase specific residual stresses KW - Energy dispersive diffraction PY - 2009 SN - 0043-2288 SN - 1878-6669 VL - 53 IS - 1/2 SP - 3 EP - 16 PB - Springer CY - Oxford AN - OPUS4-19214 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Mieller, Björn A1 - Rabe, Torsten A1 - Rangelov, V. T1 - In situ shrinkage measurement during pressure-assisted sintering of low temperature co-fired ceramic panels JF - International Journal of Applied Ceramic Technology N2 - Shrinkage measurements of miniaturized low temperature co-fired ceramics (LTCC) samples under load typically lead to collapsing of the samples, which hampers the characterization of shrinkage up to full densification. In this paper, a measurement setup is presented, which allows for in situ shrinkage measurements of practical, large LTCC panels during pressure-assisted sintering in a sintering press. The shrinkage behavior of two commercial LTCC systems (GreenTape 951 and Ceramtape GC) has been measured under loads of up to 1 MPa. No crushing of the specimens was observed and reproducible characterization of shrinkage up to full densification has been performed. Based on comparisons to thermomechanical analyzer measurements in this and other studies, it was found that the in situ approach is much better suited for shrinkage characterization of LTCC under load. Reproducibility and accuracy of the method are discussed and practical as well as more academic applications are proposed. KW - Shrinkage KW - Low temperature KW - Sinter/sintering PY - 2017 DO - https://doi.org/10.1111/ijac.12634 SN - 1546-542X SN - 1744-7402 VL - 14 IS - 2 SP - 245 EP - 251 AN - OPUS4-39327 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -