<?xml version="1.0" encoding="utf-8"?>
<export-example>
  <doc>
    <id>65213</id>
    <completedYear/>
    <publishedYear>2025</publishedYear>
    <thesisYearAccepted/>
    <language>eng</language>
    <pageFirst>9726</pageFirst>
    <pageLast>9737</pageLast>
    <pageNumber/>
    <edition/>
    <issue>12</issue>
    <volume>77</volume>
    <type>article</type>
    <publisherName>Springer Nature</publisherName>
    <publisherPlace/>
    <creatingCorporation/>
    <contributingCorporation/>
    <belongsToBibliography>1</belongsToBibliography>
    <completedDate>--</completedDate>
    <publishedDate>--</publishedDate>
    <thesisDateAccepted>--</thesisDateAccepted>
    <title language="eng">Resolving the Subsurface Residual Stress Maximum in Laser Powder Bed-Fused 316L Stainless Steel by Diffraction-Based Analysis</title>
    <abstract language="eng">Laser powder bed fusion (PBF-LB/M) is a metal additive manufacturing process. Due to the complex nature of the layer-wise, repeated heating and cooling cycles, it tends to generate high-magnitude residual stresses. If not correctly understood and mitigated through in- or post-process approaches, these residual stresses can be detrimental as they are often tensile at the surface. However, determining the magnitude and location of peak tensile residual stresses is not trivial as they are often located subsurface. This work focuses on determining the magnitude and location of these deleterious tensile residual stresses in a PBF-LB/316L specimen. Two diffraction-based Methods are used to reveal the relationship between the residual stresses and the underlying microstructure. On the one hand, high spatial resolution Neutron diffraction is used to determine triaxial stresses from the bulk to a depth of 0.15 mm. On the other hand, laboratory X-ray diffraction coupled with electrolytical layer removal allows the biaxial residual stress depth profile to be probed from the surface to a depth of about 0.6 mm. The results show a good agreement between the two methods. The peak residual stress is shown to be 500 MPa, which appears as a plateau between 0.08 and 0.35 mm in depth.</abstract>
    <parentTitle language="eng">JOM - The Journal of The Minerals, Metals &amp; Materials Society (TMS)</parentTitle>
    <identifier type="doi">10.1007/s11837-025-07719-y</identifier>
    <identifier type="issn">1543-1851</identifier>
    <identifier type="urn">urn:nbn:de:kobv:b43-652138</identifier>
    <enrichment key="opus.source">publish</enrichment>
    <enrichment key="date_peer_review">22.12.2025</enrichment>
    <enrichment key="opus.doi.autoCreate">false</enrichment>
    <enrichment key="opus.urn.autoCreate">true</enrichment>
    <licence>Creative Commons - CC BY - Namensnennung 4.0 International</licence>
    <author>Alexander Evans</author>
    <author>Jakob Schröder</author>
    <author>T. Pirling</author>
    <author>Alexander Ulbricht</author>
    <author>Patricia Suárez Ocaño</author>
    <author>Giovanni Bruno</author>
    <subject>
      <language>eng</language>
      <type>uncontrolled</type>
      <value>Residual stress</value>
    </subject>
    <subject>
      <language>eng</language>
      <type>uncontrolled</type>
      <value>Diffraction</value>
    </subject>
    <subject>
      <language>eng</language>
      <type>uncontrolled</type>
      <value>Laser Powder Bed Fusion</value>
    </subject>
    <subject>
      <language>eng</language>
      <type>uncontrolled</type>
      <value>316L</value>
    </subject>
    <subject>
      <language>eng</language>
      <type>uncontrolled</type>
      <value>Additive manufacturing</value>
    </subject>
    <subject>
      <language>eng</language>
      <type>uncontrolled</type>
      <value>Microstructure</value>
    </subject>
    <subject>
      <language>eng</language>
      <type>uncontrolled</type>
      <value>AGIL</value>
    </subject>
    <collection role="ddc" number="620">Ingenieurwissenschaften und zugeordnete Tätigkeiten</collection>
    <collection role="institutes" number="">5 Werkstofftechnik</collection>
    <collection role="institutes" number="">5.2 Metallische Hochtemperaturwerkstoffe</collection>
    <collection role="institutes" number="">8 Zerstörungsfreie Prüfung</collection>
    <collection role="institutes" number="">8.5 Röntgenbildgebung</collection>
    <collection role="themenfelder" number="">Material</collection>
    <collection role="literaturgattung" number="">Verlagsliteratur</collection>
    <collection role="fulltextaccess" number="">Datei für die Öffentlichkeit verfügbar ("Open Access")</collection>
    <collection role="unnumberedseries" number="">Wissenschaftliche Artikel der BAM</collection>
    <collection role="themenfelder" number="">Additive Fertigung</collection>
    <thesisPublisher>Bundesanstalt für Materialforschung und -prüfung (BAM)</thesisPublisher>
    <file>https://opus4.kobv.de/opus4-bam/files/65213/Evans_JOM_2025.pdf</file>
  </doc>
  <doc>
    <id>51171</id>
    <completedYear/>
    <publishedYear>2021</publishedYear>
    <thesisYearAccepted/>
    <language>eng</language>
    <pageFirst>140154</pageFirst>
    <pageLast/>
    <pageNumber/>
    <edition/>
    <issue/>
    <volume>799</volume>
    <type>article</type>
    <publisherName>Elsevier B.V.</publisherName>
    <publisherPlace/>
    <creatingCorporation/>
    <contributingCorporation/>
    <belongsToBibliography>1</belongsToBibliography>
    <completedDate>--</completedDate>
    <publishedDate>--</publishedDate>
    <thesisDateAccepted>--</thesisDateAccepted>
    <title language="eng">Mechanical anisotropy of additively manufactured stainless steel 316L: An experimental and numerical study</title>
    <abstract language="eng">The underlying cause of mechanical anisotropy in additively manufactured (AM) parts is not yet fully understood and has been attributed to several different factors like microstructural defects, residual stresses, melt pool boundaries, crystallographic and morphological textures. To better understand the main contributing factor to the mechanical anisotropy of AM stainless steel 316L, bulk specimens were fabricated via laser powder bed fusion (LPBF). Tensile specimens were machined from these AM bulk materials for three different inclinations: 0◦, 45◦, and 90◦ relative to the build plate. Dynamic Young’s modulus measurements and tensile tests were used to determine the mechanical anisotropy. Some tensile specimens were also subjected to residual stress measurement via neutron diffraction, porosity determination with X-ray micro-computed tomography (μCT), and texture analysis with electron backscatter diffraction (EBSD). These investigations revealed that the specimens exhibited near full density and the detected defects were spherical. Furthermore, the residual stresses in the loading direction were between −74 ± 24 MPa and 137 ± 20 MPa, and the EBSD measurements showed a preferential ⟨110⟩ orientation parallel to the build direction. A crystal plasticity model was used to analyze the elastic anisotropy and the anisotropic yield behavior of the AM specimens, and it was able to capture and predict the experimental behavior accurately. Overall, it was shown that the mechanical anisotropy of the tested specimens was mainly influenced by the crystallographic texture.</abstract>
    <parentTitle language="eng">Materials Science and Engineering: A</parentTitle>
    <identifier type="doi">10.1016/j.msea.2020.140154</identifier>
    <identifier type="issn">0921-5093</identifier>
    <identifier type="urn">urn:nbn:de:kobv:b43-511719</identifier>
    <enrichment key="date_peer_review">26.11.2020</enrichment>
    <licence>Creative Commons - CC BY - Namensnennung 4.0 International</licence>
    <author>Amir Charmi</author>
    <author>Rainer Falkenberg</author>
    <author>Luis Ávila Calderón</author>
    <author>Gunther Mohr</author>
    <author>Konstantin Sommer</author>
    <author>Alexander Ulbricht</author>
    <author>Maximilian Sprengel</author>
    <author>Romeo Saliwan Neumann</author>
    <author>Alexander Evans</author>
    <author>Birgit Skrotzki</author>
    <subject>
      <language>eng</language>
      <type>uncontrolled</type>
      <value>Mechanical anisotropy</value>
    </subject>
    <subject>
      <language>eng</language>
      <type>uncontrolled</type>
      <value>Residual stress</value>
    </subject>
    <subject>
      <language>eng</language>
      <type>uncontrolled</type>
      <value>Crystal plasticity</value>
    </subject>
    <subject>
      <language>eng</language>
      <type>uncontrolled</type>
      <value>Selective laser melting (SLM)</value>
    </subject>
    <subject>
      <language>eng</language>
      <type>uncontrolled</type>
      <value>Laser beam melting (LBM)</value>
    </subject>
    <collection role="ddc" number="620">Ingenieurwissenschaften und zugeordnete Tätigkeiten</collection>
    <collection role="institutes" number="">5 Werkstofftechnik</collection>
    <collection role="institutes" number="">5.1 Mikrostruktur Design und Degradation</collection>
    <collection role="institutes" number="">5.2 Metallische Hochtemperaturwerkstoffe</collection>
    <collection role="institutes" number="">5.5 Materialmodellierung</collection>
    <collection role="institutes" number="">8 Zerstörungsfreie Prüfung</collection>
    <collection role="institutes" number="">8.5 Röntgenbildgebung</collection>
    <collection role="institutes" number="">9 Komponentensicherheit</collection>
    <collection role="institutes" number="">9.3 Schweißtechnische Fertigungsverfahren</collection>
    <collection role="institutes" number="">9.4 Integrität von Schweißverbindungen</collection>
    <collection role="themenfelder" number="">Material</collection>
    <collection role="literaturgattung" number="">Verlagsliteratur</collection>
    <collection role="fulltextaccess" number="">Datei für die Öffentlichkeit verfügbar ("Open Access")</collection>
    <collection role="unnumberedseries" number="">Wissenschaftliche Artikel der BAM</collection>
    <thesisPublisher>Bundesanstalt für Materialforschung und -prüfung (BAM)</thesisPublisher>
    <file>https://opus4.kobv.de/opus4-bam/files/51171/2020_Charmi_Mechanical anisotropy of additively manufactured stainless steel 316L.pdf</file>
  </doc>
  <doc>
    <id>53604</id>
    <completedYear/>
    <publishedYear>2021</publishedYear>
    <thesisYearAccepted/>
    <language>eng</language>
    <pageFirst>5342</pageFirst>
    <pageLast>5356</pageLast>
    <pageNumber/>
    <edition/>
    <issue>12</issue>
    <volume>52</volume>
    <type>article</type>
    <publisherName>Springer</publisherName>
    <publisherPlace>Boston</publisherPlace>
    <creatingCorporation/>
    <contributingCorporation/>
    <belongsToBibliography>1</belongsToBibliography>
    <completedDate>--</completedDate>
    <publishedDate>--</publishedDate>
    <thesisDateAccepted>--</thesisDateAccepted>
    <title language="eng">Towards the optimization of post-laser powder bed fusion stress-relieve treatments of stainless steel 316L</title>
    <abstract language="eng">This study reports on the stress relaxation potential of stress-relieving heat treatments for laser powder bed fused 316L. The residual stress is monitored non-destructively using neutron diffraction before and after the heat treatment. Moreover, the evolution of the microstructure is analysed using scanning electron microscopy. The results show, that a strong relaxation of the residual stress is obtained when applying a heat treatment temperature at 900°C. However, the loss of the cellular substructure needs to be considered when applying this heat treatment strategy.</abstract>
    <parentTitle language="eng">Metallurgical and materials transactions A</parentTitle>
    <identifier type="doi">10.1007/s11661-021-06472-6</identifier>
    <identifier type="urn">urn:nbn:de:kobv:b43-536045</identifier>
    <identifier type="issn">1543-1940</identifier>
    <enrichment key="opus.source">publish</enrichment>
    <enrichment key="date_peer_review">04.11.2021</enrichment>
    <licence>Creative Commons - CC BY - Namensnennung 4.0 International</licence>
    <author>Maximilian Sprengel</author>
    <author>Alexander Ulbricht</author>
    <author>Alexander Evans</author>
    <author>Arne Kromm</author>
    <author>Konstantin Sommer</author>
    <author>Tiago Werner</author>
    <author>J. Kelleher</author>
    <author>Giovanni Bruno</author>
    <author>Thomas Kannengießer</author>
    <subject>
      <language>eng</language>
      <type>uncontrolled</type>
      <value>Residual stress</value>
    </subject>
    <subject>
      <language>eng</language>
      <type>uncontrolled</type>
      <value>Additive manufacturing</value>
    </subject>
    <subject>
      <language>eng</language>
      <type>uncontrolled</type>
      <value>Neutron diffraction</value>
    </subject>
    <subject>
      <language>deu</language>
      <type>uncontrolled</type>
      <value>Projekt AGIL - Alterung additiv gefertigter metallischer Materialien und Komponenten</value>
    </subject>
    <collection role="ddc" number="620">Ingenieurwissenschaften und zugeordnete Tätigkeiten</collection>
    <collection role="institutes" number="">5 Werkstofftechnik</collection>
    <collection role="institutes" number="">5.1 Mikrostruktur Design und Degradation</collection>
    <collection role="institutes" number="">8 Zerstörungsfreie Prüfung</collection>
    <collection role="institutes" number="">8.5 Röntgenbildgebung</collection>
    <collection role="institutes" number="">9 Komponentensicherheit</collection>
    <collection role="institutes" number="">9.4 Integrität von Schweißverbindungen</collection>
    <collection role="themenfelder" number="">Material</collection>
    <collection role="themenfelder" number="">Degradationsmechanismen</collection>
    <collection role="literaturgattung" number="">Verlagsliteratur</collection>
    <collection role="fulltextaccess" number="">Datei für die Öffentlichkeit verfügbar ("Open Access")</collection>
    <collection role="unnumberedseries" number="">Wissenschaftliche Artikel der BAM</collection>
    <thesisPublisher>Bundesanstalt für Materialforschung und -prüfung (BAM)</thesisPublisher>
    <file>https://opus4.kobv.de/opus4-bam/files/53604/Sprengel2021_Article_TowardsTheOptimizationOfPost-L.pdf</file>
  </doc>
  <doc>
    <id>52819</id>
    <completedYear/>
    <publishedYear>2021</publishedYear>
    <thesisYearAccepted/>
    <language>eng</language>
    <pageFirst/>
    <pageLast/>
    <pageNumber/>
    <edition/>
    <issue/>
    <volume/>
    <type>lecture</type>
    <publisherName/>
    <publisherPlace/>
    <creatingCorporation/>
    <contributingCorporation/>
    <belongsToBibliography>0</belongsToBibliography>
    <completedDate>--</completedDate>
    <publishedDate>--</publishedDate>
    <thesisDateAccepted>--</thesisDateAccepted>
    <title language="eng">Tales from Within: Residual Stress and Void Formation in LPBF 316L</title>
    <abstract language="eng">An unusual microstructure, inherent residual stresses and void formation are the three key aspects to control when assessing metallic parts made by LPBF. This talk explains an experiment to unravel the interlinked influence of the two mechanisms for the formation of residual stresses in LPBF: the temperature gradient mechanism and constricted solidification shrinkage. The impact of each mechanism on the shape and magnitudes of the residual stress distribution is described. Combined results from neutron diffraction, X-ray diffraction, computed tomography and in-situ thermography are presented.&#13;
Also, influence of scan strategies as well as surface roughness of subjacent layers on void formation is shown. Results from computed tomography and in-situ thermography of a specimen dedicated to study the interaction of the melt pool with layers of powder underneath the currently illuminated surface are presented.</abstract>
    <enrichment key="eventName">2nd Workshop on In-situ Monitoring and Microstructure Development in Additive Manufacturing</enrichment>
    <enrichment key="eventPlace">Online meeting</enrichment>
    <enrichment key="eventStart">19.04.2021</enrichment>
    <enrichment key="eventEnd">20.04.2021</enrichment>
    <enrichment key="opus.source">publish</enrichment>
    <enrichment key="opus.doi.autoCreate">false</enrichment>
    <enrichment key="opus.urn.autoCreate">true</enrichment>
    <enrichment key="InvitedTalks">0</enrichment>
    <author>Alexander Ulbricht</author>
    <subject>
      <language>eng</language>
      <type>uncontrolled</type>
      <value>Neutron diffraction</value>
    </subject>
    <subject>
      <language>eng</language>
      <type>uncontrolled</type>
      <value>Laser powder bed fusion</value>
    </subject>
    <subject>
      <language>eng</language>
      <type>uncontrolled</type>
      <value>In-situ thermography</value>
    </subject>
    <subject>
      <language>eng</language>
      <type>uncontrolled</type>
      <value>Computed tomography</value>
    </subject>
    <subject>
      <language>eng</language>
      <type>uncontrolled</type>
      <value>X-ray diffraction</value>
    </subject>
    <subject>
      <language>eng</language>
      <type>uncontrolled</type>
      <value>Residual stress</value>
    </subject>
    <subject>
      <language>eng</language>
      <type>uncontrolled</type>
      <value>Pore formation</value>
    </subject>
    <subject>
      <language>eng</language>
      <type>uncontrolled</type>
      <value>AISI 316L</value>
    </subject>
    <collection role="ddc" number="620">Ingenieurwissenschaften und zugeordnete Tätigkeiten</collection>
    <collection role="institutes" number="">8 Zerstörungsfreie Prüfung</collection>
    <collection role="institutes" number="">8.5 Röntgenbildgebung</collection>
    <collection role="institutes" number="">9 Komponentensicherheit</collection>
    <collection role="institutes" number="">9.4 Integrität von Schweißverbindungen</collection>
    <collection role="themenfelder" number="">Material</collection>
    <collection role="fulltextaccess" number="">Datei im Netzwerk der BAM verfügbar ("Closed Access")</collection>
    <collection role="literaturgattung" number="">Präsentation</collection>
    <collection role="institutes" number="">8.0 Abteilungsleitung und andere</collection>
    <collection role="institutes" number="">9.6 Additive Fertigung metallischer Komponenten</collection>
    <collection role="themenfelder" number="">Additive Fertigung</collection>
  </doc>
  <doc>
    <id>49805</id>
    <completedYear/>
    <publishedYear>2019</publishedYear>
    <thesisYearAccepted/>
    <language>eng</language>
    <pageFirst/>
    <pageLast/>
    <pageNumber/>
    <edition/>
    <issue/>
    <volume/>
    <type>lecture</type>
    <publisherName/>
    <publisherPlace/>
    <creatingCorporation/>
    <contributingCorporation/>
    <belongsToBibliography>0</belongsToBibliography>
    <completedDate>--</completedDate>
    <publishedDate>--</publishedDate>
    <thesisDateAccepted>--</thesisDateAccepted>
    <title language="eng">How Temperature Gradient Influences the Formation of Residual Stresses in Metallic Parts Made by L-PBF</title>
    <abstract language="eng">Rapid cooling rates and steep temperature gradients are characteristic of additively manufactured (AM) parts and important factors for residual stress formation which have implications on structural integrity. This study examined the influence of heat input  on the distribution of residual stresses in two prisms produced by laser powder bed fusion (L-PBF) of austenitic stainless steel 316L.&#13;
The layers of the prisms were  exposed using two distinct helix scanning  strategies: one scanned from the centre to the perimeter and the other from the perimeter to the centre. Residual stresses were characterised at one plane perpendicular to the building direction at half of its build height using neutron diffraction. In addition, the defect distribution was analysed via micro X-ray computed tomography (µCT) in a twin specimen.&#13;
Both scanning strategies reveal residual stress distributions typical for AM: compressive stresses in the bulk and tensile stresses at the surface. However, temperature gradients and maximum stress levels differ due to the different heat input. Regarding the X-ray µCT results, they show an accumulation of defects at the corners where the laser direction turned through 90°. &#13;
The results demonstrate that neutron diffraction and X-ray µCT can be successfully used as non-destructive methods to analyse through-thickness residual stress and defect distribution in AM parts, and in the presented case, illustrate the influence of scanning strategies. This approach contributes to deeper assessment of structural integrity of AM materials and components.</abstract>
    <enrichment key="eventName">First European Conference on Structural Integrity of Additively Manufactured Materials (ESIAM19)</enrichment>
    <enrichment key="eventPlace">Trondheim, Norwegen</enrichment>
    <enrichment key="eventStart">09.09.2019</enrichment>
    <enrichment key="eventEnd">11.09.2019</enrichment>
    <enrichment key="opus.doi.autoCreate">false</enrichment>
    <enrichment key="opus.urn.autoCreate">true</enrichment>
    <enrichment key="InvitedTalks">0</enrichment>
    <author>Alexander Ulbricht</author>
    <subject>
      <language>eng</language>
      <type>uncontrolled</type>
      <value>AGIL</value>
    </subject>
    <subject>
      <language>eng</language>
      <type>uncontrolled</type>
      <value>Neutron diffraction</value>
    </subject>
    <subject>
      <language>eng</language>
      <type>uncontrolled</type>
      <value>Thermography</value>
    </subject>
    <subject>
      <language>eng</language>
      <type>uncontrolled</type>
      <value>Additive manufacturing</value>
    </subject>
    <subject>
      <language>eng</language>
      <type>uncontrolled</type>
      <value>Residual stress</value>
    </subject>
    <collection role="ddc" number="620">Ingenieurwissenschaften und zugeordnete Tätigkeiten</collection>
    <collection role="fulltextaccess" number="">Datei im Netzwerk der BAM verfügbar ("Closed Access")</collection>
    <collection role="literaturgattung" number="">Präsentation</collection>
  </doc>
  <doc>
    <id>51793</id>
    <completedYear/>
    <publishedYear>2020</publishedYear>
    <thesisYearAccepted/>
    <language>eng</language>
    <pageFirst/>
    <pageLast/>
    <pageNumber/>
    <edition/>
    <issue/>
    <volume/>
    <type>poster</type>
    <publisherName/>
    <publisherPlace/>
    <creatingCorporation/>
    <contributingCorporation/>
    <belongsToBibliography>0</belongsToBibliography>
    <completedDate>--</completedDate>
    <publishedDate>--</publishedDate>
    <thesisDateAccepted>--</thesisDateAccepted>
    <title language="eng">Separation of the Formation Mechanisms of Residual Stresses in LPBF 316L</title>
    <abstract language="eng">Rapid cooling rates and steep temperature gradients are characteristic of additively manufactured parts and important factors for the residual stress formation. This study examined the influence of heat accumulation on the distribution of residual stress in two prisms produced by Laser Powder Bed Fusion (LPBF) of austenitic stainless steel 316L. The layers of the prisms were exposed using two different border fill scan strategies: one scanned from the centre to the perimeter and the other from the perimeter to the centre. The goal was to reveal the effect of different heat inputs on samples featuring the same solidification shrinkage. Residual stress was characterised in one plane perpendicular to the building direction at the mid height using Neutron and Lab X-ray diffraction. Thermography data obtained during the build process were analysed in order to correlate the cooling rates and apparent surface temperatures with the residual stress results. Optical microscopy and micro computed tomography were used to correlate defect populations with the residual stress distribution. The two scanning strategies led to residual stress distributions that were typical for additively manufactured components: compressive stresses in the bulk and tensile stresses at the surface. However, due to the different heat accumulation, the maximum residual stress levels differed. We concluded that solidification shrinkage plays a major role in determining the shape of the residual stress distribution, while the temperature gradient mechanism appears to determine the magnitude of peak residual stresses.</abstract>
    <enrichment key="eventName">MLZ User Meeting 2020</enrichment>
    <enrichment key="eventPlace">Online meeting</enrichment>
    <enrichment key="eventStart">08.12.2020</enrichment>
    <enrichment key="eventEnd">10.12.2020</enrichment>
    <enrichment key="opus.doi.autoCreate">false</enrichment>
    <enrichment key="opus.urn.autoCreate">true</enrichment>
    <author>Alexander Ulbricht</author>
    <subject>
      <language>eng</language>
      <type>uncontrolled</type>
      <value>Computed tomography</value>
    </subject>
    <subject>
      <language>eng</language>
      <type>uncontrolled</type>
      <value>Neutron diffraction</value>
    </subject>
    <subject>
      <language>eng</language>
      <type>uncontrolled</type>
      <value>X-ray diffraction</value>
    </subject>
    <subject>
      <language>eng</language>
      <type>uncontrolled</type>
      <value>Additive manufacturing</value>
    </subject>
    <subject>
      <language>eng</language>
      <type>uncontrolled</type>
      <value>Residual stress</value>
    </subject>
    <subject>
      <language>eng</language>
      <type>uncontrolled</type>
      <value>Thermography</value>
    </subject>
    <subject>
      <language>eng</language>
      <type>uncontrolled</type>
      <value>LPBF</value>
    </subject>
    <subject>
      <language>eng</language>
      <type>uncontrolled</type>
      <value>Laser Powder Bed Fusion</value>
    </subject>
    <collection role="ddc" number="620">Ingenieurwissenschaften und zugeordnete Tätigkeiten</collection>
    <collection role="institutes" number="">8 Zerstörungsfreie Prüfung</collection>
    <collection role="institutes" number="">8.5 Röntgenbildgebung</collection>
    <collection role="institutes" number="">9 Komponentensicherheit</collection>
    <collection role="institutes" number="">9.3 Schweißtechnische Fertigungsverfahren</collection>
    <collection role="institutes" number="">9.4 Integrität von Schweißverbindungen</collection>
    <collection role="themenfelder" number="">Material</collection>
    <collection role="themenfelder" number="">Degradationsmechanismen</collection>
    <collection role="fulltextaccess" number="">Datei im Netzwerk der BAM verfügbar ("Closed Access")</collection>
    <collection role="literaturgattung" number="">Präsentation</collection>
    <collection role="institutes" number="">8.0 Abteilungsleitung und andere</collection>
    <collection role="themenfelder" number="">Additive Fertigung</collection>
  </doc>
  <doc>
    <id>50824</id>
    <completedYear/>
    <publishedYear>2020</publishedYear>
    <thesisYearAccepted/>
    <language>eng</language>
    <pageFirst>701</pageFirst>
    <pageLast/>
    <pageNumber/>
    <edition/>
    <issue>6</issue>
    <volume>10</volume>
    <type>article</type>
    <publisherName>MDPI</publisherName>
    <publisherPlace/>
    <creatingCorporation/>
    <contributingCorporation/>
    <belongsToBibliography>1</belongsToBibliography>
    <completedDate>--</completedDate>
    <publishedDate>--</publishedDate>
    <thesisDateAccepted>--</thesisDateAccepted>
    <title language="eng">Residual Stress and Microstructure of a Ti-6Al-4V Wire Arc Additive Manufacturing Hybrid Demonstrator</title>
    <abstract language="eng">Wire Arc Additive Manufacturing (WAAM) features high deposition rates and, thus, allows production of large components that are relevant for aerospace applications. However, a lot of aerospace parts are currently produced by forging or machining alone to ensure fast production and to obtain good mechanical properties; the use of these conventional process routes causes high tooling and material costs. A hybrid approach (a combination of forging and WAAM) allows making production more efficient. In this fashion, further structural or functional features can be built in any direction without using additional tools for every part. By using a combination of forging basic geometries with one tool set and adding the functional features by means of WAAM, the tool costs and material waste can be reduced compared to either completely forged or machined parts. One of the factors influencing the structural integrity of additively manufactured parts are (high) residual stresses, generated during the build process. In this study, the triaxial residual stress profiles in a hybrid WAAM part are reported, as determined by neutron diffraction. The analysis is complemented by microstructural investigations, showing a gradient of microstructure (shape and size of grains) along the part height. The highest residual stresses were found in the transition Zone (between WAAM and forged part). The total stress range showed to be lower than expected for WAAM components. This could be explained by the thermal history of the component.</abstract>
    <parentTitle language="eng">Metals</parentTitle>
    <identifier type="doi">10.3390/met10060701</identifier>
    <identifier type="urn">urn:nbn:de:kobv:b43-508245</identifier>
    <enrichment key="date_peer_review">17.08.2020</enrichment>
    <licence>Creative Commons - CC BY - Namensnennung 4.0 International</licence>
    <author>Tatiana Mishurova</author>
    <author>B. Sydow</author>
    <author>Tobias Thiede</author>
    <author>I. Sizova</author>
    <author>Alexander Ulbricht</author>
    <author>M. Bambach</author>
    <author>Giovanni Bruno</author>
    <subject>
      <language>eng</language>
      <type>uncontrolled</type>
      <value>Additive manufacturing</value>
    </subject>
    <subject>
      <language>eng</language>
      <type>uncontrolled</type>
      <value>Neutron diffraction</value>
    </subject>
    <subject>
      <language>eng</language>
      <type>uncontrolled</type>
      <value>Residual stress</value>
    </subject>
    <subject>
      <language>eng</language>
      <type>uncontrolled</type>
      <value>Hybrid manufacturing</value>
    </subject>
    <subject>
      <language>eng</language>
      <type>uncontrolled</type>
      <value>WAAM</value>
    </subject>
    <subject>
      <language>eng</language>
      <type>uncontrolled</type>
      <value>Ti-6Al-4V</value>
    </subject>
    <collection role="ddc" number="620">Ingenieurwissenschaften und zugeordnete Tätigkeiten</collection>
    <collection role="institutes" number="">8 Zerstörungsfreie Prüfung</collection>
    <collection role="institutes" number="">8.5 Röntgenbildgebung</collection>
    <collection role="themenfelder" number="">Material</collection>
    <collection role="themenfelder" number="">Degradationsmechanismen</collection>
    <collection role="literaturgattung" number="">Verlagsliteratur</collection>
    <collection role="fulltextaccess" number="">Datei für die Öffentlichkeit verfügbar ("Open Access")</collection>
    <collection role="unnumberedseries" number="">Wissenschaftliche Artikel der BAM</collection>
    <collection role="themenfelder" number="">Additive Fertigung</collection>
    <thesisPublisher>Bundesanstalt für Materialforschung und -prüfung (BAM)</thesisPublisher>
    <file>https://opus4.kobv.de/opus4-bam/files/50824/Mishurova_et_al2020_BTU_metals.pdf</file>
  </doc>
</export-example>
