<?xml version="1.0" encoding="utf-8"?>
<export-example>
  <doc>
    <id>45299</id>
    <completedYear/>
    <publishedYear>2018</publishedYear>
    <thesisYearAccepted/>
    <language>deu</language>
    <pageFirst/>
    <pageLast/>
    <pageNumber/>
    <edition/>
    <issue/>
    <volume/>
    <type>lecture</type>
    <publisherName/>
    <publisherPlace/>
    <creatingCorporation/>
    <contributingCorporation/>
    <belongsToBibliography>0</belongsToBibliography>
    <completedDate>--</completedDate>
    <publishedDate>--</publishedDate>
    <thesisDateAccepted>--</thesisDateAccepted>
    <title language="deu">Dichtungsverhalten bei niedrigen Temperaturen - Untersuchung der unteren Temperatureinsatzgrenze</title>
    <abstract language="deu">Elastomere werden vielfach in Produkten eingesetzt, die bei verschiedenen Temperaturen verwendet werden. Dabei sind O-Ringe kostengünstige Dichtelemente, die allerdings für die Funktionsfähigkeit und Sicherheit eines Produkts entscheidend sind. Die untere Temperatureinsatzgrenze ist dabei durchaus relevant und aus wissenschaftlicher Sicht nicht allgemeingültig zu definieren, da diese einerseits durch die Änderungen der Materialeigenschaften im Zuge des Gummi-Glas-Übergangs definiert werden, die Temperaturlage dieses Übergangs jedoch sehr stark von den jeweiligen Einsatzbedingungen (z.B. Frequenz) abhängt. Dadurch ergeben sich große Unterschiede zwischen statischen und dynamischen Anwendungen. Verschiedene Untersuchungen sollen vorgestellt und interpretiert werden, um das Auditorium auf verschiedene Herausforderungen aufmerksam zu machen und Lösungsansätze vorzustellen...</abstract>
    <enrichment key="eventName">ISGATEC O-Ring Forum</enrichment>
    <enrichment key="eventPlace">Mannheim, Germany</enrichment>
    <enrichment key="eventStart">20.06.2018</enrichment>
    <enrichment key="eventEnd">21.06.2018</enrichment>
    <enrichment key="InvitedTalks">0</enrichment>
    <author>Matthias Jaunich</author>
    <subject>
      <language>deu</language>
      <type>uncontrolled</type>
      <value>Dichtung</value>
    </subject>
    <subject>
      <language>deu</language>
      <type>uncontrolled</type>
      <value>Glasübergang</value>
    </subject>
    <subject>
      <language>deu</language>
      <type>uncontrolled</type>
      <value>O-Ring</value>
    </subject>
    <subject>
      <language>deu</language>
      <type>uncontrolled</type>
      <value>Druckverformungsrest</value>
    </subject>
    <subject>
      <language>deu</language>
      <type>uncontrolled</type>
      <value>Leckagerate</value>
    </subject>
    <collection role="ddc" number="620">Ingenieurwissenschaften und zugeordnete Tätigkeiten</collection>
    <collection role="ddc" number="621">Angewandte Physik</collection>
    <collection role="fulltextaccess" number="">Datei im Netzwerk der BAM verfügbar ("Closed Access")</collection>
    <collection role="literaturgattung" number="">Präsentation</collection>
  </doc>
  <doc>
    <id>37554</id>
    <completedYear/>
    <publishedYear>2016</publishedYear>
    <thesisYearAccepted/>
    <language>eng</language>
    <pageFirst/>
    <pageLast/>
    <pageNumber/>
    <edition/>
    <issue/>
    <volume/>
    <type>lecture</type>
    <publisherName/>
    <publisherPlace/>
    <creatingCorporation/>
    <contributingCorporation/>
    <belongsToBibliography>0</belongsToBibliography>
    <completedDate>--</completedDate>
    <publishedDate>--</publishedDate>
    <thesisDateAccepted>--</thesisDateAccepted>
    <title language="eng">Long-term behavior of elastomer seals and polymers for neutron shielding</title>
    <abstract language="eng">The long time-frame of the necessary safe enclosure of radioactive waste in containers gains interna-tionally an increasing attention. As well extended storage periods as a usually necessary subsequent transportation after storage have to be evaluated.&#13;
In Germany, the concept of dry interim storage in dual purpose metal casks before disposal is being pursued for spent nuclear fuel (SNF) and high level waste (HLW) management. The initially planned and established dry interim storage license duration of up to 40 years will be too short and its exten-sion will become necessary since there is no repository available in due time. &#13;
The main safety relevant components are the thick-walled dual purpose metal casks. These casks consist e.g. of a monolithic cask body with integrated neutron shielding components (polymers, e.g. polyethylene) and a monitored double lid barrier system equipped with metal and elastomer seals. The metal seals of this bolted closure system guarantee the required leak-tightness whereas the elastomer seals allow for leakage rate measurement of the metal seals. &#13;
At BAM we focus on the long-term performance of the sealing system and neutron shielding materials as their application conditions have to be concerned as rather demanding.&#13;
Therefore, BAM began to investigate the overall function and long-term behavior of elastomer and metal seals and also the irradiation influence on neutron shielding materials. &#13;
Recently a new project was initiated to expand our investigations to get more and in some context better applicable data.&#13;
This paper describes the approach of our new research project with the aim of further closure of existing knowledge gaps and presents an overview of investigations concerning the low temperature behavior of elastomer seals, of running long-term tests on elastomer seals at different temperatures under static conditions and the influence of gamma irradiation on neutron shielding materials.</abstract>
    <enrichment key="eventName">18th International Symposium on the Packaging and Transportation of Radioactive Materials (PATRAM) 2016</enrichment>
    <enrichment key="eventPlace">Kobe, Japan</enrichment>
    <enrichment key="eventStart">18.09.2016</enrichment>
    <enrichment key="eventEnd">23.09.2016</enrichment>
    <enrichment key="InvitedTalks">0</enrichment>
    <author>Matthias Jaunich</author>
    <subject>
      <language>eng</language>
      <type>uncontrolled</type>
      <value>Aging</value>
    </subject>
    <subject>
      <language>eng</language>
      <type>uncontrolled</type>
      <value>Irradiation</value>
    </subject>
    <subject>
      <language>eng</language>
      <type>uncontrolled</type>
      <value>Neutron shielding</value>
    </subject>
    <subject>
      <language>eng</language>
      <type>uncontrolled</type>
      <value>Elastomer seal</value>
    </subject>
    <collection role="ddc" number="621">Angewandte Physik</collection>
    <collection role="fulltextaccess" number="">Datei im Netzwerk der BAM verfügbar ("Closed Access")</collection>
    <collection role="literaturgattung" number="">Präsentation</collection>
  </doc>
  <doc>
    <id>37362</id>
    <completedYear/>
    <publishedYear>2016</publishedYear>
    <thesisYearAccepted/>
    <language>eng</language>
    <pageFirst>III</pageFirst>
    <pageLast/>
    <pageNumber/>
    <edition/>
    <issue>1</issue>
    <volume>2016/51</volume>
    <type>article</type>
    <publisherName>Elsevier Sci. Ltd.</publisherName>
    <publisherPlace>Oxford, UK</publisherPlace>
    <creatingCorporation/>
    <contributingCorporation/>
    <belongsToBibliography>0</belongsToBibliography>
    <completedDate>--</completedDate>
    <publishedDate>--</publishedDate>
    <thesisDateAccepted>--</thesisDateAccepted>
    <title language="eng">Polymer Testing - Editorial</title>
    <abstract language="eng">Thoughts about getting started as Associate Editor for Polymer Testing.</abstract>
    <parentTitle language="eng">Polymer Testing</parentTitle>
    <identifier type="doi">10.1016/S0142-9418(16)30279-3</identifier>
    <identifier type="issn">0142-9418</identifier>
    <author>Matthias Jaunich</author>
    <subject>
      <language>eng</language>
      <type>uncontrolled</type>
      <value>Editorial</value>
    </subject>
    <subject>
      <language>eng</language>
      <type>uncontrolled</type>
      <value>Getting started</value>
    </subject>
    <subject>
      <language>eng</language>
      <type>uncontrolled</type>
      <value>Polymer Testing</value>
    </subject>
    <collection role="ddc" number="620">Ingenieurwissenschaften und zugeordnete Tätigkeiten</collection>
    <collection role="ddc" number="621">Angewandte Physik</collection>
    <collection role="literaturgattung" number="">Verlagsliteratur</collection>
    <collection role="fulltextaccess" number="">Datei im Netzwerk der BAM verfügbar ("Closed Access")</collection>
  </doc>
  <doc>
    <id>48225</id>
    <completedYear/>
    <publishedYear>2019</publishedYear>
    <thesisYearAccepted/>
    <language>eng</language>
    <pageFirst>57</pageFirst>
    <pageLast>62</pageLast>
    <pageNumber/>
    <edition/>
    <issue/>
    <volume/>
    <type>conferenceobject</type>
    <publisherName/>
    <publisherPlace/>
    <creatingCorporation>GRS</creatingCorporation>
    <contributingCorporation/>
    <belongsToBibliography>0</belongsToBibliography>
    <completedDate>--</completedDate>
    <publishedDate>--</publishedDate>
    <thesisDateAccepted>--</thesisDateAccepted>
    <title language="eng">Long-term evaluation of sealing systems for radioactive waste packages</title>
    <abstract language="eng">The investigation of the long-term performance of sealing systems employed in containers for radioactive waste and spent nuclear fuel is one research focus area for division 3.4 “Safety of Storage Containers” at the Bundesanstalt für Materialforschung und -prüfung (BAM). Our investigations comprise investigations on metallic and elastomeric seals and covers experimental investigations to get a database on the component/material behaviour, work on analytical descriptions and numerical analysis. Our aim is to understand the long-term behaviour of the sealing systems for evaluation of their performance during possible extended interim storage and subsequent transportation.</abstract>
    <parentTitle language="eng">Proceedings of the 3rd Workshop on Safety of Extended Dry Storage of Spent Nuclear Fuel</parentTitle>
    <enrichment key="eventName">3rd Workshop on Safety of Extended Dry Storage of Spent Nuclear Fuel</enrichment>
    <enrichment key="eventPlace">Garching, Germany</enrichment>
    <enrichment key="eventStart">05.06.2019</enrichment>
    <enrichment key="eventEnd">07.06.2019</enrichment>
    <enrichment key="opus.doi.autoCreate">false</enrichment>
    <enrichment key="opus.urn.autoCreate">true</enrichment>
    <author>Matthias Jaunich</author>
    <author>Tobias Grelle</author>
    <author>Anja Kömmling</author>
    <author>Dietmar Wolff</author>
    <author>Holger Völzke</author>
    <subject>
      <language>eng</language>
      <type>uncontrolled</type>
      <value>Seal performance</value>
    </subject>
    <subject>
      <language>eng</language>
      <type>uncontrolled</type>
      <value>Rubber seal</value>
    </subject>
    <subject>
      <language>eng</language>
      <type>uncontrolled</type>
      <value>Metallic seal</value>
    </subject>
    <subject>
      <language>eng</language>
      <type>uncontrolled</type>
      <value>Ageing</value>
    </subject>
    <collection role="ddc" number="620">Ingenieurwissenschaften und zugeordnete Tätigkeiten</collection>
    <collection role="ddc" number="621">Angewandte Physik</collection>
    <collection role="fulltextaccess" number="">Datei im Netzwerk der BAM verfügbar ("Closed Access")</collection>
    <collection role="literaturgattung" number="">Graue Literatur</collection>
  </doc>
  <doc>
    <id>40381</id>
    <completedYear/>
    <publishedYear>2017</publishedYear>
    <thesisYearAccepted/>
    <language>eng</language>
    <pageFirst/>
    <pageLast/>
    <pageNumber/>
    <edition/>
    <issue/>
    <volume/>
    <type>lecture</type>
    <publisherName/>
    <publisherPlace/>
    <creatingCorporation/>
    <contributingCorporation/>
    <belongsToBibliography>0</belongsToBibliography>
    <completedDate>--</completedDate>
    <publishedDate>--</publishedDate>
    <thesisDateAccepted>--</thesisDateAccepted>
    <title language="eng">Characterisation of degradation and determination of end-of-lifetime criterion for O-ring seals</title>
    <abstract language="eng">The ageing of polymers, including elastomers, is an undesirable but inevitable process leading to a limited lifetime of rubber products such as seals. Independent of the application, as e.g. automotive, piping or container applications, a long lifetime or at least a timely exchange of a seal before occurence of critical failure is desired. &#13;
In order to investigate the degradation of material properties and to determine the lifetime of elastomers used as seals, an ageing programme was started with hydrogenated acrylonitrile butadiene rubber (HNBR), ethylene propylene diene rubber (EPDM) and fluorocarbon rubber (FKM) [1-3]. Both O-ring seals (uncompressed and compressed by 25 %) with a cord diameter of 10 mm as well as sheets with a thickness of 2 mm were aged at 75 °C, 100 °C, 125 °C and 150 °C for up to two years. The changes of material properties during ageing were characterised for each material using the sheets by means of e.g. dynamic-mechanical analysis and tensile tests, while sealing properties such as compression stress relaxation (CSR), compression set (CS) and leakage rate were determined on O-rings. The experimental results indicate that while material properties, CSR and CS show considerable degradation effects, the static leakage rate stays constant or even decreases before failure occurs quite suddenly at advanced degradation levels. This reveals that static leakage rate has only limited sensitivity for the degradation of the seal material. &#13;
Our approach to determine a suitable end of lifetime criterion, which involves a partial decompression of the seal during the leakage test, is presented and discussed.</abstract>
    <enrichment key="eventName">RubberCon 2017</enrichment>
    <enrichment key="eventPlace">Prague, Czech Republic</enrichment>
    <enrichment key="eventStart">23.05.2017</enrichment>
    <enrichment key="eventEnd">25.05.2017</enrichment>
    <enrichment key="InvitedTalks">0</enrichment>
    <author>Matthias Jaunich</author>
    <subject>
      <language>eng</language>
      <type>uncontrolled</type>
      <value>Rubber seal</value>
    </subject>
    <subject>
      <language>eng</language>
      <type>uncontrolled</type>
      <value>Ageing</value>
    </subject>
    <subject>
      <language>eng</language>
      <type>uncontrolled</type>
      <value>Leakage</value>
    </subject>
    <collection role="ddc" number="620">Ingenieurwissenschaften und zugeordnete Tätigkeiten</collection>
    <collection role="ddc" number="621">Angewandte Physik</collection>
    <collection role="fulltextaccess" number="">Datei im Netzwerk der BAM verfügbar ("Closed Access")</collection>
    <collection role="literaturgattung" number="">Präsentation</collection>
  </doc>
  <doc>
    <id>48206</id>
    <completedYear/>
    <publishedYear>2018</publishedYear>
    <thesisYearAccepted/>
    <language>eng</language>
    <pageFirst>32</pageFirst>
    <pageLast>34</pageLast>
    <pageNumber/>
    <edition/>
    <issue/>
    <volume/>
    <type>article</type>
    <publisherName>Nuclear Institute</publisherName>
    <publisherPlace>London</publisherPlace>
    <creatingCorporation/>
    <contributingCorporation/>
    <belongsToBibliography>0</belongsToBibliography>
    <completedDate>--</completedDate>
    <publishedDate>--</publishedDate>
    <thesisDateAccepted>--</thesisDateAccepted>
    <title language="eng">Component and material investigations on metal seals for high level radioactive waste containers</title>
    <abstract language="eng">Long-term investigations performed at BAM look to extend the state of knowledge on safety-related components of interim storage containers. Metal seals act as the primary sealing barrier in the bolted double lid closure system of the containers. The behaviour of metal seals has been investigated for ageing times up to 8.5 years and for various temperatures. The main cause for reduction in useable resilience overtime was due to creep deformation of the outer jacket of the seal.</abstract>
    <parentTitle language="eng">Nuclear future</parentTitle>
    <identifier type="issn">1745-2058</identifier>
    <author>Tobias Grelle</author>
    <author>Dietmar Wolff</author>
    <author>Ulrich Probst</author>
    <author>Matthias Jaunich</author>
    <author>Holger Völzke</author>
    <subject>
      <language>eng</language>
      <type>uncontrolled</type>
      <value>Metal seal</value>
    </subject>
    <subject>
      <language>eng</language>
      <type>uncontrolled</type>
      <value>Radioactive waste containers</value>
    </subject>
    <subject>
      <language>eng</language>
      <type>uncontrolled</type>
      <value>Creep</value>
    </subject>
    <subject>
      <language>eng</language>
      <type>uncontrolled</type>
      <value>Long-term behaviour</value>
    </subject>
    <collection role="ddc" number="621">Angewandte Physik</collection>
    <collection role="fulltextaccess" number="">Datei im Netzwerk der BAM verfügbar ("Closed Access")</collection>
    <collection role="literaturgattung" number="">Graue Literatur</collection>
  </doc>
  <doc>
    <id>33454</id>
    <completedYear/>
    <publishedYear>2015</publishedYear>
    <thesisYearAccepted/>
    <language>deu</language>
    <pageFirst/>
    <pageLast/>
    <pageNumber/>
    <edition/>
    <issue/>
    <volume/>
    <type>lecture</type>
    <publisherName/>
    <publisherPlace/>
    <creatingCorporation/>
    <contributingCorporation/>
    <belongsToBibliography>0</belongsToBibliography>
    <completedDate>--</completedDate>
    <publishedDate>--</publishedDate>
    <thesisDateAccepted>--</thesisDateAccepted>
    <title language="deu">Investigation of Elastomer Seal Behaviour for Transport and Storage Packages</title>
    <parentTitle language="deu">Ramtrans 2015, 10th International Conference on Radioactive Materials Transport and Storage</parentTitle>
    <identifier type="old">36548</identifier>
    <enrichment key="eventName">Ramtrans 2015, 10th International Conference on Radioactive Materials Transport and Storage</enrichment>
    <enrichment key="eventPlace">Oxford, United Kingdom</enrichment>
    <enrichment key="eventStart">2015-05-19</enrichment>
    <enrichment key="eventEnd">2015-05-21</enrichment>
    <enrichment key="InvitedTalks">0</enrichment>
    <author>Matthias Jaunich</author>
    <collection role="fulltextaccess" number="">Weder Datei noch physisches Exemplar vorhanden ("No Access")</collection>
    <collection role="literaturgattung" number="">Präsentation</collection>
  </doc>
  <doc>
    <id>30667</id>
    <completedYear/>
    <publishedYear>2014</publishedYear>
    <thesisYearAccepted/>
    <language>deu</language>
    <pageFirst/>
    <pageLast/>
    <pageNumber/>
    <edition/>
    <issue/>
    <volume/>
    <type>lecture</type>
    <publisherName/>
    <publisherPlace/>
    <creatingCorporation/>
    <contributingCorporation/>
    <belongsToBibliography>0</belongsToBibliography>
    <completedDate>--</completedDate>
    <publishedDate>--</publishedDate>
    <thesisDateAccepted>--</thesisDateAccepted>
    <title language="deu">Untersuchungen an Elastomerdichtungen - Tieftemperatur und Alterung</title>
    <parentTitle language="deu">PolyMerTec 2014</parentTitle>
    <identifier type="old">33644</identifier>
    <enrichment key="eventName">PolyMerTec 2014</enrichment>
    <enrichment key="eventPlace">Merseburg, Germany</enrichment>
    <enrichment key="eventStart">2014-06-25</enrichment>
    <enrichment key="eventEnd">2014-06-27</enrichment>
    <enrichment key="InvitedTalks">0</enrichment>
    <author>Matthias Jaunich</author>
    <collection role="fulltextaccess" number="">Weder Datei noch physisches Exemplar vorhanden ("No Access")</collection>
    <collection role="literaturgattung" number="">Präsentation</collection>
  </doc>
  <doc>
    <id>26812</id>
    <completedYear/>
    <publishedYear>2012</publishedYear>
    <thesisYearAccepted/>
    <language>deu</language>
    <pageFirst/>
    <pageLast/>
    <pageNumber/>
    <edition/>
    <issue/>
    <volume/>
    <type>lecture</type>
    <publisherName/>
    <publisherPlace/>
    <creatingCorporation/>
    <contributingCorporation/>
    <belongsToBibliography>0</belongsToBibliography>
    <completedDate>--</completedDate>
    <publishedDate>--</publishedDate>
    <thesisDateAccepted>--</thesisDateAccepted>
    <title language="deu">Material behaviour of static seals at low temperatures</title>
    <parentTitle language="deu">17th ISC Stuttgart 2012</parentTitle>
    <identifier type="old">29594</identifier>
    <enrichment key="eventName">17th ISC Stuttgart 2012</enrichment>
    <enrichment key="eventPlace">Stuttgart, Germany</enrichment>
    <enrichment key="eventStart">2012-09-13</enrichment>
    <enrichment key="eventEnd">2012-09-14</enrichment>
    <enrichment key="InvitedTalks">0</enrichment>
    <author>Matthias Jaunich</author>
    <collection role="fulltextaccess" number="">Weder Datei noch physisches Exemplar vorhanden ("No Access")</collection>
    <collection role="literaturgattung" number="">Präsentation</collection>
  </doc>
  <doc>
    <id>35050</id>
    <completedYear/>
    <publishedYear>2015</publishedYear>
    <thesisYearAccepted/>
    <language>deu</language>
    <pageFirst>43</pageFirst>
    <pageLast/>
    <pageNumber/>
    <edition/>
    <issue/>
    <volume/>
    <type>conferenceobject</type>
    <publisherName/>
    <publisherPlace>Chemnitz</publisherPlace>
    <creatingCorporation>Technische Universität Chemnitz</creatingCorporation>
    <contributingCorporation/>
    <belongsToBibliography>0</belongsToBibliography>
    <completedDate>--</completedDate>
    <publishedDate>--</publishedDate>
    <thesisDateAccepted>--</thesisDateAccepted>
    <title language="deu">Alterung von Elastomerdichtungen für Lagerbehälter</title>
    <abstract language="deu">Unsere Aufgabe im Fachbereich 3.4 der Bundesanstalt für Materialforschung und  prüfung (BAM) ist die sicherheitstechnische Begutachtung von Transport- und Lagerbehältern für radioaktiven Abfall, die für langfristige Zwischenlagerung ausgelegt sind. Ein Arbeitsschwerpunkt ist die Bewertung der Lebensdauer von Metall- und Elastomerdichtungen in den Behältern im Hinblick auf die Anforderungen für langfristige Behältersicherheit (min. 40 Jahre in Deutschland). Um die Eigenschaftsänderungen der Elastomerdichtungen während einer beschleunigten Alterung über lange Zeiträume (bis zu fünf Jahre) untersuchen zu können, wurde ein Alterungsprogramm an ausgewählten Elastomeren (HNBR, EPDM, FKM) begonnen.&#13;
Im Gegensatz zu Normalterungsverfahren altern wir keine Normteile, sondern O-Ringe im unverpressten sowie verpressten Zustand. Diese Vorgehensweise ermöglicht die Bewertung des Einflusses der Verpressung auf die Alterung sowie die Untersuchung des Bauteilversagens mittels Leckageratenmessungen unter anwendungsnahen Bedingungen. Weitere Charakterisierungsmethoden sind Härtemessung, dynamisch-mechanische Analyse (DMA), Thermogravimetrie (TGA), Druckspannungsrelaxation, Druckverformungsrest (DVR), Dichtebestimmung und Zugversuch. Das Ziel ist, die Leckagerate mit anderen Eigenschaften bzw. Methoden zu korrelieren, um so ein aussagekräftiges und leichter zu bestimmendes Lebensdauerkriterium für elastomere O-Ringe abzuleiten. &#13;
Während der Alterung können in Abhängigkeit von Material sowie Alterungsdauer und –temperatur Inhomogenitäten aufgrund von diffusionsbegrenzter Oxidation auftreten, durch die sich unterschiedliche Eigenschaften an der Oberfläche und im Volumen der Dichtung ergeben, was zu falschen Lebensdauerabschätzungen führen kann. Mittels Mikrohärtemessung über den Querschnitt werden diese Effekte charakterisiert und bei der Extrapolation mittels Zeit-Temperatur-Verschiebung und Arrheniusgraph berücksichtigt. Bisher liegen Daten von bis zu einem Jahr bei vier verschiedenen Temperaturen (75 °C, 100 °C, 125 °C und 150 °C) gealterten Proben vor. Nach 100 Tagen bei 150 °C weisen HNBR und EPDM schon einen DVR von über 80 % auf, aber noch keinen signifikanten Anstieg der Leckagerate. Diese sinkt zunächst während der Alterung, da die Permeabilität aufgrund von Vernetzungsreaktionen sinkt. Bei HNBR ist dies aufgrund der dominanteren Vernetzungsreaktionen während der Alterung noch stärker ausgeprägt als bei EPDM.</abstract>
    <parentTitle language="deu">Technomer 2015 - 24. Fachtagung über Verarbeitung und Anwendung von Polymeren</parentTitle>
    <identifier type="old">38203</identifier>
    <identifier type="isbn">978-3-939382-12-6</identifier>
    <enrichment key="eventName">Technomer 2015 - 24. Fachtagung über Verarbeitung und Anwendung von Polymeren</enrichment>
    <enrichment key="eventPlace">Chemnitz, Germany</enrichment>
    <enrichment key="eventStart">12.11.2015</enrichment>
    <enrichment key="eventEnd">13.11.2015</enrichment>
    <author>Anja Kömmling</author>
    <author>Matthias Jaunich</author>
    <author>Dietmar Wolff</author>
    <subject>
      <language>deu</language>
      <type>uncontrolled</type>
      <value>Aging</value>
    </subject>
    <subject>
      <language>deu</language>
      <type>uncontrolled</type>
      <value>Elastomer</value>
    </subject>
    <subject>
      <language>deu</language>
      <type>uncontrolled</type>
      <value>Seal</value>
    </subject>
    <subject>
      <language>deu</language>
      <type>uncontrolled</type>
      <value>Leakage</value>
    </subject>
    <subject>
      <language>deu</language>
      <type>uncontrolled</type>
      <value>Compression</value>
    </subject>
    <collection role="literaturgattung" number="">Verlagsliteratur</collection>
    <collection role="fulltextaccess" number="">Datei im Netzwerk der BAM verfügbar ("Closed Access")</collection>
  </doc>
</export-example>
