Dokument-ID Dokumenttyp Autoren/innen Persönliche Herausgeber/innen Haupttitel Abstract Auflage Verlagsort Verlag Herausgeber (Institution) Erscheinungsjahr Titel des übergeordneten Werkes Jahrgang/Band ISBN Veranstaltung Veranstaltungsort Beginndatum der Veranstaltung Enddatum der Veranstaltung Ausgabe/Heft Erste Seite Letzte Seite URN DOI Lizenz Datum der Freischaltung OPUS4-44339 Vortrag Vogel, Christian Charakterisierung der P-Verfügbarkeit in Düngemitteln durch P-Senken Recycling-Düngemittel auf Basis von sekundären Ressourcen (Gülle, Gärreste, Klärschlamm, Tiermehl etc.) gewinnen in den letzten Jahren zunehmend an Bedeutung in der Landwirtschaft. Die in den Recycling-Düngemitteln enthaltenen P-Spezies weichen oft stark von denen in konventionell hergestellten Düngemitteln aus Rohphosphat ab, zudem enthalten Recyclingdünger oft mehrere verschiedene P-Formen. Die Pflanzenverfügbarkeit des P in ist ganz wesentlich von der enthaltenen P-Form abhängig. Derzeit gibt es außer zeitaufwendigen und kostspieligen Gefäß- und Feldversuchen keine zufriedenstellende Testmethode zur Analyse der P-Pflanzenverfügbarkeit von unterschiedlichen Recycling P-Düngemitteln. Die im europäischen Düngemittelrecht normierten chemischen Extraktionsmethoden (Wasser, Zitronensäure, Ameisensäure, neutral Ammoniumcitrat etc.) zeigen oftmals keine oder nur sehr geringe Korrelation zu der P-Aufnahme von Pflanzen in Gefäßversuchen mit Recycling-Düngemitteln (Kratz et al. 2010, Steckenmesser et al. 2017, Vogel et al. 2017). Eine grundlegende Schwäche chemischer Extraktionsmethoden liegt darin, dass es sich dabei um statische Methoden handelt, die nicht in der Lage sind, die im System Boden/Düngemittel-Bodenlösung-Pflanze stattfindenden dynamischen Prozesse wie P-Freisetzung und Entzug durch die Pflanzenwurzeln abzubilden. Einen Lösungsansatz bieten hier sog. P-Senken-Methoden. Bereits in den 1950er Jahren wurden erstmals P-Senken zur Analyse des Boden-P angewendet (Chardon et al. 1996). In den darauffolgenden Jahrzehnten wurden verschiedene P-Senken auf der Basis von Eisenoxid-Papier entwickelt (Chardon et al. 1996). Jedoch konnten diese Ansätze auch nur begrenzt zur Bestimmung der P-Pflanzenverfügbarkeit des Boden-P eingesetzt werden. Mitte der 1990er Jahre wurde die DGT (engl. diffusive gradients in thin films) Methode entwickelt (Zhang et al. 1998). Bei der DGT Methode diffundiert P aus der Bodenlösung des angefeuchteten Bodens durch einen Membranfilter und die Diffusionsschicht und wird anschließend an einer Bindungsschicht absorbiert. Durch den Diffusionsgradienten wird das Gleichgewicht in der Bodenlösung permanent gestört, wodurch auch labiles P im Boden gelöst wird. Die stetige Entnahme von P aus der Bodenlösung über die Diffusions-/Bindungsschicht simuliert dabei den Entzug von P durch die Pflanzenwurzel. Die an die Bindungsschicht adsorbierte Menge an P korreliert stark mit der P-Aufnahme von Pflanzen (u.a. Mason et al. 2005, 2013; Menzies et al. 2005, Six et al. 2012). Im Gegensatz zu chemischen Extraktionsmethoden werden bei der DGT Methode Mischungen an Düngemittel und Boden für mehrere Tage inkubiert (Vogel et al. 2017; Duboc et al. 2017), da ansonsten wasserlösliche P-Dünger den DGT Adsorber sättigen und wasserunlösliche P-Dünger unterschätzt werden. Ein bis zwei Wochen Inkubation sind ausreichend, damit sich pflanzenverfügbares P in die Mischungen bildet. In letzter Zeit haben verschiedene Forschungsgruppen gezeigt, dass die DGT Methode auch eine sehr gute Korrelation mit der Pflanzenverfügbarkeit verschiedener Typen von (Recycling-)P-Düngemitteln aufweist (Vogel et al. 2017; Duboc et al. 2017; Foereid 2017; Haarstad and Bavor 2017; Lemming et al. 2017). Bei Gefäßversuchen mit verschiedenen Recycling P-Düngemitteln konnte die DGT Methode den Ertrag bzw. die P-Aufnahme von Mais deutlich besser vorhersagen als herkömmliche chemische Extraktionsmethoden (Vogel et al. 2017; Duboc et al. 2017). Daher kann die DGT Methode im Vorfeld der Zulassung von neuen Düngermitteltypen als zuverlässige und robuste Methode zum Screening von Produktvarianten eines Düngemittelherstellers verwendet werden. Um dieses Messverfahren im Rahmen des Düngemittelrechts als Bewertungsinstrument für die Abschätzung der Pflanzenverfügbarkeit unterschiedlicher Düngemittel zu verwenden, muss es allerdings zunächst standardisiert werden. Zu diesem Zweck bietet sich der Einsatz eines „standardisierten" Bodens bzw. Bodenrezepts an. Zur Kalibrierung der Methode im jeweiligen Labor könnten auch chemisch definierte P-Verbindungen mit bekannter Löslichkeit/Pflanzenverfügbarkeit als Referenz-substanzen verwendet werden. 2018 Fachgespräch Recycling-Phosphate als Düngemittel für die Landwirtschaft Bonn, Germany 14.02.2018 15.02.2018 2018-03-02 OPUS4-44178 Vortrag Adam, Christian Chemische Charakterisierung von P-Recyclaten Zukünftig werden vermehrt P-Recyclate auf den Düngemittelmarkt kommen. Diese müssen ausreichend charakterisiert werden, um Sicherheit und Wirksamkeit beurteilen zu können. Mit dem Vortrag wurde der wissenschaftliche Beirat für Düngungsfragen des Bundesministeriums für Ernährung und Landwirtschaft beraten. 2018 Fachgespräch Recycling-Phosphate als Düngemittel für die Landwirtschaft Bonn, Germany 14.02.2018 15.02.2018 2018-02-16 OPUS4-45341 Zeitschriftenartikel Steckenmesser, D.; Vogel, Christian; Böhm, L.; Heyde, B.; Adam, Christian Fate of heavy metals and polycyclic aromatic hydrocarbons (PAH) in sewage sludge carbonisates and ashes - A risk assessment to a thermochemical phosphorus-recycling process In the near future, phosphorus (P) recycling will gain importance in terms of decreasing primary resources. Sewage sludge (SSL) is an adequate secondary P-resource for P-fertilizer production but it is also a sink for heavy metals and organic pollutants. The present study is an investigation on thermochemical P-recycling of SSL. Various temperatures and amendments were tested regarding their performance to remove heavy metals and polycyclic aromatic hydrocarbons (PAH) and simultaneous increase of the plant-availability of P. The investigations were carried out on two types of SSL originating from wastewater treatment plants with chemical P-precipitation and enhanced biological P-removal, respectively. The results show that thermochemical treatment with chlorine donors is suitable to remove the majority of heavy metals and that a combination of a gaseous chlorine donor (HCl) and sodium additives leads to both high heavy metal removal and high plant availability of P. Furthermore, plant experiments Show that almost all investigated thermochemical treatments can significantly reduce the bioavailability and plant uptake of heavy metals. Furthermore, PAHs are secondarily formed during low-temperature treatments (400-500 ° ), but can be significantly reduced by using sodium carbonate as an additive. Amsterdam Elsevier Ltd. 2018 Waste Management 78 576 587 10.1016/j.wasman.2018.06.027 2018-07-03 OPUS4-44481 Zeitschriftenartikel Huber, F.; Herzel, Hannes; Adam, Christian; Mallow, O.; Blasenbauer, D.; Fellner, J. Combined disc pelletisation and thermal treatment of MSWI fly ash An environmentally friendly and cost efficient way for the management of municipal solid waste incineration (MSWI) fly ash represents its thermal co-treatment together with combustible waste. However, the safe introduction and storage of MSWI fly ash in the waste bunker is challenging and associated with severe problems (e.g. dust emissions, generation of undefined lumps and heat in case of moistened MSWI fly ash). Therefore, the aim of this study is to investigate the suitability of pelletisation as a pretreatment of MSWI fly ash. In particular, MSWI fly ash was characterised after sampling, pelletisation and thermal treatment and the transfer of constituents to secondary fly ash and flue gas was investigated. For this purpose, MSWI fly ash pellets with a water content of about 0.15 kg/kg and a diameter of about 8 mm have been produced by disc pelletiser and treated in an electrically heated pilot-scale rotary kiln at different temperatures, ranging from 450°C to 1050°C. The total contents of selected elements in the MSWI fly ash before and after thermal treatment and in the generated secondary fly ash have been analysed in order to understand the fate of each element. Furthermore, leachable contents of selected elements and total content of persistent organic pollutants of the thermally treated MSWI fly ash were determined. Due to the low total content of Hg (0.7 mg/kg) and the low leachate content of Pb (<0.36 mg/kg), even at the lowest treatment temperature of 450°C, thermally treated MSWI fly ash pellets can be classified as nonhazardous waste. However, temperatures of at least 650°C are necessary to decrease the toxic equivalency of PCDD/F and DL-PCB. The removal of toxic heavy metals like Cd and Pb is significantly improved at temperatures of 850°C, 950°C or even 1050°C. The observed metal removal led to relatively high contents of e.g. Cu (up to 11,000 mg/kg), Pb (up to 91,000 mg/kg) and Zn (up to 21,000 mg/kg) in the secondary fly ash. This metal enriched secondary fly ash might represent a potential raw material for metal recovery (e.g. via acidic leaching). Due to the high content of total dissolved solids observed in the leachate of thermally treated MSWI fly ash pellets, a wet extraction procedure is suggested to enable its safe disposal at non-hazardous waste landfills. Rotterdam Elsevier Ltd. 2018 Waste Management 73 381 391 10.1016/j.wasman.2017.12.020 2018-03-19 OPUS4-45221 Vortrag Adamczyk, Burkart Nachbehandlung von Stahlwerksschlacke und deren Verwertung als Klinkermaterial LD-Schlacken weisen eine große chemische Ähnlichkeit zu Protlandzementklinker auf. Sie enthalten jedoch noch bis zu 30% Eisen, das mineralisch in oxidischer Form gebunden vorliegt. Dadurch kann sich bei der Erstarrung die wichtigste Klinkerphase "Alit" nicht ausbilden. Durch eine reduzierende Schmelzbehandlung der Schlacke kann des mineralisch gebundene Eisen als Metall separiert werden. Dadurch wird auch die Mineralogie der Schlacke so verändert, dass auch sie nun praktisch einem Portlandzementklinker entspricht. Entsprechende Versuche wurden am kleintechnischen Lichtbogenofen der BAM durchgeführt. Es werden Ergebnisse vorgestellt und auf Grenzen und Möglichkeiten eines derartigen Prozesses im Hinblick auf eine industrielle Umsetzung eingegangen. 2018 Berliner Konferenz "Mineralische Nebenprodukte und Abfälle" Berlin, Germany 11.06.2018 12.06.2018 2018-06-19 OPUS4-45199 Beitrag zu einem Tagungsband Adamczyk, Burkart; Schraut, Katharina; Adam, Christian Thiel, S.; Thomé-Kozmiensky, E.; Friedrich, B.; Pretz, T.; Quicker, P.; Senk, D. G.; Wortruba, H. Nachbehandlung von Stahlwerksschlacken und deren Verwertung als Klinkermaterial Steelmaking slags produced using the Linz-Donawitz method (LD slags) are widely used as building and construction materials in road, earth and water works. Because the legal conditions become more and more re-strictive , this application is uncertain in the future. LD slags contain high amounts of mineral bound iron (in form of Fe2O3), which must be considered as a waste of resources. Except for the Iron the chemical composition is quite similar to that of Portland cement clinker. However, due to the high content of Fe2O3 the mineralogical composition differs significantly, resulting in a low hydraulic reactivity. A post-treatment of the liquid LD slag in an electric arc furnace under reducing conditions enables the reduction of the iron compounds to metallic iron, which separates from the mineral phase due to its higher density. The remaining solidified mineral fraction mainly contains typical crystalline phases of cement clinker in similar ratios: Alite (Ca3SiO5; > 60%) as main phase, Belite (Ca2SiO4, 10%), Tricalciumaluminate (Ca3Al2O6; 5%) and Brownmillerite (Ca2(Al,Fe)2O5, 1%) as secondary phases. Alite, which usually decomposes to Belite and free lime under slow cooling conditions, is stabilized in the Fe-reduced slag probably by integration of foreign ions into the lattice and is stable even if the slag is cooled down very slowly. Furthermore, the particularly large Alite crystals do not exhibit the typical decomposition edge of Belite and lime, found in Alite from ordinary ce-ment clinker. Technological tests for building materials show a high hydraulic reactivity and a compressive strength after 28 days comparable or even slightly higher to reference cement. Nevertheless, because of the increasing viscosity with decreasing Fe2O3 content, the treatment requires a temperature higher than the slag decanted from the LD converter. Furthermore, during the reduction of the bound Iron huge amounts of carbon monoxide are released, resulting in foaming of the slag. Both aspects make it difficult to manage the process. In addition, for economic reasons the treatment has to be carried out immediately after casting the slag from the LD converter to avoid the solidification, which is a logistical challenge for most steel plants. Otherwise the separation of the mineral bound iron as metallic phase and the utilisation of the mineral fraction as cement clinker will both save resources and lower the global CO2-output. For these reasons further initiatives should be considered in the medium term. Neuruppin Thomé-Kozmiensky Verlag GmbH 2018 Mineralische Nebenprodukte und Abfälle 5 5 978-3-944310-41-1 Berliner Konferenz Mineralische Nebenprodukte und Abfälle Berlin, Germany 11.06.2018 12.06.2018 282 296 2018-06-20 OPUS4-45612 Vortrag Taube, Mareike Carolin Optimierung eines pyrometallurgischen Tantal- und Niob- Recyclingprozesses mithilfe von On-Line LIBS Die Entwicklung von Hochleistungselektronik zu immer kleineren Bauformen ohne Leistungseinbußen ist ohne den Einsatz von Technologiemetallen wie Niob und Tantal heute praktisch nicht mehr realisierbar. Besonders in technischen Geräten wie Smartphones und Tablets sind Tantal- und Niobkondensatoren aufgrund ihrer hohen Leistungsdichten bereits unverzichtbar geworden. Für die nachhaltige Produktion von Elektronik stellt jedoch vor allem das Tantalerz Coltan als sogenanntes „conflict mineral" ein großes Problem dar. Um den Wirtschaftsstandort Europa unabhängiger von Primärrohstoffimporten aus Krisenregionen zu machen, ist die Entwicklung von effizienten Recyclingverfahren heute wichtiger denn je. An der Bundesanstalt für Materialforschung und -prüfung (BAM) findet daher zurzeit die Optimierung eines pyrometallurgischen Industrieprozesses zur Niob- und Tantalrückgewinnung statt, welchem hauptsächlich niedrigkonzentrierte metallurgische Rückstände aus der Tantal- und Niob- bzw. der Zinngewinnung als Einsatzstoffe dienen. Zu diesem Zweck werden im kleintechnischen Lichtbogenofen der BAM (480 kVA, max. Materialdurchsatz ca. 150 kg/h) Versuche mit einem neuen innovativen Messgerät durchgeführt, welches eine On-Line Analyse von Hochtemperaturprozessen ermöglicht. Der eingesetzte Prototyp nutzt das Verfahren der laserinduzierten Plasmaspektroskopie (LIBS), um die chemische Zusammensetzung der Schlackephase noch im Schmelzbad und während eines Schlackeabgusses zu bestimmen. Nach einer Kalibrierung auf das vorliegende Stoffsystem ermöglicht dieser On-Line-LIBS Prototyp der BAM daher eine in-situ Bestimmung der Elementverteilung in der Schmelze. Die hier gewonnenen Daten sollen helfen, die aktuelle Prozessführung zu verbessern und die Tantal- und Niobausbeute noch weiter zu erhöhen. 2018 Jahrestreffen Bremen 2018 der ProcessNet-Fachgruppen Hochtemperaturtechnik (HTT), Abfallbehandlung und Wertstoffrückgewinnung (AuW) Bremen, Germany 06.03.2018 07.03.2018 2018-08-01 OPUS4-45614 Vortrag Taube, Mareike Carolin Optimisation of a Pyrometallurgical Niobium and Tantalum Recyling Process with on-line-LIBS Tantalum and niobium are essential for the development of electronics towards a more and more compact design, but without reducing their performance today. Especially in smart phones and tablets, tantalum and niobium capacitors with high charge densities have already become almost indispensable. However, tantalum as a critical raw material is still a problem for the sustainable production of electronics. Due to this fact, the existence of efficient recycling processes especially in Europe is becoming even more important nowadays. The Bundesanstalt für Materialforschung und -prüfung (BAM) is currently working on the optimisation of an existing pyrometallurgical tantalum recycling process. Optimisation of this industrial process is carried out in a small-scale electric arc furnace (480 kVA, capacity approx. 150 kg/h) at BAM using a new and innovative equipment for on-line analysis of high temperature processes. The aim of this project is to identify the best timing for an optimum slag tapping, when the slag is lower than minimum targeted tantalum concentration. Hence, LIBS (Laser induced breakdown spectroscopy) is used to identify the chemical composition of the slag layer and during slag tapping. The on-line-LIBS prototype of BAM enables an in-situ measurement of the element distribution in the melt after calibration on the slag system. First results of this joint research project will be presented including on-line-LIBS-measurements and thermodynamic and kinetic aspects of the process. 2018 European Mineral Processing & Recycling Congress (EMPRC 2018) Essen, Germany 25.06.2018 26.06.2018 2018-08-01 OPUS4-45679 Buchkapitel Adam, Christian; Krüger, Oliver IWA Publishing, Wastewater as a resource: From rare earth metals to phosphorus Wastewater contains a diverse array of organic and inorganic compounds and its complex composition strongly depends on the location and the connected dischargers. However, municipal wastewater as a carrier of feces and urine generally contains considerable amounts of the main nutrients nitrogen and phosphorus. The latter is in the focus of the discussions about the recovery potential of wastewater due to the relatively high mass flows of phosphorus in wastewater and the finite nature and decreasing quality of phosphate rock reserves. But due to the presence of the whole periodic table of elements, wastewater might contain further valuable components of interest for recovery including those defined as critical raw materials by the European Commission. Phosphorus and most of the other critical raw materials are fixed in the sewage sludge and after incineration in the sewage sludge ash (SSA). This is accompanied by high concentration factors from wastewater via sludge to ash. However, the mass fractions of the majority of elements in sewage sludge are comparable to those of the earth crust, indicating no relative enrichment. Nevertheless, enrichment factors of 100 or higher are given for phosphorus, copper, zinc, cadmium, silver, tin, lead and the platinum group elements indicating an anthropogenic input. An economic value of sewage sludge was estimated to $460,-/t calculated on the basis of the respective market prices for high purity elements - a theoretical value. A German survey of sewage sludge ashes showed that the mass fractions and the mass flows of most of the elements present in SSA are probably too low for an economic recovery. In most cases the mass flows are rather small compared to the imports and the chemical forms are not suitable for recovery. An exception is phosphorus that is present in high mass fractions up to 13% and that bears a high substitution potential. If the application of P-recovery technologies lead to a further concentration of valuable elements e.g. as by-products in side streams of the process, it would probably make also the recovery of other elements of economic interest. London IWA Publishing 2018 Phosphorus: Polluter and Resource of the Future 978-1-78040-835-4 241 252 10.2166/9781780408361 2018-08-09 OPUS4-48078 Beitrag zu einem Tagungsband Weimann, Karin; Adam, Christian Martins, I. M.; Ulsen, C.; Villagran, Y. Advantages of recycling gypsum plasterboards Advantages of recycling gypsum plaster boards During the last decades the material composition of buildings has become increasingly diverse. However, largely sorted material flows are needed for generating high quality secondary building materials. The use of secondary building materials can meet the requirements of sustainability in several ways: the extended time availability of primary raw materials and, thereby, the preservation of natural resources as well as the conservation of landfill sites. Recycling of gypsum (calcium sulfate) can be a good example for the environmental benefits of closed-loop recycling. The content of sulfates in other secondary building materials, in particular in recycled concrete aggregates, should be minimized for quality reasons. In contrast, separated gypsum can also be used in gypsum production if the high quality requirements for the recycled gypsum are met. Since almost all processing steps in the recycling process are associated with environmental impacts, an environmental evaluation of the use of recycled gypsum as a substitute in gypsum production has to be carefully conducted. This paper focusses on the techniques for generating recycled gypsum from gypsum plasterboards, the related quality requirements and a comprehensive environmental evaluation of the complete process. Paris Rilem publications S.A.R.L. RILEM 2018 Progress of Recycling in the Built Environment PRO 124 978-2-35158-208-4 IV International Conference Progress of Recycling in the Built Environment Lisbon, Portugal 11.10.2018 12.10.2018 243 250 2019-05-29