TY - THES A1 - Shcheglov, Pavel T1 - Study of Vapour-Plasma Plume during High Power Fiber Laser Beam Influence on Metals N2 - Die wichtigsten Ergebnisse der Dissertation sind: 1. Experimentelle Untersuchungen der Dampf-Plasma-Fackel wurden beim Schweißen von niedriglegierten Stählen großer Blechdicke unter Einsatz der Strahlung eines Hochleistungsfaserlasers (10÷20 kW) durchgeführt. 2. Experimentell wurde festgestellt, dass die Temperatur sowie die Volumenkonzentration der freien Elektronen im laserinduzierten Schweißplasma vernachlässigbar gering sind (Т < 4500 К, n < 1015e cm -3). 3. Es wurde gezeigt, dass neben dem Schweißplasma, das mit einem relativ kleinen Volumen (5-10 mm) nahe der Metalloberfläche entsteht, die Schweißfackel einen größeren Teil (bis 60-70 mm) im oberen Bereich einnimmt, welcher aus der Wolke der kleinen Partikel aus kondensiertem Metalldampf besteht und die Laserstrahlung absorbieren kann. 4. Die experimentell gemessene durchschnittliche Größe der kondensierten Metallpartikel in der Schweißfackel beträgt je nach Fackelhöhe bzw. Schweißprozessparameter 80 nm bis 110 nm. Die Volumenkonzentration der Partikel in der Wolke an der Fackelachse beträgt ca. 1010 cm-3. 5. Die Extinktion der Prüfstrahlung im oberen Teil der Schweißfackel wird zum großen Teil von der Absorption der kleinen kondensierten Partikel verursacht. Der experimentell gemessene Extinktionskoeffizient für eine Prüfstrahlungswellenlänge von 1.3 μm hatte einen Wert von etwa einigen m-1 und ist damit wesentlich größer als der Koeffizient der inversen Bremsstrahlungsabsorption im Schweißplasma. 6. Schutzgaszufuhr (Ar, He) beim Schweißprozess führt zur effektiven Abkühlung des Schweißplasmas im unteren Teil der Fackel bis zur vollen Unterdrückung. Infolge des intensiveren Kondensationsprozesses über der Dampfkapillare kann aber dabei der Einfluss des oberen Teiles noch stärker werden. 7. Die Gesamtleistungsabschwächung des Hochleistungsfaserlaserstrahls, der durch die Schweißfackel zur Metalloberfläche gelangt, kann variierend einen Wert von bis zu 10% haben. Mit Rücksicht auf die zeitliche Dynamik kann dieser Effekt zu einer erheblichen Verschlechterung der Leistungsstabilität der Laserstrahlung führen, die den Dampfkapillareeingang erreicht. N2 - The most important results of the dissertation are: 1. Systematic experimental investigations of the vapour-plasma plume generated during deep penetration high-power (10÷20 kW) ytterbium fiber laser beamwelding of low-alloyed mild steel plates were carried out. 2. It was confirmed experimentally that free electron temperature and concentration in the laser- induced welding plasma plume are negligibly low (Т < 4500 К,ne < 10 15 cm-3). On the basis of these values it can be affirmed that absorption and refraction of high power fiber laser radiation in the welding plasma plume are not able to influence the welding quality in this case. 3. It was shown that the vapour-plasma welding plume is composed of the welding plasma generated in a relatively small area (5-10 mm height) near the metal surface and of an extensive upper part (up to 60-70 mm height) which consists of a small condensed metal vapour particle cloud and is able to absorb electromagnetic radiation. 4. Average condensed metal vapour particle diameter in the welding plume was measured experimentally to vary from 80 nm to 110 nm depending on the welding plume height as well as on the welding process parameters. Volume particle concentration in the cloud on the welding plume axis has a value of about 1010 cm-3. 5. Extinction of the probe laser radiation in the upper part of the welding plume is mainly caused by absorption in the small condensed metal vapour particles. The extinction coefficient at the probe radiation wavelength of 1.3 μm was measured experimentally to have a value of about a few units per meter which is much higher than the inverse Bremsstrahlung absorption coefficient in the welding plasma plume calculated for this radiation wavelength. 6. Shielding gas (Ar or He) supplied to the welding area leads to intensive cooling of the welding plasma in the lower part of the welding plume down to its complete suppression. However, due to the more intensive metal vapour condensation process in the colder medium above the keyhole, the upper part influence can become even stronger. 7. Total attenuation of the high-power fiber laser beam propagating through the whole welding plume height to the metal surface was estimated to be about 10%. Considering the spatial dynamics of the probe light extinction signals it was concluded that the effect of metal vapour condensation over the keyhole during deep penetration high-power fiber laser metal welding is able to significantly worsen of the laser beam power stability when the beam reaches the keyhole inlet. T3 - BAM Dissertationsreihe - 88 KW - Particle diagnostics KW - Plume KW - Plasma diagnostics KW - Laser welding KW - Vapour condensation PY - 2012 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-703 SN - 978-3-9815134-3-1 SN - 1613-4249 VL - 88 SP - 1 EP - 125 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin AN - OPUS4-70 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -