Refine
Document Type
Language
- English (7)
Keywords
- Adsorption (2)
- Sintering (2)
- Alumina (1)
- Austenization (1)
- Bio-tribocorrosion (1)
- Biomaterial (1)
- Biomaterials (1)
- Biomedical applications (1)
- Corrosion (1)
- Dehydrated/rehydrated kaolin (1)
Institute
The recovery of surfactants from organic mediums is of great economic and environmental interests in the field of petrochemicals sector. The aim of this study was to recover poly-dispersed nonionic surfactant (TX-100) from organic medium by the use of dehydrated and rehydrated kaolin. It was found that the presence of water after kaolin rehydration decreases considerably the amount of TX-100 adsorption from 28.7 μmol.g−1 onto dehydrated kaolin to 23.4 μmol.g−1 onto rehydrated kaolin. The estimation of the number of statistical layers of water deposited on kaolin was observed to be about 7 to 9. The effect of type of solvents (heptane, cyclohexane and benzene) on the adsorption onto rehydrated kaolin revealed a reduction in the adsorbed quantity; the adsorbed amounts were found to be 28.7 μmol.g−1, 26.7 μmol.g−1 and 24.2 μmol.g−1 in heptane, cycloheptane and benzene phases, respectively. On the other hand, it was observed that a temperature increased from 20 °C to 35 °C and 45 °C negatively affects the adsorption of TX-100 onto dehydrated and/or hydrated kaolin in heptane medium.
The hydrophilic-hydrophobic surface area of alumina powder (Al₂O₃) oxidized at different temperatures was determined on the base of adsorption of water and butane vapor at 25°C. In the order to study the influence of thermal oxidation upon hydrophilic/hydrophobic character of the surface, samples of Al₂O₃ were characterized using granulometry, SEM and BET surface area measurement. SEM results showed that the thermal treatment does not affect the morphology of the Alunima. However, the increase of treatment temperature from 250 to 900°C results in changing of the hydrophilic-hydrophobic balance of Al₂O₃ surface.
The bio-tribocorrosion behavior of newly developed near β-types Ti-15Nb and Ti-15Mo alloys was investigated in Phosphate-Buffered Saline (PBS) under different loads. Open-Circuit Potential (OCP), friction coefficient, wear volume and wear rate were evaluated. The results revealed that Ti-15Nb alloy exhibited lower wear rate, lower friction coefficient and better corrosion resistance during tribocorrosion than the Ti-15Mo alloy. This can be attributed to the diffusion of Nb which increases the repassivation rate (formation of a protective layer) in the Ti-15Nb alloy. In contrast Ti-15Mo shows a significantly higher rate of chemical reaction.
Low modulus β-type Ti-15Nb alloys were prepared by subjecting them to different sintering temperatures (800, 900, 1000 and 1100 °C) and their morphological and structural properties were evaluated. X-ray diffraction analysis was used for the morphological characterization which indicated that the mean pore and crystallite size continuously decreased with increasing sintering temperature to reach the lowest values of 41 nm and 27.5 nm at 1100 °C, respectively. Moreover, the higher sintering temperature resulted in higher relative density, greater hardness and young’s modulus of the Ti-15Nb alloys. Wear tests were conducted using a ball-on-plate type Oscillating tribometer, under different applied loads (2, 8 and 16 N) to evaluate their tribological characterization. The wear rate and friction coefficient were lower at higher sintering temperature. This enhancement in tribological properties was attributed to a grain refinement. The Ti-15Nb alloys sintered at 1100 °C showed the best tribological performance.
Ti–Ni powder compacts were prepared by mechanical alloying (MA), followed by hot isostatic pressing (HIP). Afterwards, the samples were sintered at different temperatures (950, 1050, 1150 and 1250 °C). Microhardness, density, crystallite size as well as microstrain of the sintered samples were measured and analyzed. Wear characteristics in phosphate-buffered saline (PBS) solution was tested under different applied loads of 2 N, 10 N, and 20 N, respectively. The results indicated that the crystallite size continuously decreases with increasing sintering temperature and reaches the lowest value of 31.3 nm at 1250 °C. The relative density of the sample sintered at 1250 °C is 98.0%. Moreover, the higher sintering temperatures lead to the higher relative density and the increase in hardness and young’s modulus of the sample. At the same time the friction coefficient and wear rate were lower for the samples sintered at 1250 °C. This improvement in friction and wear resistance is attributed to the grain size refinement. Ti–Ni sintered at 1250 °C showed good tribological performance under all test conditions.
The aim of this study was to investigate the influence of thermo-cyclic treatments on the mechanical characteristics (Hardness and Resilience) of low-alloy 42CD4 steel. Thermocyclic treatment on 42CD4 steel was operated for four cycles at 850 °C for 30 min. After each cycle, the steel sample was cooled in different medium (open air and water) in order to check the effect of the cooling rate on the microstructure characteristics. It was found that the cooling rate can affect the mechanical characteristics of the steel. The hardness values of steel cooled in water were higher than those of steel cooled in air. Additionally, there was an increase in the resilience of steel sample with the increase of thermocyclic number.
Implant-related follow up complications resulting from poor implant integration, delamination, chipping, mechanical instability, inflammation or graft-vs-host reaction may lead to low patient tolerance, prolonged care and sometimes leading to a second surgery. Hence, there is an urgent need for developing biomaterials which will help to overcome the above compatibility problems. Ti based alloys have been widely used for biomedical applications, due to their excellent properties, such as low modulus, high biocompatibility and high corrosion resistance. In order to further improve the physical, mechanical and tribological properties of these alloys, microstructural modification is often required. Hence, this study aims to develop and evaluate the structural and tribological behavior of Hot Isostatic Pressed (HIPed) and sintered Ti-6Al-7Nb samples containing niobium, which is less toxic and less expensive as compared to the usual alloying element, vanadium (Ti-6Al-4 V). The Ti-6Al-7Nb alloys were fabricated by using nanoparticle powders milled for different durations (2, 6, 12 and 18 h) to evaluate the effect of milling time on the morphological and structural properties. Friction and wear tests were carried out on the (HIPed) and finally sintered Ti-6Al-7Nb alloy samples, to evaluate their tribological properties under different applied loads (2, 8 and 16 N), with an alumina α-Al2O3 ball as a counter face using an oscillating tribometer. The physical characterization of the nanopowders formed using different milling times indicated that the particle and crystallite size continually decreased with increasing milling time, while the microstrain increased. It is observed that the friction coefficient and wear rate for the samples prepared by powders milled for 18 h and tested under 2 N were lowest with values of 0.25 and 1.51 × 10−2 μm3∙N-1 μm-1, respectively compared to other milled samples. This improvement in tribological properties is attributed to the grain refinement at high milling times. The antibacterial evaluation of the fabricated alloys showed an improvement in antibacterial performance of the samples milled at 18 h compared to the other milling times.