TY - CHAP A1 - Simon, Sylvio A1 - Engel, Sebastian A1 - Russig, Martin T1 - Fertigung lamellierter Werkzeuge mittels Wasserstrahlschneiden T2 - Tagungsband, 12. Wissenschaftstage der Hochschule Lausitz, 28. - 30. November 2012 KW - Wasserstrahlschneiden Y1 - 2012 SN - 3-9810211-5-0 PB - Hochschule Lausitz CY - Senftenberg ER - TY - CHAP A1 - Simon, Sylvio T1 - RFID basierte Produktkennzeichnung und mögliche Verbesserungen im Instandhaltungsprozess in der Montanindustrie T2 - Tagungsband, 12. Wissenschaftstage der Hochschule Lausitz, 28. - 30. November 2012 Y1 - 2012 SN - 3-9810211-5-0 PB - Hochschule Lausitz CY - Senftenberg ER - TY - GEN A1 - Amirov, Fariz A1 - Shiraliyev, Ilgar ED - Simon, Sylvio T1 - Research on wear and tear of the mud pump liners T2 - Conference Proceedings of the 4th International Conference on Energy Supply and Energy Efficiency and "5 Years NESEFF", 28 Sep – 04 Okt 2020 N2 - The article tells about the research on wear and tear of mud pump liners, namely: main characteristics that distinguish ceramic liner from the other ones used on the units equipped with the hydraulic system for washing out the drilling wells from cuttings, design of ceramic liners, calculation of the wear rate of ceramic liners, and the positive contribution they made on the modern drilling process. Besides, the research is made on the simplicity of the structure of ceramic liners, a short amount of time consumed to assemble and replace the liners, safety of the work, cost-effectiveness, wearing and corrosion durability, and also compliance with other requirements. Y1 - 2020 SN - 978-3-940471-59-8 SP - 65 EP - 66 CY - Cottbus ER - TY - GEN A1 - Simon, Sylvio A1 - Fraňa, Karel A1 - Neubert, Christian A1 - Mammadov, Arastun A1 - Amirov, Fariz ED - Atluri, Satya N. ED - Vušanović, Igor T1 - A Flow Study in the Cyclone with Particle Separations T2 - Computational and Experimental Simulations in Engineering, Proceedings of ICCES 2020. Volume 1 N2 - Unsteady turbulent flows with solid particles of different sizes in the cyclone were studied numerically and experimentally. The grid studies and influence of the boundary condition prescription on the flow behavior in the cyclone and the effectiveness of the particle separation were studied firstly numerically. The turbulent flow was calculated by means of Large Eddy Simulations and this flow problem was calculated parallel using eight processors. It was found theoretically that pressure at the bottom outlet of the cyclone has a significant impact on the particle separation. This impact of the pressure at the cyclone function was examined also using experiments and pressure distributions for different flow rate intensities for several locations in the cyclone were determined. These experimental results can be used for a validation of numerical results. Furthermore, the larger losses were observed in the immersion tube due to higher flow velocity and impulse exchange in the vortex core. KW - Cyclone flows KW - Particle separations KW - Pressure distributions Y1 - 2020 SN - 978-3-030-64689-9 SN - 978-3-030-64690-5 U6 - https://doi.org/10.1007/978-3-030-64690-5_6 SN - 2211-0984 SN - 2211-0992 VL - Mechanisms and Machine Science SP - 52 EP - 59 PB - Springer CY - Cham ET - 1. Auflage ER - TY - GEN A1 - Amirov, Fariz A1 - Shiraliyev, Ilgar T1 - Reducing maintenance costs by increasing the service life of mud pump ceramic liners T2 - Oil Gas European Magazine · August 2022, DVV Media Group GmbH, Deutschland N2 - The article tells about the research on wear and tear of mud pump liners, namely: main characteristics that distinguish ceramic liners from others used on the units equipped with a hydraulic system for washing out the drilling wells from cuttings, design of ceramic liners, calculation of the wear rate of ceramic liners, and the positive contribution they have made on the modern drilling process. Besides, the research is made on the simplicity of the structure of ceramic liners, little time required to assemble and replace the liners, safety of the work, cost-effectiveness, wearing and corrosion durability, and also compliance with other requirements. Y1 - 2022 U6 - https://doi.org/10.19225/220204 SN - 0179-3187 IS - 2 SP - 32 EP - 34 ER - TY - GEN A1 - Amirli, Samir A1 - Fritzsche, Pascal A1 - Abbasov, Ilgar A1 - Wichmann, Steffen A1 - Simon, Sylvio A1 - Amirov, Fariz A1 - Mammadov, Arastun T1 - The İmpact of High Speed Mechanical Processing Efficiency on the Production Process T1 - Влияние высокоскоростной механической обработки на производственный процесс T2 - HERALD of the Azerbaijan Engineering Academy N2 - The main purpose of the article is to increase productivitiy, reduce processing time and the same time increase the cutting speed. The results are also displayed in Excel using a number of cutting parameters. For this purpose, the article shows the results of both high-speed milling and high-speed turning of a machine with different types of tools, as well as processing of one tool on different types of machines. Unlike other machines, in general, the work on the machines of universal processing centers turned out to be more productive. The feed rate of the machine tools is the focus area here. If we increase cutting values, then the tool life is reduced and that leads to higher tool costs. With universal high-performance machines we cannot save costs for tools (we can only save machine tool costs). Compared to universal high-performance machines, we can save tool costs with Universal Machining Center. Therefore, it is suggested to the machining with the universal machining center, although the machining time and cutting time is faster with the universal high-performance machine. N2 - В статье показаны результаты как высокоскоростной фрезерной, так и высокоскоростной токарной обработки станка с разными типами инструментов, а также обработки одного инструмента на разных типах станков. В отличие от других станков, работа на станках универсальных обрабатывающих центров оказалась более производительной. В центре внимания здесь скорости подачи станков. Если мы увеличиваем параметры резания, то срок службы инструмента снижается, что приводит к увеличению затрат на инструмент. С универсальными высокопроизводительными станками мы не можем сэкономить на инструментах (мы можем сэкономить только на станках). По сравнению с универсальными высокопроизводительными станками, мы можем сэкономить на инструментальных средствах с помощью универсального обрабатывающего центра. Поэтому рекомендуется выполнять обработку на универсальном обрабатывающем центре, хотя время обработки и время резки меньше на универсальном высокопроизводительном станке. KW - Energy efficiency KW - High speed mechanical processing KW - Production KW - Neseff Y1 - 2022 U6 - https://doi.org/10.52171/2076-0515_2022_14_01_41_51 SN - 2076-0515 SN - 2789-8245 VL - 14 IS - 1 SP - 41 EP - 51 ER - TY - GEN A1 - Amirov, Fariz A1 - Simon, Sylvio A1 - Wichmann, Steffen A1 - Amirli, Samir A1 - Fraňa, Karel T1 - Determining the Accuracy of Water Pressure Processing using 3D Scanning T1 - Определение точности измерений при обработке давлением воды с использованием 3D-сканирования T2 - HERALD of the Azerbaijan Engineering Academy N2 - The article provides the results of the study of manufacturing tolerances in waterjet cutting by the method of three-dimensional (3D) measurements: shape deviations were shown by three-dimensional comparison of scanned samples. The dimensions were also measured using two-dimensional (2D) sections of the scanned samples. It has been determined that the clean waterjet cutting tends to separate soft materials such as plastic, foil, foam or paper, as well as food. Unlike the pure waterjet cutting, the abrasive cutting is used for hard materials such as steel, ceramics, glass. The optimal pressure for material processing has been calculated. Particular emphasis is placed on the separation of composite materials, which cannot be satisfactorily accomplished using conventional methods. N2 - В статье приведены результаты исследования производственных допусков при водоструйной резке методом трехмерных (3D) измерений: отклонения формы были показаны путем трехмерного справнения отсканированных образцов. Размеры были измерены также с использованием двухмерных (2D) срезов отсканированных образцов. Определено, что чистая водоструйная резка имеет тенденцию отделять мягкие материалы, такие как пластмасса, фольга, пена или бумага, а также пища. В отличие от чистой водоструйной резки, абразивная резка используется для твердых материалов, таких как сталь, керамика, стекло. Вычислено оптимальное давление для обработки материалов. Особое значение уделено разделению композитных материалов, которое не может быть удовлетворительно осуществлено с использованием обычных методов. KW - 3D Scanning KW - Water Pressure Processing KW - Clean Waterjet Cutting KW - Measurement of Manufacturing Accuracy Y1 - 2021 UR - http://www.ama.com.az/category/journal/ SN - 2076-0515 SN - 2789-8245 VL - 13 IS - 3 SP - 38 EP - 44 ER - TY - GEN A1 - Rasim, Bashirov A1 - Amirov, Fariz T1 - Выбор материала и геометрических параметров расточного резца для обработки покрытий на основе никеля T1 - Selecting material and geometrical parameters for a boring cutter used in machining the nickel-based coatings T2 - ИЗВЕСТИЯ ВЫСШИХ УЧЕБНЫХ ЗАВЕДЕНИЙ. МАШИНОСТРОЕНИЕ N2 - Разработка технологии механической обработки восстанавливаемых в ремонтном производстве деталей, включающая в себя выбор способа и режимов их обработки, режущего инструмента и др., является сложной задачей, решение которой определяет качество восстанавливаемых изделий. Качество механической обработки во многом зависит от обрабатываемости металла, под которой понимают способность материала подвергаться резанию. Рассмотрены особенности механической обработки втулок по- сле восстановления изношенной внутренней поверхности, состоящей из черного, чи- стового и тонкого растачивания, а также операции хонингования. При механической обработке восстанавливаемых втулок наибольшую трудность представляют операции чернового и чистового растачивания, так как после индукционного напекания с по- следующим раскатыванием твердость получаемых слоев находится в пределах HRC 48…55, что усложняет работу резцов при растачивании втулок. Для наплавки на де- тали, работающие в условиях изнашивания (коррозионного, эрозионного и термиче- ского), применяют порошок ПГ-СР2, имеющий систему легирования Ni–Cr–B–Si. Значительную волнистость и шероховатость поверхности, возникающую в результате наплавки, устраняют накатыванием. Одним из важных вопросов при обработке по- крытий, нанесенных центробежным индукционным напеканием с последующим рас- катыванием, является выбор материала и геометрических параметров режущего ин- струмента для чернового и чистового растачивания. При правильном выборе матери- ала и геометрических параметров расточного резца можно значительно уменьшить износ режущего инструмента, что позволит увеличить его стойкость и производи- тельность обработки, а следовательно, снизить себестоимость изготовления детали. Исследовано влияние технологических параметров на износ и геометрических пара- метров на стойкость режущего инструмента с целью оптимизации условий растачи- вания восстановленных цилиндров судовых двигателей. N2 - Design and development of a technology for machining the parts to be restored in the repair industry includes selection of their machining method and modes, cutting tools, etc., and is a complex task, which solution determines the restored product quality. Machining quality largely depends on the metal machinability, which is understood as the material ability to be cut. The paper considers features of a bush machining after restoration of the worn inner surface, this operation consists of black, clean and fine boring, as well as of honing. Opera- tions of black and clean boring are the most difficult in machining the restored bushes. This happens because hardness of the resulting layers is in the range of HRC 48…55 after induc- tion sintering with subsequent rolling, which complicates the cutters operation in bush bor- ing. The PG-SR2 powder having the Ni-Cr-B-Si alloying system is used in the built-up weld- ing of parts working under wear, corrosion, erosion and elevated temperature conditions. Rolling is eliminating significant waviness and surface roughness resulting from sintering. One of the important issues in machining the coatings applied by centrifugal induction sin- tering is selection of the cutting tool material for black and clean boring. KW - механическая обработка, центробежное индукционное напекание KW - machining cutting path KW - centrifugal induction sintering KW - cutting tool material KW - cutter radial wear KW - cutter geometrical parameters KW - cutting path KW - центробежное индукционное напекание KW - радиальный износ резца KW - геометрические парамет-ры резца KW - путь резания Y1 - 2023 U6 - https://doi.org/10.18698/0536-1044-2023-8-78-86 SN - 0536-1044 VL - 8(761) IS - 8 SP - 78 EP - 86 ER - TY - GEN A1 - Bashirov, Rasim A1 - Amirov, Fariz T1 - Методика определения теплового состояния втулки цилиндра при центрoбежном индукционном напекании T1 - Method for Determining the Thermal State of the Cylinder Sleeve During Centrifugal Induction Sintering T2 - ИЗВЕСТИЯ ВЫСШИХ УЧЕБНЫХ ЗАВЕДЕНИЙ. МАШИНОСТРОЕНИЕ N2 - Распределение температуры во втулке цилиндра судового двигателя при ее нагреве и охлаждении — один из важнейших факторов, под действием которых формируются структура и свойства покрытий в процессе восстановления цилиндра методом центро- бежного индукционного напекания. Проведены экспериментальные исследования, позволившие получить графики распределения температуры по диаметрам втулки ци- линдра судового двигателя при ее нагреве и охлаждении. Установлено, что на процесс напекания порошковых материалов существенно влияют теплофизические свойства втулки. Изменяя скорость нагрева, можно получать покрытия при различных значени- ях температуры и времени напекания. Выполнено моделирование распределения тем- пературы в стенке втулки цилиндра при центробежном индукционном напекании в за- висимости от времени напекания, а также с учетом геометрических параметров втулки, теплоотдачи, теплопроводности, материала втулки, температуры внешней среды и т. д. Получены выражения для определения распределения температуры в стенке втулки цилиндра при центробежном индукционном напекании. Задавая значения параметров центробежного индукционного напекания, по полученным формулам можно смодели- ровать и заранее получить распределение температуры в стенке втулки цилиндра. Для визуального отображения изменения температурного поля во втулке при центробеж- ном индукционном напекании выполнено моделирование в среде Autodesk Fusion 360. N2 - The temperature distribution in the ship engine cylinder sleeve during its heating and cooling is one of the most important factors affecting formation of the structure and properties of coatings in the process of cylinder recovery by the method of induction centrifugal sintering. The article discusses experimental studies, which allow presenting graphs of the temperature distribution over the diameters of the ship engine cylinder sleeve during its heating and cool- ing. The thermophysical properties of the sleeve were found to significantly affect the process of sintering powder materials. By varying the heating rate, it is possible to obtain coatings at different temperatures and sintering time. Modeling the temperature distribution in the wall of the cylinder sleeve during centrifugal induction sintering depending on the sintering time is of interest as well as taking into account the geometrical parameters of the sleeve, heat trans- fer, thermal conductivity, sleeve material, ambient temperature, etc. Expressions are obtained for determining the temperature distribution in the wall of the cylinder sleeve during induc- tion centrifugal sintering. Using the obtained formulas, it is possible to simulate and obtain in advance the temperature distribution in the wall of the cylinder sleeve by setting the values of the parameters of centrifugal induction sintering. Modeling in the Autodesk Fusion 360 the temperature distribution in the sleeve during induction heating was obtained as well as visual display of the change in the temperature field in the sleeve during induction heating. KW - центробежное индукционное напекание KW - induction centrifugal sintering KW - восстановление цилин-дров KW - индукционный нагрев KW - порошковые покрытия KW - порошковый слой KW - тепловая энергия KW - cylinder recovery KW - induction heating KW - powder coatings KW - powder layer KW - thermal energy Y1 - 2022 U6 - https://doi.org/10.18698/0536-1044-2022-8-33-41 SN - 0536-1044 VL - 8(749) IS - 8 SP - 33 EP - 41 ER - TY - GEN A1 - Seidlitz, Holger A1 - Simon, Sylvio A1 - Elze, Lars A1 - Schulze, Marcus T1 - Herstellung von strukturierten Leichtbaukomponenten Y1 - 2015 N1 - 15. Schwarzheider Kunststoffkolloquium, 22. September 2015 ER - TY - GEN ED - Simon, Sylvio T1 - 3. Ingenieurtag 2016 der Fakultät Maschinenbau, Elektro- und Energiesysteme - GUS und Osteuropatag - NESEFF-Netzwerktreffen 2016, Tagungsband N2 - Die GUS- und Osteuropatage der Fakultät Maschinenbau, Elektro- und Energiesysteme sind eingebunden in eine gesamte Veranstaltungswoche, deren zentrales Element der Triebwerkstag (10 Jahre UTC) ist. Mit dem Internationalen Tag in Senftenberg bestehend aus internationalem Brückenbauwettbewerb mit Liveschaltung zur SSOU nach Shanghai und den weiteren internationalen Vorträgen sowie dem Ingenieurtag mit Informationen über Forschungsprofessuren, Automatisierungstechnik und Fabrikplanung. Ein Treffen von Absolventen rundet diese Programmwoche ab. Die Fakultät Maschinenbau, Elektro- und Energiesysteme entstand 2016 im Zuge der Neustrukturierung der Fakultäten der BTU CS nach ihrer Neugründung im Jahre 2013. Sie ging aus den Vorgängerfakultäten Maschinenbau, Elektrotechnik und Wirtschaftsingenieurwesen am Campus Cottbus und der Fakultät für Ingenieurwissenschaften am Campus Senftenberg hervor. Hier sind jetzt die Kompetenzen des Maschinenbau und der Elektround Energietechnik vereint. Der Austausch mit Wissenschaftler aus anderen Ländern wird als Tradition an beiden Standorten gelebt. Neben dem Empfang von Wissenschaftlern und Studierenden gehört auch der Besuch in den jeweiligen Ländern dazu. Mit der Gründung des internationalen Netzwerkes neseff im Jahr 2015 in Baku entstand ein Netzwerk, das sich mit seinen Schwerpunkten Energieerzeugung und Energieeffizienz mit bedeutenden und zentralen Fragen der modernen Volkswirtschaften auf breitem Gebiet beschäftigt. Es hat seine Heimstatt im IURS e.V., einem An-Institut der BTU CS. Die Tatsache, dass weitere osteuropäische Universitäten dem Netzwerk beitreten werden, stärkt das Netzwerk und seine Akteure. Zwischen den GUS- und Osteuropatagen der Fakultät 3, die erstmalig stattfinden und dem bereits zum 3. Mal stattfindenden Ingenieurtag in Senftenberg, er folgt der Tradition der Wissenschaftstage der Hochschule Lausitz, ist ein vielseitiges Vortrags- und Besuchsprogramm vorbereitet, das jedoch genügend Zeit für Gespräche und Diskussionen bietet. Ich wünsche uns Allen erfolgreichen Tage an der BTU CS. KW - Ingenieurtag 2016 KW - GUS- und Osteuropatag KW - Neseff-Netzwerktreffen Y1 - 2016 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:co1-opus4-40523 SN - 978-3-940471-28-4 PB - Brandenburgische Techn. Univ. CY - Cottbus-Senftenberg ER - TY - GEN A1 - Salem, Shehab A1 - Fraňa, Karel A1 - Simon, Sylvio T1 - Experimental and Numerical Study of the AeroAcoustics of Flow over Structured Sheet Metals T2 - 2021 25th International Conference on Circuits, Systems, Communications and Computers (CSCC) N2 - This paper investigates experimentally and numerically the aero-acoustic noise generated by airflow around sheet metals with periodic hills of three different geometries named KMT, PWO and WAB used in automotive industry. Each sheet was tested experimentally in a wind tunnel at airflow of free-stream-velocity of 18 m/s and Reynold’s number based on the respective sheet thickness in the range of 1800-4200. The experiment was based on measuring the aero-dynamic sound generated by each sheet using a microphone. Moreover, it was based on measuring the velocity fluctuation after the sheets trailing edge by a Hot Wire Anemometer (HWA). Finally, an acoustic camera was used to locate the locations of sound sources in the flow. On the other hand, the numerical analysis used turbulence model as Large Eddy Simulation with Kinetic Energy Transport as a sub-grid model. Ffowcs-Williams & Hawkings model was used to predict the acoustic sources. Agreements were found between the trend of acoustic noise produced from experiment and numerical simulation over some ranges of frequency. The experiment has showed that the three sheets had comparable sound pressure level over the whole spectrum while the numerical results have showed that KMT sheet has achieved significant loudness at frequencies under 400 Hz while the WAB sheet has achieved significant quietness at frequencies below 400 Hz. The velocity contours obtained from the simulation showed that flow is laminar over some length before it changes to turbulent at a transition point. This behavior agrees with other data presented for long sheets subjected to flow of similar values of Reynolds Number. KW - strukturiertes Blech KW - Strömmungsakustik Y1 - 2021 SN - 978-1-6654-2749-4 U6 - https://doi.org/10.1109/CSCC53858.2021.00013 SP - 26 EP - 36 ET - 1. Auflage ER - TY - CHAP A1 - Simon, Sylvio A1 - Fraňa, Karel A1 - Egert, Josef A1 - Kořínek, Tomáš ED - Simon, Sylvio T1 - Untersuchungen an Wärmetauchern für Fußbodenheizungen T2 - 3. Ingenieurtag 2016 der Fakultät Maschinenbau, Elektro- und Energiesysteme - GUS und Osteuropatag - NESEFF-Netzwerktreffen 2016, Tagungsband N2 - Das Ziel der Untersuchung ist die Entwicklung eines neuen Konzeptes für Wärmetauscher sowie die experimentellen und numerischen Untersuchung an den wärmeübertragenden Flächen. Für die experimentelle Untersuchung wurde eine neue Messanlage gebaut und die Untersuchungsverfahren für die thermodynamischen Tests definiert. Die Strömung mit Wärmeübergang wurde mit der Hilfe der numerischen Simulation untersucht. Die Ergebnisse wurden mit den experimentellen Ergebnissen vergleichen und zeigten eine hohe Übereinstimmung. Außer den thermodynamischen Untersuchungen wurden auch Studien der Luftqualität durchgeführt. In diesem Fall geht es um eine numerische Studie zur CO2 Verteilung im Raum. Eine niedrige erforderliche Frischluftzufuhr führt oft zu einem niedrigen Energieverbrauch KW - strukturierte Bleche KW - Wärmetauscher KW - Strömung KW - Berechnung KW - Wärmeübertragung KW - Wandflächen KW - CO2 Verteilung Y1 - 2016 SN - 978-3-940471-28-4 SP - 115 EP - 119 PB - Cottbus-Senftenberg CY - Brandenburgische Techn. Univ. ER - TY - GEN A1 - Simon, Sylvio A1 - Shvetz, Vasily A1 - Palekhova, Ludmila A1 - Palekhov, Dmitry T1 - International Network Neseff - Networking for Energy supply and energy efficiency T1 - Internationales Netzwerk Neseff T2 - Bulletin of Prydneprovs'ka State Academy of Civil Engineering and Architecture KW - Netzwerk Energieeffizienz Y1 - 2016 SN - 2312-2676 IS - 3 SP - S. 6 ER - TY - GEN A1 - Shvetz, Vasily A1 - Palekhova, Ludmila A1 - Palekhov, Dmitry A1 - Simon, Sylvio T1 - Energy efficiency criteria as a focus for market-driven strategies of large companies in transition economies T1 - Критерии энергоэффективности как основа для разработки рыночных стратегий крупных компаний в странах с переходной экономикой T2 - Journal Scientific Bulletin of National Mining University N2 - The purpose of the presented research is to reveal the critical importance of energy efficiency indicators for large industrial companies from countries with economies in transition for increasing their competitiveness in local and global markets. KW - energy efficiency KW - global value chains KW - market strategies KW - sustainable development KW - transition economy Y1 - 2018 SN - 2071-2227 SN - 2223-2362 IS - 6 SP - 157 EP - 164 ER - TY - GEN ED - Simon, Sylvio T1 - International workshop "Energy supply and energy efficiency" N2 - Vom 21.-27.09.2015 fand mit Unterstützung des Auswärtigen Amtes an der Technischen Universität Aserbaidschan der internationale Workshop Energieversorgung - Energieeffizienz statt. Hierbei trafen sich Wissenschaftler, Mitarbeiter und Studierende aus 4 Ländern zusammen, um über aktuelle Fragestellungen und ihre Lösungen im Bereich Energieversorgung - Energieeffizienz zu diskutieren. KW - International workshop Y1 - 2015 SN - 3-9810211-8-5 PB - Brandenburgische Technische Universität CY - Cottbus ; Senftenberg ER - TY - BOOK A1 - Hönow, Gerhard A1 - Meißner, Thomas T1 - 機械設計實戰—從零件、裝配到創新設計 T1 - Konstruktionspraxis im Maschinenbau : vom Einzelteil zum Maschinendesign KW - Konstruktionslehre KW - Maschinenbau Y1 - 2023 SN - 978-7-111-72635-7 PB - China Machine Press CY - Peking ET - 5. Auflage ER - TY - GEN A1 - Bürger, Andreas A1 - Simon, Sylvio A1 - Hernschier, Stephan ED - Namazov, Subhan ED - Yusubov, Nizami ED - Simon, Sylvio T1 - Intelligent Sensor Technology for Rotating Parts in Machines and Plants T2 - Machine Building and Energy: New Concepts and Technologies (MBENCT) N2 - Rotating parts such as shafts, gear wheels, ball bearings or rollers are subject to wear that limits their life cycle. Damage causes loss of production and consequential damage to the entire pro- duction plant. Based on the application in a support roller, a system design is presented with which it is possible to record and wirelessly transmit relevant measured values in or on rotating machines without an additional voltage source. The system is largely maintenance-free and can be implemented with components that are currently freely available on the market. KW - sensors, rotating machinery, monitoring, energy harvesting, maintenance, data logging, rollers Y1 - 2024 UR - https://www.scientific.net/book/machine-building-and-energy-new-concepts-and-technologies-mbenct/978-3-0364-1034-0 SN - 978-3-0364-1034-0 SP - 209 EP - 216 PB - Trans Tech Publication Ltd. CY - Baech ET - 1.Auflage ER - TY - GEN A1 - Simon, Sylvio A1 - Yusubov, Nizami A1 - Amirli, Samir ED - Simon, Sylvio ED - Amirov, Fariz ED - Namazov, Subhan T1 - Formation of Geometric Parameters of the Surfaces of Cylindrical Parts during Waterjet Cutting T2 - Machine Building and Energy: New Concepts and Technologies (MBENCT) N2 - The article is devoted to the study of the technological process of water jet cutting of cylindrical parts on CNC machines. The results of experimental data on determining the accuracy of dimensional deviation, surface roughness, and taper of cylindrical parts depending on the circular milling of a water jet during water jet cutting are presented. Y1 - 2023 UR - https://www.scientific.net/book/machine-building-and-energy-new-concepts-and-technologies-mbenct/978-3-0364-1034-0 SN - 978-0364-0034-1 SP - 59 EP - 64 PB - Trans Tech Publication Ltd. CY - Baech ER - TY - GEN ED - Simon, Sylvio ED - Yusubov, Nizami ED - Namazov, Subhan T1 - Machine Building and Energy: New Concepts and Technologies (MBENCT) N2 - Selected peer-reviewed full text papers from the 2nd International Scientific-Practical Conference "Machine Building and Energy: New Concepts and Technologies" (MBENCT 2023) KW - machine building KW - technologies KW - machine tools KW - energy efficiency Y1 - 2023 SN - 978-0364-0034-1 U6 - https://doi.org/10.4028/b-Yw09VE PB - Trans Tech Publication Ltd. CY - Baech ET - 1. Auflage ER -