TY - CHAP A1 - Beirow, Bernd A1 - Kühhorn, Arnold A1 - Giersch, Thomas A1 - Nipkau, Jens T1 - Optimization-Aided Forced Response Analysis of a Mistuned Compressor Blisk T2 - ASME Turbo Expo 2014, Turbine Technical Conference and Exposition, Volume 7B: Structures and Dynamics, Düsseldorf, Germany, June 16–20, 2014, Paper GT2014-25915 N2 - The forced response of the first rotor of an E3E-type high pressure compressor blisk is analyzed with regard to varying mistuning, varying engine order excitations and the consideration of aeroelastic effects. For that purpose, SNM-based reduced order models are used in which the disk remains unchanged while the Young’s modulus of each blade is used to define experimentally adjusted as well as intentional mistuning patterns. The aerodynamic influence coefficient technique is employed to model aeroelastic interactions. Furthermore, based on optimization analyses and depending on the exciting EO and aerodynamic influences it is searched for the worst as well as the best mistuning distributions with respect to the maximum blade displacement. Genetic algorithms using blade stiffness variations as vector of design variables and the maximum blade displacement as objective function are applied. An allowed limit of the blades’ Young’s modulus standard deviation is formulated as secondary condition. In particular, the question is addressed if and how far the aeroelastic impact, mainly causing aerodynamic damping, combined with mistuning can even yield a reduction of the forced response compared to the ideally tuned blisk. It is shown that the strong dependence of the aerodynamic damping on the inter-blade phase angle is the main driver for a possible response attenuation considering the fundamental blade mode. The results of the optimization analyses are compared to the forced response due to real, experimentally determined frequency mistuning as well as intentional mistuning. Copyright © 2014 by Rolls-Royce Deutschland Ltd & Co KG Y1 - 2014 SN - 978-0-7918-4577-6 U6 - https://doi.org/10.1115/GT2014-25915 PB - ASME ER - TY - CHAP A1 - Giersch, Thomas A1 - Kühhorn, Arnold A1 - Figaschewsky, Felix T1 - Probabilistic Analysis of Low Engine Order Excitation Due to Geometric Perturbations of Upstream Nozzle Guide Vanes : ISABE-2015-20165 T2 - Conference Proceedings from the 22nd International Symposium on Air Breathing Engines, October 25-30, 2015, Phoenix, Arizona Y1 - 2015 UR - http://hdl.handle.net/2374.UC/745749 SP - 1 EP - 9 PB - ISABE ER - TY - CHAP A1 - Stelldinger, Marco A1 - Giersch, Thomas A1 - Figaschewsky, Felix A1 - Kühhorn, Arnold T1 - A Semi-Unstructured Turbomachinery Meshing Library With Focus on Modeling of Specific Geometrical Features T2 - ECCOMAS VII European Congress on Computational Methods in Applied Sciences and Engineering, Crete, Greece, June 5-10, 2016 N2 - Computational Fluid Dynamics is widely used for the analysis and the design of turbomachinery blade rows. A well established method is the application of semi-unstructured meshes, that uses a combination of structured meshes in the radial direction and unstructured meshes in the axial as well as the tangential direction. This takes advantage of the approximately two dimensional flow field through the blade rows, whereby a fine radial discretization, excepting the near wall region, is not necessary. Otherwise, it is possible to discretize particular regions, e.g. the leading and trailing edge regions, in the axial and tangential direction without generating unnecessary nodes in the far field. The meshing approach is based on the projection of a two dimensional unstructured mesh defined at a reference surface. Once, the two dimensional mesh is generated the projection is achieved by transfinite interpolation from the reference surface to further radial surfaces using a structured mesh. Due to the modeling of geometrical features, especially fillets, advanced methods for the generation of structured meshes and mesh smoothing algorithms are required. The paper presents two different approaches for the generation of an appropriate structured mesh. The first is based on the solution of elliptic partial differential equations. The second approach is based on the split of the domain into fourteen appropriately arranged blocks. Furthermore, two smoothing methods for two dimensional unstructured meshes, a constrained Laplace smoothing and an optimization based approach, are presented. Regarding a more realistic representation of the geometry, methods for the modeling of cavities, variable clearance sizes and fillets are presented. Finally, a comparison of the smoothing techniques applied to a rotor passage is presented and the influence of chosen geometrical features on the flow solution is evaluated. Y1 - 2016 UR - https://www.eccomas2016.org/proceedings/pdf/7554.pdf ER - TY - GEN A1 - Figaschewsky, Felix A1 - Kühhorn, Arnold A1 - Beirow, Bernd A1 - Giersch, Thomas A1 - Nipkau, Jens A1 - Meinl, Ferdinand T1 - Simplified Estimation of Aerodynamic Damping for Bladed Rotors, Part 2: Experimental Validation During operation T2 - ASME Turbo Expo 2016, Turbomachinery Technical Conference and Exposition, Volume 7B, Structures and Dynamics, Seoul, South Korea, June 13–17, 2016 N2 - Due to increasing requirements of future engine projects, much effort has been spent on the design of more efficient turbomachinery blades in the recent years. Besides aerodynamic efficiency constraints, these designs need to meet structural criteria ensuring that they are safe and robust with respect to High Cycle Fatigue (HCF). The estimation of the resonant vibration amplitude is done based on the aerodynamic force and the overall damping level. Since, for many applications the contribution of mechanical damping is often rather low compared to the aerodynamic counterpart, the determination of the aerodynamic damping is vital for the estimation of the forced vibration response. This second part is meant to contribute to a simplified computation of the aerodynamic damping during operation by making additional assumptions: The investigated mode family shall not suffer from flutter, has a high reduced frequency and the influence of adjacent blades is negligible. Under these circumstances a simplified approach can be introduced that allows for the computation of the mean value of the aerodynamic damping based on a steady state CFD solution of the regarded stage. It is well known, that the aerodynamic damping of a blade mode family depends on the inter blade phase angle (IBPA) and its direction of propagation, which is not covered by the simplified approach. For higher modes the difference between the minimum and maximum damping is often low and the mean value is a good approximation, whereas for fundamental modes there is often a significant difference. However, it is shown that considering a mistuned vibration response of the rotor, the expected value of the mistuned damping exhibits the mean value of IBPA-dependent aerodynamic damping. CFD simulations of an oscillating airfoil indicate a certain validity range of the simplified approach based on a modified reduced frequency and inlet Mach number, which allows to determine for which industrial applications the approach is most suitable. Finally, this range of validity is verified with experimentally determined overall damping values from strain gauge measurements during operation for 2 different industrial applications, an axial compressor stage of a jet engine and a radial turbine stage of a turbocharger. Copyright © 2016 by Rolls-Royce Deutschland Ltd & Co KG Y1 - 2016 SN - 978-0-7918-4984-2 U6 - https://doi.org/10.1115/GT2016-56458 N1 - Paper No. GT2016-56458 PB - ASME CY - New York, NY [u.a.] ER - TY - GEN A1 - Figaschewsky, Felix A1 - Beirow, Bernd A1 - Kühhorn, Arnold A1 - Nipkau, Jens A1 - Giersch, Thomas A1 - Powers, Bronwyn T1 - Design and Analysis of an Intentional Mistuning Experiment Reducing Flutter Susceptibility and Minimizing Forced Response of a Jet Engine Fan T2 - ASME Turbo Expo 2017, GT2017-64621, June 26-30, 2017, Charlotte, NC, USA, Volume 7B N2 - Recent demands for a reduction of specific fuel consumption of jet engines have been opposed by increasing propulsive efficiency with higher bypass ratios and increased engine sizes. At the same time the challenge for the engine development is to design safe and efficient fan blades of high aspect ratios. Since the fan is the very first rotor stage, it experiences significant distortions in the incoming flow depending on the operating conditions. Flow distortions do not only lead to a performance and stall margin loss but also to remarkable low engine order (LEO) excitation responsible for forced vibrations of fundamental modes. Additionally, fans of jet engines typically suffer from stall flutter, which can be additionally amplified by reflections of acoustic pressure waves at the intake. Stall flutter appears before approaching the stall line on the fan’s characteristic and limits its stable operating range. Despite the fact that this “flutter bite” usually affects only a very narrow speed range, it reduces the overall margin of safe operation significantly. With increasing aspect ratios of ultra-high bypass ratio jet engines the flutter susceptibility will probably increase further and emphasizes the importance of considering aeromechanical analyses early in the design phase of future fans. This paper aims at proving that intentional mistuning is able to remove the flutter bite of modern jet engine fans without raising issues due to heavily increased forced vibrations induced by LEO excitation. Whereas intentional mistuning is an established technology in mitigating flutter, it is also known to amplify the forced response. However, recent investigations considering aeroelastic coupling revealed that under specific circumstances mistuning can also reduce the forced response due to engine order excitation. In order to allow a direct comparison and to limit costs as well as effort at the same time, the intentional mistuning is introduced in a non-destructive way by applying heavy paint to the blades. Its impact on the blade’s natural frequencies is estimated via finite element models with an additional paint layer. In parallel, this procedure is experimentally verified with painted fan blades in the laboratory. A validated SNM (subset of nominal system modes) representation of the fan is used as a computational model to characterize its mistuned vibration behavior. Its validation is done by comparing mistuned mode shape envelopes and frequencies of an experimental modal analysis at rest with those obtained by the updated computational model. In order to find a mistuning pattern minimizing the forced response of mode 1 and 2 at the same time and satisfying stability and imbalance constraints, a multi-objective optimization has been carried out. Finally, the beneficial properties of the optimized mistuning pattern are verified in a rig test of the painted rotor. Copyright © 2017 by Rolls-Royce Deutschland Ltd & Co KG KW - Flutter (Aerodynamics) KW - Desin KW - Jet engines Y1 - 2017 SN - 978-0-7918-5093-0 U6 - https://doi.org/10.1115/GT2017-64621 PB - ASME CY - New York, NY ER - TY - GEN A1 - Krause, Christoph A1 - Stelldinger, Marco A1 - Hanschke, Benjamin A1 - Kühhorn, Arnold A1 - Giersch, Thomas T1 - Asynchronous Response Analysis of Non-Contact Vibration Measurements on Compressor Rotor Blades T2 - ASME Turbo Expo 2017, GT2017-63200, June 26-30, 2017, Charlotte, NC, USA, Volume 7B N2 - Although the research in non-intrusive techniques for the measurement of vibration have made major progress since the beginning in the 1960’s, they are still mainly used as additional tool to the common strain gauges. Therefore, there is still a great deal of interest in the improvement of such non-contact vibration measurement techniques, to replace the intrusive ones with alternative techniques. One possibility to monitor all blades at once is blade tip-timing. The probes for a blade tip-timing measurement system are mounted circumferentially in the engine casing to log the passing times of the rotor blades. These logged time data will be compared with theoretically calculated passing times. The deviation between measured and calculated passing times can be transformed to blade displacement values. In recent years, several methods to analyse the acquired vibration data have been developed and improved. They are directed to evaluate synchronous and asynchronous blade vibration events. This paper focuses on the identification of asynchronous vibrations on rotor blades using blade tip-timing. Taking the data from all probes into account gives an opportunity to determine the vibration of each single blade. Due to the usage of a research test rig, all measurement data could be acquired in simulated real case operation scenarios. Analysis data were evaluated with a developed post processing routine based on a Fourier transformation algorithm coupled with a least square fitting procedure. Since compressor surge represents one of the most critical non synchronous events during compressor operation, in this paper a special interest is paid to the analysis of compressor surges. Vibration frequencies revealed during surge investigation will be compared with simultaneously measured strain gauge data to ensure the reliability of blade tip-timing measurement and analysis. To explain the results in more detail, the possibility of a blade damaged triggered shift of the blade characteristic frequency is shown. The most promising result of the analysis is the close correlation between the identified vibration frequencies of compressor surge events and the afterwards determined frequency mistuning and crack distributions. Blade damage becomes visible through increasing deviation between characteristic frequencies of different blades as result of multiple surge events. In addition, with the comparison of mean frequency records over each single surge among each other it is possible to restrict the blade damage time. Subsequently, the possibility to develop a process routine to predict blade damage during compressor test series could arise. KW - Compressors KW - Rotors KW - Blades KW - Vibration measurement Y1 - 2017 SN - 978-0-7918-5093-0 U6 - https://doi.org/10.1115/GT2017-63200 PB - ASME CY - New York, NY ER - TY - CHAP A1 - Figaschewsky, Felix A1 - Kühhorn, Arnold A1 - Beirow, Bernd A1 - Giersch, Thomas A1 - Schrape, Sven T1 - Analysis of Mistuned Forced Response in an Axial High Pressure Compressor Rig With Focus on Tyler-Sofrin Modes T2 - ISABE 2017, ISABE-2017-22614, Manchester, September 3.-8., 2017 Y1 - 2017 PB - ISABE ER - TY - CHAP A1 - Beirow, Bernd A1 - Kühhorn, Arnold A1 - Figaschewsky, Felix A1 - Hönisch, Peter A1 - Giersch, Thomas A1 - Schrape, Sven T1 - Model Update and Validation of a Mistuned High Pressure Compressor Blisk T2 - Proceedings of ISABE 2017, ISABE-2017-22568, Manchester, September 3.-8., 2017 Y1 - 2017 UR - https://isabe2017.org/ PB - ISABE ER - TY - CHAP A1 - Figaschewsky, Felix A1 - Kühhorn, Arnold A1 - Giersch, Thomas T1 - A Finite Element Based Least Square Fit for the Assessment of Integral and Non-Integral Vibrations With Blade Tip Timing T2 - Proceedings of ISROMAC 2017, Maui, Hawaii, December 16-21, 2017 N2 - This paper aims at improving the robustness and accuracy of the least square fit technique utilized in blade tip timing (BTT) measurements of blade vibrations by proposing two modifications. The first proposal is to replace the lines of the original least square problem by differences of consecutive lines. Thereby, the static deflection as well as the circumferential blade positioning error cancels out and the robustness is improved by removing these uncertainties inherently. The second proposal is to replace the fit of piecewise constant vibration amplitudes within the chosen block length by a linear or cubic spline in the frequency (integral) or time (non-integral) regime. This does not only suppress overshoots due to distorted acceleration or deceleration manoeuvres but also allows for a ”coarser analysis grid” (i.e. larger block length) without loosing amplitude accuracy. Thereby it smooths out random errors more efficiently and increases the orthogonality of the relevant EO or vibration frequency to unwanted signal components. KW - Blade Tip Timing KW - Non-Intrusive Measurements KW - Blade Vibration Y1 - 2017 UR - http://isromac-isimet.univ-lille1.fr/index.php?rubrique=abstract17_&num=2 ER - TY - CHAP A1 - Hanschke, Benjamin A1 - Kühhorn, Arnold A1 - Schrape, Sven A1 - Giersch, Thomas T1 - Consequences of Borescope Blending Repairs on Modern HPC Blisk Aeroelasticity T2 - Proceedings of ISROMAC 2017, Maui, Hawaii, December 16-21, 2017 N2 - Objective of this paper is to analyse the consequences of borescope blending repairs on the aeroelastic behaviour of a modern HPC blisk. To investigate the blending consequences in terms of aerodynamic damping and forcing changes, an exemplary blending of a rotor blade is modelled. Steady state flow parameters like total pressure ratio, polytropic efficiency and the loss coefficient are compared. Furthermore, aerodynamic damping is computed utilising the AIC approach for both geometries. Results are confirmed by SPF simulations for specific nodal diameters of interest. Finally, an unidirectional forced response analysis for the nominal and the blended rotor is conducted to determine the aerodynamic force exciting the blade motion. Fourier transformation of the forcing signal yields to the frequency content as well as the forcing amplitudes. As a result of the present analysis, the amplification of expected blade vibration amplitude is computed. KW - Aeroelasticity KW - Compressor Blisk KW - Blending Repair KW - Forced Response KW - Arodynamic Damping Y1 - 2017 UR - http://isromac-isimet.univ-lille1.fr/index.php?rubrique=abstract17_&num=2 ER -