TY - CHAP A1 - Beirow, Bernd A1 - Kühhorn, Arnold A1 - Giersch, Thomas A1 - Nipkau, Jens T1 - Forced Response Analysis of a Mistuned Compressor Blisk T2 - ASME Turbo Expo 2013: Turbine Technical Conference and Exposition, San Antonio, Texas, USA, June 3–7, 2013, Vol. 7B, Structures and Dynamics, Paper GT2013-94142 N2 - The forced response of an E3E-type HPC-blisk front rotor is analyzed with regard to varying mistuning and the consideration of the fluid-structure interaction (FSI). For that purpose, a reduced order model is used in which the disk remains unchanged and mechanical properties of the blades namely stiffness and damping are adjusted to measured as well as intentional blade frequency mistuning distributions. The aerodynamic influence coefficient technique is employed to model the aeroelastics. Depending on the blade mode, the exciting engine order and aerodynamic influences it is sought for the worst mistuning distributions with respect to the maximum blade displacement based on optimization analyses. Genetic algorithms using blade alone frequencies as design variables are applied. The validity of the Whitehead-limit is assessed in this context. In particular, the question is addressed if and how far aeroelastic effects, mainly caused by aerodynamic damping, combined with mistuning can even cause a reduction of the forced response compared to the ideally tuned blisk. It is shown that the strong dependence of the aerodynamic damping on the inter-blade phase angle is the main driver for a possible response attenuation considering the fundamental as well as a higher blade mode. Furthermore, the differences to the blisk vibration response without a consideration of the flow and an increase of the disk’s stiffness are discussed. Closing, the influence of pure damping mistuning is analyzed again using optimization. KW - Compressors KW - Blades KW - Blisks KW - Mistuning Y1 - 2013 UR - http://proceedings.asmedigitalcollection.asme.org/proceeding.aspx?articleid=1776795 SN - 978-0-7918-5527-0 U6 - https://doi.org/10.1115/GT2013-94142 PB - ASME CY - New York ER - TY - CHAP A1 - Giersch, Thomas A1 - Figaschewsky, Felix A1 - Hönisch, Peter A1 - Kühhorn, Arnold A1 - Schrape, Sven T1 - Numerical Analysis and Validation of the Rotor Blade Vibration Response Induced by High Pressure Compressor Deep Surge T2 - ASME Turbo Expo 2014: Turbine Technical Conference and Exposition, Volume 7B: Structures and Dynamics Düsseldorf, Germany, June 16–20, 2014, Paper GT2014-26295 N2 - The following paper presents a numerical analysis of a deep surge cycle of a 4.5 stage research compressor. The resulting unsteady loads are used to determine the response of two particular rotor blade rows that are then compared to strain gauge data from measurements. Within a deep surge cycle the compressor experiences a rapid change of the flow field from forward to reversed flow. This rapid breakdown is linked to a new mean blade load. Hence, the rapid change in blade loads are able to excite fundamental blade modes similar to an impulse load. The resulting vibration magnitudes might reach critical levels. This paper demonstrates two different approaches to evaluate the unsteady flow during a surge cycle. The first uses a three dimensional, time accurate finite volume solver for viscid compressible flows to calculate the transient surge cycle of the compressor. The compressor itself is represented by a multi-blade-row sector model. The second approach makes use of the same solver and compressor domain to determine steady state characteristics of the HPC in forward, stalled and reversed flow. Based on these characteristics an one dimensional finite volume solver for inviscid compressible flows was developed to determine the transient compressor behavior. The one dimensional solver represents the compressor by source terms that are linked to the previously determined steady state characteristics. Copyright © 2014 by Rolls-Royce Deutschland Ltd & Co KG KW - Compressors KW - High pressure (Physics) KW - Numerical analysis Y1 - 2014 SN - 978-0-7918-4577-6 U6 - https://doi.org/10.1115/GT2014-26295 PB - ASME CY - New York, NY ER - TY - GEN A1 - Krause, Christoph A1 - Stelldinger, Marco A1 - Hanschke, Benjamin A1 - Kühhorn, Arnold A1 - Giersch, Thomas T1 - Asynchronous Response Analysis of Non-Contact Vibration Measurements on Compressor Rotor Blades T2 - ASME Turbo Expo 2017, GT2017-63200, June 26-30, 2017, Charlotte, NC, USA, Volume 7B N2 - Although the research in non-intrusive techniques for the measurement of vibration have made major progress since the beginning in the 1960’s, they are still mainly used as additional tool to the common strain gauges. Therefore, there is still a great deal of interest in the improvement of such non-contact vibration measurement techniques, to replace the intrusive ones with alternative techniques. One possibility to monitor all blades at once is blade tip-timing. The probes for a blade tip-timing measurement system are mounted circumferentially in the engine casing to log the passing times of the rotor blades. These logged time data will be compared with theoretically calculated passing times. The deviation between measured and calculated passing times can be transformed to blade displacement values. In recent years, several methods to analyse the acquired vibration data have been developed and improved. They are directed to evaluate synchronous and asynchronous blade vibration events. This paper focuses on the identification of asynchronous vibrations on rotor blades using blade tip-timing. Taking the data from all probes into account gives an opportunity to determine the vibration of each single blade. Due to the usage of a research test rig, all measurement data could be acquired in simulated real case operation scenarios. Analysis data were evaluated with a developed post processing routine based on a Fourier transformation algorithm coupled with a least square fitting procedure. Since compressor surge represents one of the most critical non synchronous events during compressor operation, in this paper a special interest is paid to the analysis of compressor surges. Vibration frequencies revealed during surge investigation will be compared with simultaneously measured strain gauge data to ensure the reliability of blade tip-timing measurement and analysis. To explain the results in more detail, the possibility of a blade damaged triggered shift of the blade characteristic frequency is shown. The most promising result of the analysis is the close correlation between the identified vibration frequencies of compressor surge events and the afterwards determined frequency mistuning and crack distributions. Blade damage becomes visible through increasing deviation between characteristic frequencies of different blades as result of multiple surge events. In addition, with the comparison of mean frequency records over each single surge among each other it is possible to restrict the blade damage time. Subsequently, the possibility to develop a process routine to predict blade damage during compressor test series could arise. KW - Compressors KW - Rotors KW - Blades KW - Vibration measurement Y1 - 2017 SN - 978-0-7918-5093-0 U6 - https://doi.org/10.1115/GT2017-63200 PB - ASME CY - New York, NY ER - TY - GEN A1 - Figaschewsky, Felix A1 - Kühhorn, Arnold A1 - Beirow, Bernd A1 - Giersch, Thomas A1 - Schrape, Sven A1 - Nipkau, Jens T1 - An inverse approach to identify tuned aerodynamic damping, system frequencies and mistuning – Part 3: Application to engine data T2 - ASME Turbo Expo 2019: Turbomachinery Technical Conference and Exposition, June 17–21, 2019, Phoenix, Arizona, USA N2 - A novel approach for the identification of tuned aerodynamic damping, system frequencies, forcing and mistuning has been introduced in the first part of this paper. It is based on the forced response equations of motion for a blade dominated mode family. A least squares formulation allows to identify the system’s parameters directly from measured frequency response functions (FRFs) of all blades recorded during a sweep through a resonance. The second part has dealt with its modification and application to experimental modal analyses of blisks at rest. This 3rd part aims at presenting the application of the approach to blade tip timing (BTT) data acquired in rig tests. Therefore, blisk rotors of two different engines are studied: a single stage fan rig and a 4.5 stage high pressure compressor (HPC) rig. The rig test campaign of the fan blisk included also an intentional mistuning experiment that allows to study the performance of the identification approach for a similar rotor with two different mistuning levels. It is demonstrated that the approach can identify aerodynamic damping curves, system frequencies, mistuning pattern and forced travelling wave modes (TWMs) from state of the art BTT data monitored during rig or engine tests. All derived mistuning patterns could be verified with reference measurements at standstill. The derived aerodynamic damping curves and system frequencies show a reasonable agreement with simulations. For the HPC case a multitude of excited TWMs could be identified which also lines up with previous simulations. KW - Damping KW - Engines KW - Blades KW - Engineering simulation KW - Rotors KW - Compressors KW - Modal analysis Y1 - 2019 UR - https://asmedigitalcollection.asme.org/GT/proceedings-abstract/GT2019/58684/V07AT36A014/1067111 SN - 978-0-7918-5868-4 U6 - https://doi.org/10.1115/GT2019-91337 ER -