TY - CHAP A1 - Stelldinger, Marco A1 - Giersch, Thomas A1 - Figaschewsky, Felix A1 - Kühhorn, Arnold T1 - A Semi-Unstructured Turbomachinery Meshing Library With Focus on Modeling of Specific Geometrical Features T2 - ECCOMAS VII European Congress on Computational Methods in Applied Sciences and Engineering, Crete, Greece, June 5-10, 2016 N2 - Computational Fluid Dynamics is widely used for the analysis and the design of turbomachinery blade rows. A well established method is the application of semi-unstructured meshes, that uses a combination of structured meshes in the radial direction and unstructured meshes in the axial as well as the tangential direction. This takes advantage of the approximately two dimensional flow field through the blade rows, whereby a fine radial discretization, excepting the near wall region, is not necessary. Otherwise, it is possible to discretize particular regions, e.g. the leading and trailing edge regions, in the axial and tangential direction without generating unnecessary nodes in the far field. The meshing approach is based on the projection of a two dimensional unstructured mesh defined at a reference surface. Once, the two dimensional mesh is generated the projection is achieved by transfinite interpolation from the reference surface to further radial surfaces using a structured mesh. Due to the modeling of geometrical features, especially fillets, advanced methods for the generation of structured meshes and mesh smoothing algorithms are required. The paper presents two different approaches for the generation of an appropriate structured mesh. The first is based on the solution of elliptic partial differential equations. The second approach is based on the split of the domain into fourteen appropriately arranged blocks. Furthermore, two smoothing methods for two dimensional unstructured meshes, a constrained Laplace smoothing and an optimization based approach, are presented. Regarding a more realistic representation of the geometry, methods for the modeling of cavities, variable clearance sizes and fillets are presented. Finally, a comparison of the smoothing techniques applied to a rotor passage is presented and the influence of chosen geometrical features on the flow solution is evaluated. Y1 - 2016 UR - https://www.eccomas2016.org/proceedings/pdf/7554.pdf ER - TY - GEN A1 - Krause, Christoph A1 - Stelldinger, Marco A1 - Hanschke, Benjamin A1 - Kühhorn, Arnold A1 - Giersch, Thomas T1 - Asynchronous Response Analysis of Non-Contact Vibration Measurements on Compressor Rotor Blades T2 - ASME Turbo Expo 2017, GT2017-63200, June 26-30, 2017, Charlotte, NC, USA, Volume 7B N2 - Although the research in non-intrusive techniques for the measurement of vibration have made major progress since the beginning in the 1960’s, they are still mainly used as additional tool to the common strain gauges. Therefore, there is still a great deal of interest in the improvement of such non-contact vibration measurement techniques, to replace the intrusive ones with alternative techniques. One possibility to monitor all blades at once is blade tip-timing. The probes for a blade tip-timing measurement system are mounted circumferentially in the engine casing to log the passing times of the rotor blades. These logged time data will be compared with theoretically calculated passing times. The deviation between measured and calculated passing times can be transformed to blade displacement values. In recent years, several methods to analyse the acquired vibration data have been developed and improved. They are directed to evaluate synchronous and asynchronous blade vibration events. This paper focuses on the identification of asynchronous vibrations on rotor blades using blade tip-timing. Taking the data from all probes into account gives an opportunity to determine the vibration of each single blade. Due to the usage of a research test rig, all measurement data could be acquired in simulated real case operation scenarios. Analysis data were evaluated with a developed post processing routine based on a Fourier transformation algorithm coupled with a least square fitting procedure. Since compressor surge represents one of the most critical non synchronous events during compressor operation, in this paper a special interest is paid to the analysis of compressor surges. Vibration frequencies revealed during surge investigation will be compared with simultaneously measured strain gauge data to ensure the reliability of blade tip-timing measurement and analysis. To explain the results in more detail, the possibility of a blade damaged triggered shift of the blade characteristic frequency is shown. The most promising result of the analysis is the close correlation between the identified vibration frequencies of compressor surge events and the afterwards determined frequency mistuning and crack distributions. Blade damage becomes visible through increasing deviation between characteristic frequencies of different blades as result of multiple surge events. In addition, with the comparison of mean frequency records over each single surge among each other it is possible to restrict the blade damage time. Subsequently, the possibility to develop a process routine to predict blade damage during compressor test series could arise. KW - Compressors KW - Rotors KW - Blades KW - Vibration measurement Y1 - 2017 SN - 978-0-7918-5093-0 U6 - https://doi.org/10.1115/GT2017-63200 PB - ASME CY - New York, NY ER -