TY - GEN A1 - Shrestha, Krishna Prasad A1 - Giri, Binod Raj A1 - Adil, Mohammad A1 - Seidel, Lars A1 - Zeuch, Thomas A1 - Farooq, Aamir A1 - Mauß, Fabian T1 - Detailed Chemical Kinetic Study of Acetaldehyde Oxidation and Its Interaction with NOx T2 - Energy & fuels N2 - This work entails a detailed modeling and experimental study for the oxidation kinetics of acetaldehyde (CH3CHO) and its interaction with NOx. The ignition behavior of CH3CHO/O2/Ar has been investigated in a shock tube over the temperature range of 1149 to 1542 K, with equivalence ratios of 0.5 and 1.0 and pressures near 1.2 bar. Absorbance−time profiles of acetaldehyde were recorded using a mid-IR laser during the autoignition measurements. A comprehensive kinetic model has been developed to quantitatively predict the oxidation of acetaldehyde and its interaction with NOx. The kinetic model has been validated using experimental data of this work and available literature data from shock tube, plug flow, and jet-stirred reactors, freely propagating, and burner-stabilized premixed flames. For better accuracy of the kinetic model, the thermochemistry of 14 important species in the acetaldehyde submechanism was calculated using ab initio methods. The heat of formation of these species was computed using atomization and isodesmic reaction schemes. For the first time, this modeling study examines the effect of NO on acetaldehyde oxidation behavior over a wide range of experimental conditions. In most cases, the proposed kinetic model captures the experimental trends remarkably well. Interestingly, the doping of NO in CH3CHO did not perturb the NTC behavior of CH3CHO in contrast to other fuels, such as n-heptane and dimethyl ether. However, for flow reactor conditions at 1 atm, doping with 504 ppm of NO was found to promote the reactivity of acetaldehyde by lowering the onset temperature for CH3CHO oxidation by ∼140 K. The hydroxyl radical is the main cause of this shift, which originates from the NO + HO2 = OH + NO2 reaction. Further evolution of hydroxyl radicals occurs via the “NO−NO2” looping mechanism and expedites the reactivity of the system. This experimental and modeling work sheds new light on acetaldehyde oxidation behavior and its interaction with NOx under combustion-relevant conditions. KW - NOx KW - Kinetic modeling KW - Acetaldehyde KW - Ignition delay time Y1 - 2021 UR - https://pubs.acs.org/doi/10.1021/acs.energyfuels.1c01948?ref=pdf U6 - https://doi.org/10.1021/acs.energyfuels.1c01948 SN - 1520-5029 SN - 0887-0624 VL - 35 IS - 18 SP - 14963 EP - 14983 ER - TY - GEN A1 - Issayev, Gani A1 - Giri, Binod Raj A1 - Elbaz, Ayman M. A1 - Shrestha, Krishna Prasad A1 - Mauß, Fabian A1 - Roberts, William L. A1 - Farooq, Aamir T1 - Ignition delay time and laminar flame speed measurements of ammonia blended with dimethyl ether: A promising low carbon fuel blend T2 - Renewable Energy N2 - Ammonia (NH3) has recently received much attention as a promising future fuel for mobility and power generation. The use of ammonia as a fueling vector can help curb global warming by cutting CO2 emissions because it is a carbon-free fuel and a hydrogen carrier with a high percentage of hydrogen atoms per unit volume. Liquid ammonia contains a higher volumetric density of hydrogen than liquid hydrogen. The low reactivity of ammonia, however, hinders its direct usage as a combustible fuel. One feasible way to boost the reactivity of ammonia is to target a dual-fuel system comprising of ammonia and a suitable combustion promoter. In this work, combustion properties of ammonia were investigated by blending it with various proportions of dimethyl ether (DME) using a rapid compression machine (RCM) and a constant volume spherical reactor (CVSR) over a wide range of experimental conditions. DME is a highly reactive fuel that may be produced in a sustainable carbon cycle with a net zero-carbon emission. Ignition delay times (IDTs) of NH3/DME blends were measured over a temperature (T) range of 649e950 K, pressures (P) of 20 and 40 bar, equivalence ratios (F) of 0.5 and 1 for a range of DME mole fractions (cDME) of 0.05e0.5 in the blends. In addition, the laminar burning velocities of NH3/DME blends were measured at P ¼ 1, 3 and 5 bar, F ¼ 0.8e1.3 and T ¼ 300 K for cDME ranging from 0.18 to 0.47. Our results suggest that DME is a good ignition promoter, resulting in a significant shortening of IDTs and an increase of flame speeds of NH3. A detailed chemical model has been developed and validated against the experimental data. Overall, our kinetic model offered reasonable predictive capabilities capturing the experimental trends over a wide range of conditions. In the worst-case scenario, our model underpredicted IDTs by a factor of ~2.5 while overpredicting laminar flame speed by ~20%. KW - DME KW - Lamianr flame speed KW - Ignition delay time KW - Kinetic modeling KW - Ammonia Y1 - 2022 UR - https://www.sciencedirect.com/science/article/pii/S0960148121014440?via%3Dihub#! U6 - https://doi.org/10.1016/j.renene.2021.09.117 SN - 1879-0682 VL - 181 SP - 1353 EP - 1370 ER - TY - GEN A1 - Shrestha, Krishna Prasad A1 - Giri, Binod Raj A1 - Seidel, Lars A1 - Farooq, Aamir A1 - Mauß, Fabian T1 - A Kinetic Modeling Study for the Effect of NOx on Oxymethylene ethers (OMEn, n = 0 and 1) oxidation T2 - 10th European Combustion Meeting, Neapel N2 - We present a detailed kinetic model for the oxidation of dimethyl ether (OME0) and dimethoxymethane (OME1) in presence of NOx. We further explored the effect of NOx chemistry on the oxidation kinetics of the two OMEs. Our kinetic model is validated against the recent flow reactor data from Zhang et al. (Combust. Flame. 224 (2021) 94– 107). The results indicated that NO doping severely alters the oxidation kinetics of both fuels. The onset temperature for total fuel consumption is significantly shifted to lower temperatures for both fuels, which is in line with the experimental observation. We found that the addition of NO significantly inhibited the NTC behaviour of dimethyl ether. This inhibiting effect appears to stem from the competition between CH3OCH2O2 radical consumption by NO directly and the isomerization/dissociation reactions of CH3OCH2O2. Unlike dimethyl ether, dimethoxymethane does not exhibit a strong NTC behavior, and NO addition completely inhibited its weak NTC behavior. KW - DME KW - DMM KW - Oxymethylene ethers KW - NOx KW - Kinetic Modeling Y1 - 2021 UR - https://www.researchgate.net/publication/353620538_A_Kinetic_Modeling_Study_for_the_Effect_of_NOx_on_Oxymethylene_ethers_OMEn_n_0_and_1_oxidation CY - Neapel ER - TY - GEN A1 - Shrestha, Krishna Prasad A1 - Giri, Binod Raj A1 - Elbaz, Ayman M. A1 - Issayev, Gani A1 - Roberts, William L. A1 - Seidel, Lars A1 - Mauß, Fabian A1 - Farooq, Aamir T1 - A detailed chemical insights into the kinetics of diethyl ether enhancing ammonia combustion and the importance of NOx recycling mechanism T2 - Fuel Communications N2 - In this work, we investigated the combustion characteristics of ammonia (NH3) by blending it with various proportions of diethyl ether (DEE). We measured laminar flame speed of various NH3/DEE blends (DEE, 10–40% by mole) using a constant volume spherical vessel at Ti = 298 K and Pi = 3 and 5 bar and Φ = 0.8–1.3. We developed a detailed kinetic model to describe the trends of the current and previously published experimental data. For the robustness of the model, we first developed a comprehensive diethyl ether kinetic mechanism to accurately characterize neat DEE oxidation behavior. We validated the kinetic model using a large pool of experimental data comprising shock tube, rapid compression machine, jet-stirred and flow reactors, freely propagating, and burner-stabilized premixed flames. The developed kinetic model performs remarkably in capturing the combustion behavior of pure DEE and NH3. Importantly, our model captures the experimental data of laminar flame speed and ignition delay times of various NH3/DEE blends over a wide range of conditions. We found that DEE is a promising candidate to promote the combustion characteristics of NH3. A small portion of DEE (10%) enhances the laminar flame speed of NH3 by a factor of 2 at Pi = 1 bar, Ti = 298 K, and Φ = 1.0. A further doubling of the DEE mole fraction to 20% did not enhance the laminar flame speed of NH3 with the same propensity. At low temperatures, adding 5% DEE in NH3 blend has significantly expedited the system reactivity by lowering the autoignition temperature. A further 5% increment of DEE (i.e., 10% DEE in NH3) lowers the autoignition temperature by ∼120 K to achieve the same ignition delay time. The “NOsingle bondNO2” looping mechanism predominantly drives such reactivity accelerating effect. Here, the reactions, NO + HO2 = NO2 + OH and NO2 + H = NO + OH, appear to enhance the reactive radical pool by generating OH radicals. We observed that the HNO path is favored more with increasing DEE content which eventually liberates NO. Other key reactions in “NOsingle bondNO2” looping mechanism are: CH3 + NO2 = CH3O + NO, CH3O2 + NO = CH3O + NO2, C2H5 + NO2 = C2H5O + NO, C2H5O2 + NO = C2H5O + NO2. In addition, CH3 + NH2(+M) = CH3NH2(+M) reaction is also one of the important cross-reactions which leads to the formation of HCN. Therefore, cross-reactions between the nitrogen and carbon family are crucial in accurately predicting autoignition timing. This work provides a detailed chemical insight into the NH3 and DEE interaction, which could be applied to other fuel blends of NH3. The kinetic model is also validated for several C1single bondC3 fuels including their interaction with NOx. KW - DEE KW - Ammonia KW - Kinetic Model KW - Laminar flame speed KW - Ignition delay time Y1 - 2022 U6 - https://doi.org/10.1016/j.jfueco.2022.100051 SN - 2666-0520 VL - 10 ER - TY - GEN A1 - Fritsche, Chris A1 - Eckart, Sven A1 - Shrestha, Krishna Prasad A1 - Mauß, Fabian A1 - Krause, Hartmut T1 - Methane flames with a substitution of 50 to 100 percent hydrogen: Experimental and numerical investigation of the temperature and pressure dependence of the laminar burning velocities T2 - 10th European Combustion Meeting, Proceedings of the European Combustion Meeting N2 - This work reports the laminar burning velocities for CH4/H2 blends in mixtures with air utilizing the constant volume chamber at temperatures from 300 to 423 K, pressures from 2 to 10 bar and equivalence ratios from 0.7 to 2.4. A detailed chemical kinetic model based on our previous work is used to reproduce the experimental data. The chemical kinetic model can reproduce the experimental data better at lean conditions compared to rich conditions. It is observed that with an increase in H2 fraction in fuel blend, laminar burning velocities increase. Model reveals that with increasing H2 fraction in the fuel blend, formation of key radicals H, OH and O are promoted leading to higher laminar burning velocities. The most sensitive reactions are O2+H=OH+O, CO+OH=CO2+H, CH4+H=CH3+H2 and CH4+OH=CH3+H2O. It is found that as initial mixture temperature increases, the laminar burning velocity increases and shows a linear trend whereas this trend is reversed as the initial pressure increases. KW - Methane KW - Hydrogen KW - Kinetic Model KW - Laminar burning velocity KW - Constant Volume chamber Y1 - 2021 UR - https://www.researchgate.net/publication/358415279_Methane_flames_with_a_substitution_of_50_to_100_percent_hydrogen_Experimental_and_numerical_investigation_of_the_temperature_and_pressure_dependence_of_the_laminar_burning_velocities ER - TY - GEN A1 - Fritsche, Chris A1 - Shrestha, Krishna Prasad A1 - Eckart, Sven A1 - Mauß, Fabian A1 - Krause, Hartmut T1 - Temperature and pressure dependency of the burning velocity in laminar premixed methanol and polyoxymethylene dimethyl ether (OME1, OME2, and OME3) flames T2 - 10th European Combustion Meeting, Proceedings of the European Combustion Meeting N2 - This work reports the laminar burning velocities (LBV) for the liquid fuels methanol, and polyoxymethylene dimethyl ethers (OMEn, n = 1-3) in mixtures with air utilizing the heat flux burner and constant volume chamber at temperature 393 to 443 K, pressure 1 to 10 bar, and equivalence ratio 0.6 to 1.9. Laminar burning velocities for OME2 and OME3 higher than 1 bar are reported for the first time. A detailed chemical kinetic model for OME2 and OME3 was developed based on our previous work utilizing experimental data from this work. Overall, model predictions are in good agreement with the experimental data. It is previously shown that with increases in unburned gas temperature laminar burning velocity increases and shows a linear trend with respect to temperature. Further, laminar burning velocity decreases with an increase of initial pressure. The dependence of burning velocity is not linear for all the fuels investigated. For comparable temperature and pressure conditions, it was found that with an additional CH2O group the laminar burning velocities increase marginally and there is no shift of maximum laminar burning velocity with respect to equivalence ratio. KW - Oxymethylene ethers KW - Lamianr burning velocity KW - Kinetic Modeling KW - heat flux burne KW - constant volume chamber Y1 - 2021 UR - https://www.researchgate.net/publication/358415681_Temperature_and_pressure_dependency_of_the_burning_velocity_in_laminar_premixed_methanol_and_polyoxymethylene_dimethyl_ether_OME1_OME2_and_OME3_flames ER - TY - GEN A1 - Shrestha, Krishna Prasad A1 - Seidel, Lars A1 - Zeuch, Thomas A1 - Mauß, Fabian T1 - Modeling of NOx Formation and Consumption during Oxidation of Small Alcohols T2 - 9th European Combustion Meeting, Proceedings of the European Combustion Meeting N2 - This work presents a newly developed kinetic mechanism extending our recent work (Shrestha et al. [1]) for the oxidation of methanol and ethanol and their fuel interaction with NO x chemistry in jet-stirred reactors, flow reactors, and burner-stabilized premixed flames. The work mainly focuses on fuel interaction with nitrogen chemistry and NO formation in laminar premixed flames. It is found that for methanol oxidation in jet-stirred reactor doping of the fuel blends with NO increase the reactivity of the system by increasing the net production of OH radicals. The increased amount of OH is formed via NO/NO 2 interconversion reaction channels NO+HO 2 ⇋NO 2 +OH, NO 2 +H⇋NO+OH, NO 2 +HO 2 ⇋HONO+O 2, followed by the thermal decomposition of HONO producing NO and OH. In burner-stabilized premixed flames studied here for methanol/air and ethanol/air, NO is mainly formed via the NCN route (CH+N 2 ⇋NCN+H) and minor contribution comes from the NNH route (NNN⇋N 2 +H). Y1 - 2019 UR - https://hal.archives-ouvertes.fr/hal-02334906 ER - TY - GEN A1 - Rakhi, Rakhi A1 - Shrestha, Krishna Prasad A1 - Günther, Vivien A1 - Mauß, Fabian T1 - Thermodynamic analysis to develop a detailed surface reaction mechanism T2 - Fuel Science - From Production to Propulsion, Aachen, Germany, May 2022 N2 - The reduction of greenhouse gasses such as CO2 and CH4 is becoming necessary due to global environmental problems. The reforming of light hydrocarbons is a particularly efficient process for producing synthesis gas, H2 and CO, from greenhouse gasses [1]. The steam reforming of methane is the most important method to produce syngas in industry by using a nickel catalyst. Nickel-based catalysts are the conventional catalysts in industrial applications due to their fast turnover rates, good availability, and low costs, however, limited by their tendency towards coke formation. In this study, a detailed surface reaction mechanism is developed for steam reform-ing of methane over nickel and results are compared with the reference data. Y1 - 2022 UR - https://www.researchgate.net/publication/361279412_Thermodynamic_analysis_to_develop_a_detailed_surface_reaction_mechanism ER - TY - GEN A1 - Franken, Tim A1 - Srivastava, Vivek A1 - Lee, Sung-Yong A1 - Heuser, Benedikt A1 - Shrestha, Krishna Prasad A1 - Seidel, Lars A1 - Mauß, Fabian ED - Xandra, Margot ED - Payri, Raúl ED - Serrano, José Ramón T1 - Numerical Analysis of the Combustion of Diesel, Dimethyl Ether, and Polyoxymethylene Dimethyl Ethers (OMEn, n=1-3) Using Detailed Chemistry T2 - THIESEL 2022 : Conference on Thermo- and Fluid-Dynamics of Clean Propulsion Powerplants, 13th-16th September 2022 : conference proceedings N2 - New types of synthetic fuels are introduced in internal combustion engine applications to achieve carbon-neutral and ultra-low emission combustion. Dimethyl Ether (DME) and Polyoxymethylene Dimethyl Ethers (OMEn) belong to such kind of synthetic fuels. Recently, Shrestha et al. (2022) have developed a novel detailed chemistry model for OMEn (n=1-3) to predict the ignition delay time, laminar flame speed and species formation for various thermodynamic conditions. The detailed chemistry model is applied in the zero dimensional (0D) stochastic reactor model (DI-SRM) to investigate the non-premixed combustion in a 2-liter diesel engine. Further insights in the formation of unburned hydrocarbons (HC), carbon monoxide and nitrogen oxides during the combustion of OMEn fuels are obtained in this work. The combustion and emission formation of DME and OMEn (n=1-3) are investigated and compared to conventional Diesel combustion. The mixture formation is governed by an earlier vaporization of the DME and OMEn fuels, faster homogenization of the respective air-fuel mixture and higher reactivity. At the same injection pressure, the OMEn fuels obtain higher NOx but lower CO and HC emissions. High amounts of aromatics, ethene, methane formaldehyde and formic acid are found within the Diesel exhaust gas. The DME and OMEn exhaust gas contains higher fractions of formaldehyde and formic acid, and fractions of methane, methyl formate and nitromethane. KW - Polyoxymethylene Dimethyl Ethers KW - Stochastic Reactor Model KW - Detailed Chemistry KW - Modelling KW - Emissions Y1 - 2022 UR - https://www.lalibreria.upv.es/portalEd/UpvGEStore/products/p_6328-1-1 SN - 978-84-1396-055-5 U6 - https://doi.org/10.4995/Thiesel.2022.632801 PB - Editorial Universitat Politècnica de València CY - València ER - TY - GEN A1 - Franken, Tim A1 - Shrestha, Krishna Prasad A1 - Seidel, Lars A1 - Mauß, Fabian ED - Sens, Marc T1 - Effect of Gasoline–Ethanol–Water Mixtures on Auto-Ignition in a Spark Ignition Engine T2 - International Conference on Knocking in Gasoline Engines N2 - The climate protection plan of the European Union requires a significant reduction of CO2 emissions from the transportation sector by 2030. Today ethanol is already blended by 10vol-% in gasoline and further increase of the ethanol content to 20vol-% is discussed. During the ethanol production process, distillation and molecular sieving is required to remove the water concentration to achieve high-purity ethanol. However, hydrous ethanol can be beneficial to suppress knock of spark ignition engines. The hygroscopic nature of ethanol can allow to increase the water content in gasoline – water emulsions even more, without adding additional surfactants, and improve the thermal efficiency by optimized combustion phasing, while keeping the system complexity low. Hence, the effect of gasoline – ethanol – water mixtures on the auto-ignition in a single-cylinder spark ignition engine is investigated by using multi-dimensional simulation and detailed chemistry. The gasoline – ethanol mixtures are defined to keep the Research Octane Number constant, while the Motored Octane Number is decreasing. In total five surrogates are defined and investigated: E10 (10vol-% ethanol-in-gasoline), E20, E30, E70 and E100. The water content is determined according to experimentally defined ternary diagrams that evaluated stable gasoline – ethanol – water emulsion at different gasoline – ethanol blending ratios. The auto-ignition modes of the surrogates are analyzed using the diagram, which determines if hotspots are within harmless deflagration or harmful developing detonation regime. The strongest auto-ignition is observed for the E10 surrogate, while increasing ethanol content reduces the surrogate reactivity and increases the resonance parameter. No auto-ignition of the unburnt mixture is observed for the E70 and E100 surrogates. The addition of hydrous ethanol decreased the excitation time of the surrogates, especially at low ethanol content, wherefor the reactivity parameter is significantly increased. The hotspots for E10, E20 and E30 surrogates with hydrous ethanol are found within the developing detonation regime, while hotspots of the E70 surrogate with hydrous ethanol are found in the transition regime. For the hydrous E100 surrogate no auto-ignition is predicted because of reduced temperature of the unburnt mixture due to water vaporization, which outweighs the increased reactivity due to water vapor addition. KW - Knock KW - Gasoline KW - Ethanol KW - Simulation KW - Detailed Chemistry KW - Spark Ignition Y1 - 2022 SN - 978-3-8169-3544-5 U6 - https://doi.org/10.24053/9783816985440 SP - 175 EP - 222 PB - expert CY - Tübingen ER - TY - GEN A1 - Giri, Binod Raj A1 - Shrestha, Krishna Prasad A1 - Mai, Tam V.-T. A1 - Giri, Sushant A1 - Adil, Mohammad A1 - Naik, R. Thirumaleswara A1 - Mauß, Fabian A1 - Huynh, Lam Kim T1 - A Theoretical Study of NH2 Radical Reactions with Propane and Its Kinetic Implications in NH3-Propane Blends’ Oxidation T2 - Energies N2 - The reaction of NH2 radicals with C3H8 is crucial for understanding the combustion behavior of NH3/C3H8 blends. In this study, we investigated the temperature dependence of the rate coefficients for the hydrogen abstraction reactions of C3H8 by NH2 radicals using high-level theoretical approaches. The potential energy surface was constructed at the CCSD(T)/cc-pV(T, Q)//M06-2X/aug-cc-pVTZ level of theory, and the rate coefficients were computed using conventional transition state theory, incorporating the corrections for quantum tunneling and hindered internal rotors (HIR). The computed rate coefficients showed a strong curvature in the Arrhenius behavior, capturing the experimental literature data well at low temperatures. However, at T > 1500 K, the theory severely overpredicted the experimental data. The available theoretical studies did not align with the experiment at high temperatures, and the possible reasons for this discrepancy are discussed. At 300 K, the reaction of NH2 with C3H8 predominantly occurs at the secondary C-H site, which accounts for approximately 95% of the total reaction flux. However, the hydrogen abstraction reaction at the primary C-H site becomes the dominant reaction above 1700 K. A composite kinetic model was built, which incorporated the computed rate coefficients for NH2 + C3H8 reactions. The importance of NH2 + C3H8 reactions in predicting the combustion behavior of NH3/C3H8 blends was demonstrated by kinetic modeling. Y1 - 2023 U6 - https://doi.org/10.3390/en16165943 SN - 1996-1073 VL - 16 IS - 16 ER - TY - GEN A1 - Elbaz, Ayman M. A1 - Giri, Binod Raj A1 - Shrestha, Krishna Prasad A1 - Arab, Omar Z. A1 - Farooq, Aamir A1 - Mauß, Fabian A1 - Roberts, William L. T1 - A comprehensive experimental and kinetic modeling study of laminar flame propagation of ammonia blended with propene T2 - Combustion and Flame N2 - Enhancement of ammonia reactivity is crucial for potential applications of ammonia as an engine and gas turbine fuel. A common strategy for improving ammonia's poor reactivity is blending it with more reactive fuels like hydrogen and methane. However, fundamental studies of ammonia combustion with higher hydrocarbons and key intermediate oxidation species of higher alkanes such as propene do not exist. Thus, this work presents an effort to study the laminar flame propagation of ammonia blended with propene. Laminar burning velocity (SL) of NH3/C3H6/air mixtures was measured at 298 K, pressures up to 5 bar, equivalence ratios of 0.7 to 1.3, and various propene to ammonia ratios (i.e.,% propene to ammonia mole fraction, xC3H6 = 10 to 50) in a high-pressure spherical propagating flame vessel. A kinetic model was developed based on our previous work to characterize the combustion behavior of NH3/C3H6/air mixture. The model reasonably agrees with the experimental data and follows the observed trends very well. The results showed that blending NH3 with C3H6 positively enhanced SL of NH3 by promoting the formation of key radicals e.g., O, OH, and H. Relative to a neat ammonia/air mixture, co-firing ammonia with propene leads to a reduced pressure dependence of the laminar burning velocity. However, the reaction H + O2(+M)=HO2(+M) leads to strong pressure dependency of lean NH3/C3H6 mixtures compared to rich mixtures. The model reveals that besides fuel-NO coming from NH3, prompt NO also actively contributes to NO formation. It is seen that N2O formation is significantly suppressed with increasing pressure or increasing C3H6 content in the fuel blend. In contrast to NO and N2O, NO2 concentration increases slightly with an increase in pressure. The reported experimental data and model will be useful in understanding the interaction between NH3 and alkenes. Y1 - 2023 U6 - https://doi.org/10.1016/j.combustflame.2023.112791 SN - 0010-2180 VL - 253 ER - TY - GEN A1 - Shrestha, Krishna Prasad A1 - Mai, Tam V.-T. A1 - Giri, Sushant A1 - Giri, Binod Raj A1 - Huynh, Lam Kim A1 - Mauss, Fabian T1 - Reaction Kinetics of NH2 Radicals with Dimethyl Ether (DME) and Diethyl Ether (DEE) and Their Implications in NH3-DME/DEE blend modeling T2 - Los Alamos National Laboratory (LANL) N2 - The reactions of amino radicals (NH2) play a vital role in governing the combustion behaviour of various nitrogen-rich chemical systems such as ammonia, coal nitrogen gasification, and biomass. Ammonia has recently gained considerable attention in the combustion community. Since it is a carbon-free fuel, it can help combat global warming by decarbonizing the energy sectors. However, several reports in the literature highlight the importance of the NH3-dual fuel approach to boost the combustion properties of neat ammonia. For combustion modeling of NH3-dual fuel systems, accurate knowledge of the cross-reactions between the nitrogen and carbon family is very critical. Several earlier studies have shown the influence of NH2 radical reactions with the fuel (combustion promoter) in accurately predicting the low- temperature combustion behaviour of NH3-dual fuels (see Giri et al. and references cited therein). The reactions of NH2 radicals are not only important in the combustion environment but also, they are relevant to the chemistry of planetary atmospheres. In this work, we investigated the hydrogen abstraction reactions of NH2 radials with dimethyl ether (DME) and diethyl ether (DEE) using a high-level quantum method combined with the statistical rate theory. We implemented the derived rate coefficients in our kinetic model to identify its effect in the combustion modeling of NH3-DME/DEE blends. Y1 - 2023 UR - https://www.osti.gov/biblio/1987392 IS - LA-UR-23-26969 ER - TY - GEN A1 - Giri, Binod Raj A1 - Shrestha, Krishna Prasad A1 - Mai, Tam V.-T. A1 - Mauß, Fabian A1 - Huynh, Lam Kim T1 - A theoretical kinetic study of the reactions of NH2 radicals with methanol and ethanol and their implications in kinetic modeling T2 - International Journal of Chemical Kinetics N2 - Amino (NH2) radicals play a central role in the pyrolysis and oxidation of ammonia. Several reports in the literature highlight the importance of the reactions of NH2 radicals with fuel in NH3-dual-fuel combustion. Therefore, we investigated the reactions of NH2 radicals with methanol (CH3OH) and ethanol (C2H5OH) theoretically. We explored the various reaction pathways by exploiting CCSD(T)/cc-pV(T, Q)Z//M06-2X/aug-cc-pVTZ level of theory. The reaction proceeds via complex formation at the entrance and exit channels in an overall exothermic process. We used canonical transition state theory to obtain the high-pressure limiting rate coefficients for various channels over the temperature range of 300–2000 K. We discerned the role of various channels in the potential energy surface (PES) of NH2 + CH3OH/C2H5OH reactions. For both reactions, the hydrogen abstraction pathway at the OH-site of alcohols plays a minor role in the entire T-range investigated. By including the title reactions into an extensive kinetic model, we demonstrated that the reaction of NH2 radicals with alcohols plays a paramount role in accurately predicting the low-temperature oxidation kinetics of NH3-alcohols dual fuel systems (e.g., shortening the ignition delay time). On the contrary, these reactions have negligible importance for high-temperature oxidation kinetics of NH3-alcohol blends (e.g., not affecting the laminar flame speed). In addition, we calculated the rate coefficients for NH2 + CH4 = CH3 + NH3 reaction that are in excellent agreement with the experimental data. Y1 - 2023 U6 - https://doi.org/10.1002/kin.21609 SN - 0538-8066 VL - 55 IS - 1 SP - 3 EP - 14 ER - TY - GEN A1 - Shrestha, Krishna Prasad A1 - Eckart, Sven A1 - Drost, Simon A1 - Fritsche, Chris A1 - Schießl, Robert A1 - Seidel, Lars A1 - Maas, Ulrich A1 - Krause, Hartmut A1 - Mauß, Fabian T1 - A comprehensive kinetic modeling of oxymethylene ethers (OMEn, n= 1–3) oxidation-laminar flame speed and ignition delay time measurements T2 - Combustion and Flame N2 - This work reports on the development and experimental validation of a detailed reaction mechanism for the oxidation of polyoxymethylene dimethyl ethers (OMEn, n = 1–3). The validation is done by constant-volume chamber laminar flame speeds (393 K and 443 K, 1 to 5 bar, and equivalence ratio 0.8 to 1.6) and Rapid Compression Machine ignition delay times (550–680 K, 10 and 15 bar, equivalence ratios of 0.5–2.0) in OMEn/air mixtures. Using our new experimental and published data, the validation basis for the new kinetic model comprises the pyrolysis and oxidation of OMEn (n = 1–3) in freely propagating flames, auto-ignition in rapid compression machines and shock tubes, and speciation in jet-stirred and flow reactors as well as burner-stabilized premixed flames. The model provides a reasonable agreement with the experimental data for a broad range of conditions investigated. The performance of the developed model is compared against the recent literature models. OMEn (n = 1–3) all have the same laminar flame speed. The model suggests that the chemistry of OME0 (DME) and CH3OCHO (methyl formate) is the one that dictates the flame chemistry. Under the same pressure and equivalence ratio conditions, ignition delay times of OME2 and OME3 are similar for the investigated temperature range. This work helps to improve the understanding of OMEs chemistry. The model developed in this work will serve as the base mechanism for higher chain length OMEs (n>3). Y1 - 2022 U6 - https://doi.org/10.1016/j.combustflame.2022.112426 SN - 1556-2921 SN - 0010-2180 VL - 246 ER - TY - GEN A1 - Shrestha, Krishna Prasad A1 - Elbaz, Ayman M. A1 - Giri, Binod Raj A1 - Arab, Omar Z. A1 - Adil, Mohammad A1 - Seidel, Lars A1 - Roberts, William L. A1 - Farooq, Aamir A1 - Mauß, Fabian T1 - Experimental and Kinetic Modeling Study of 1, 3-Dioxolane Oxidation and Comparison with Dimethoxymethane T2 - Energy & Fuels N2 - This work reports laminar flame speeds and ignition delay times of 1,3-dioxolane/O2/inert gases over a wide range of conditions. Laminar flame speeds were determined experimentally at pressures of 1 and 3 bar, the temperature of 300 K, and equivalence ratios ranging from 0.7 to 1.4 using a constant-volume spherical chamber, whereas ignition delay times were measured in a shock tube at a pressure of 1 bar, the temperature range of 1000–1265 K, and equivalence ratios of 0.5 and 1.0. A detailed kinetic model is developed to predict the oxidation of 1,3-dioxolane utilizing our new experimental data and published datasets on the oxidation of 1,3-dioxolane in freely propagating flames, autoignition in rapid compression machines and shock tubes, and speciation in a jet-stirred reactor. Model predictions are in reasonable agreement with the experimental data. Laminar flame speeds and ignition delay times of 1,3-dioxolane (cyclic ether) are compared with those of dimethoxymethane (acyclic ether). It is found that 1,3-dioxolane has a higher laminar flame speed than that of dimethoxymethane, which may be attributed to the formation of C2H4, C2H2, and the H atom from 1,3-dioxolane. On the contrary, ignition delay times of 1,3-dioxolane are longer than those of dimethoxymethane below 1000 K and shorter above 1000 K for the same dilution level. The reaction ȮCHO = CO2 + H is critical for accurately predicting 1,3-dioxolane oxidation, and it significantly influences model predictions under low-pressure conditions. The model developed in this work will serve as the base mechanism for higher cyclic and acyclic ethers. Y1 - 2022 U6 - https://doi.org/10.1021/acs.energyfuels.2c01132 SN - 1520-5029 SN - 0887-0624 VL - 36 IS - 14 SP - 7744 EP - 7754 ER - TY - GEN A1 - Rossi, Edoardo A1 - Bargende, Michael A1 - Kulzer, André Casal A1 - Chiodi, Marco A1 - Massoud, Ehab A1 - Shrestha, Krishna Prasad A1 - Mauß, Fabian T1 - Analysis of the applicability of Water Injection in Combination with an eFuel for Knock Mitigation and Improved Engine Efficiency T2 - SAE Technical Paper N2 - The development of future gasoline engines is dominated by the study of new technologies aimed at reducing the engine negative environmental impact and increase its thermal efficiency. One common trend is to develop smaller engines able to operate in stoichiometric conditions across the whole engine map for better efficiency, lower fuel consumption, and optimal conversion rate of the three-way catalyst (TWC). Water injection is one promising technique, as it significantly reduces the engine knock tendency and avoids fuel enrichment for exhaust temperature mitigation at high power operation. With the focus on reducing the carbon footprint of the automotive sector, another vital topic of research is the investigation of new alternative CO2-neutral fuels or so-called eFuels. Several studies have already shown how these new synthetic fuels can be produced by exploiting renewable energy sources and can significantly reduce engine emissions. This work is part of the FVV project number 1367, “Water Injection in Spark-Ignition Engines II”, which investigates the coexistence of two different engine technologies that heads towards the same direction of sustainability of the internal combustion engine: water injection and eFuels. The goal is to assess the advantages that the adoption of an eFuel in combination with water injection strategies can bring, with respect to the same strategies applied in combination with commercial gasoline. Several water injection strategies, including direct water injection, indirect water injection, injection timing, and pressure variations, are considered for a better understanding of the benefits brought by the combination of an eFuel with water injection. For this purpose, experimental tests and 3D-CFD engine simulations have been performed. The physical properties of the investigated eFuel have been experimentally measured for accurate modelling in the simulation environment, and the thermodynamic properties have been evaluated utilizing detailed chemistry calculations. Y1 - 2022 U6 - https://doi.org/10.4271/2022-37-0019 SN - 2688-3627 SN - 0148-7191 ER - TY - GEN A1 - Franken, Tim A1 - Seidel, Lars A1 - Gonzalez Mestre, Laura Catalina A1 - Shrestha, Krishna Prasad A1 - Matrisciano, Andrea A1 - Mauss, Fabian T1 - Assessment of Auto-Ignition Tendency of Gasoline, Methanol, Toluene and Hydrogen Fuel Blends in Spark Ignition Engines T2 - THIESEL 2020 Conference on Thermo-and Fluid Dynamic Processes in Direct Injection Engines N2 - State of the art spark ignited gasoline engines achieve thermal efficiencies above 46 % e.g. due to friction optimized crank trains, high in-cylinder tumble flow and direct fuel injection. Further improvements of thermal efficiency are expected from lean combustion, higher compression ratio and new knock-resistant fuel blends. One of the limitations to these improvements are set by the autoignition in the end gas, which can develop to knocking combustion and severely damage the internal combustion engine. The auto-ignition is enhanced by high cylinder gas temperatures and reactive species in the end gas composition. Quasi-dimensional Stochastic Reactor Model simulations with detailed chemistry allow to consider the thermochemistry properties of surrogates and complex end gas compositions. Based on the detailed reaction scheme and surrogate model, an innovative tabulated chemistry approach is utilized to generate dual-fuel laminar flame speed and combustion chemistry look-up tables. This reduces the simulation duration to seconds per cycle, while the loss in accuracy compared to solving the chemistry “online” is marginal. The auto-ignition events predicted by the tabulated chemistry simulation are evaluated using the Detonation Diagram developed by Bradley and co-workers. This advanced methodology for quasi-dimensional models evaluates the resonance between the shock wave and reactionfront velocity from auto-ignition in the end gas and determines if it is a harmful developing detonation or normal deflagration. The aim of this work is to evaluate the auto-ignition characteristics of different fuel blends. The Stochastic Reactor Model with tabulated chemistry is applied to perform a numerical analysis of the autoignition of the fuel blends and operating conditions. Experimental measurements of a single cylinder research engine operated with RON95 E10 fuel are used to train and validate the simulation model. The RON95 E10 fuel is blended with Methanol, Hydrogen and Toluene. The knock tendency based on the evaluation of auto-ignition events of the different fuel blends are analysed for three operating points at 1500 rpm 15 bar IMEP, 2000 rpm 20 bar IMEP and 2500 rpm 15 bar IMEP with advanced spark timings. Y1 - 2020 UR - https://hal.science/hal-03573870 ER - TY - GEN A1 - Manna, Maria Virginia A1 - Sabia, Pino A1 - Shrestha, Krishna Prasad A1 - Seidel, Lars A1 - Ragucci, Raffaele A1 - Mauß, Fabian A1 - De Joannon, Mara T1 - NH3NO interaction at low-temperatures: an experimental and modeling study T2 - Proceedings of the Combustion Institute N2 - The present work provides new insight into NH3single bondNO interaction under low-temperature conditions. The oxidation process of neat NH3 and NH3 doped with NO (450, 800 ppm) was experimentally investigated in a Jet Stirred Flow Reactor at atmospheric pressure for the temperature range 900–1350 K. Results showed NO concentration is entirely controlled by DeNOx reactions in the temperature range 1100–1250 K, while NH3single bondNO interaction does not develop through a sensitizing NO effect, for these operating conditions. A detailed kinetic model was developed by systematically updating rate constants of controlling reactions and declaring new reactions for N2H2 isomers (cis and trans). The proposed mechanism well captures target species as NO and H2 profiles. For NH3single bondNO mixtures, NO profiles were properly reproduced through updated DeNOx chemistry, while NH2 recombination reactions were found to be essential for predicting the formation of H2. The role of ammonia as a third-body species is implemented in the updated mechanism, with remarkable effects on species predictions. For neat NH3 mixture, the reaction H+O2(+M)=HO2(+M) was crucial to predict NO formation via the reaction NH2+HO2double bondH2NO+OH. Y1 - 2023 U6 - https://doi.org/10.1016/j.proci.2022.09.027 SN - 1873-2704 VL - 39 IS - 1 SP - 775 EP - 784 ER - TY - GEN A1 - Mai, Tam V.-T. A1 - Bui, Thanh Q. A1 - Nhung, Nguyen Thi Ai A1 - Quy, Phan Tu A1 - Shrestha, Krishna Prasad A1 - Mauß, Fabian A1 - Giri, Binod Raj A1 - Huynh, Lam Kim T1 - An Ab Initio RRKM-Based Master Equation Study for Kinetics of OH-Initiated Oxidation of 2-Methyltetrahydrofuran and Its Implications in Kinetic Modeling T2 - Energies N2 - Cyclic ethers (CEs) can be promising future biofuel candidates. Most CEs possess physico-chemical and combustion indicators comparable to conventional fuels, making them suitable for internal combustion engines. This work computationally investigates the kinetic behaviors of hydrogen abstraction from 2-methyl tetrahydrofuran (2MTHF), one of the promising CEs, by hydroxyl radicals under combustion and atmospheric relevant conditions. The various reaction pathways were explored using the CCSD(T)/cc-pVTZ//M06-2X/aug-cc-pVTZ level of theory. The Rice–Ramsperger–Kassel–Marcus-based master equation (RRKM-ME) rate model, including treatments for hindered internal rotation and tunneling, was employed to describe time-dependent species profiles and pressure and temperature-dependent rate coefficients. Our kinetic model revealed that the H-abstraction proceeds via an addition-elimination mechanism forming reaction complexes at both the entrance and exit channels. Eight different reaction channels yielding five radical products were located. The reaction exhibited complex kinetics yielding a U-shaped Arrhenius behavior. An unusual occurrence of negative temperature dependence was observed at low temperatures, owing to the negative barrier height for the hydrogen abstraction reaction from the C-H bond at the vicinity of the O-atom. A shift in the reaction mechanism was observed with the dominance of the abstraction at Cα-H of 2MTHF ring (causing negative-T dependence) and at CH3 (positive-T dependence) at low and high temperatures, respectively. Interestingly, the pressure effect was observed at low temperatures, revealing the kinetic significance of the pre-reaction complex. Under atmospheric pressure, our theoretical rate coefficients showed excellent agreement with the available literature data. Our model nicely captured the negative temperature-dependent behaviors at low temperatures. Our predicted global rate coefficients can be expressed as k (T, 760 Torr) = 3.55 × 101 × T−4.72 × exp [−340.0 K/T] + 8.21 × 10−23 × T3.49 × exp [918.8 K/T] (cm3/molecule/s). Our work provides a detailed kinetic picture of the OH-initiated oxidation kinetics of 2MTHF. Hence, this information is useful for building a kinetic me chanism for methylated cyclic ethers. KW - ab initio KW - RRKM-ME calculations KW - 2-methyl tetrahydrofuran KW - OH radicals KW - kinetic modeling Y1 - 2023 U6 - https://doi.org/10.3390/en16093730 SN - 1996-1073 VL - 16 IS - 9 ER - TY - GEN A1 - Giri, Binod Raj A1 - Palacios, Manuel Monge A1 - Thangaraj, Ravikumar A1 - Shrestha, Krishna Prasad A1 - Viskolcz, Béla A1 - Mauss, Fabian A1 - Szőri, Milán T1 - An Ab initio based OH initiated oxidation kinetics of glycerol carbonate: A promising biofuel component T2 - Proceedings of the Combustion Institute N2 - The global energy demand is steadily increasing because of the population explosion and economic growth. Fossil fuels supply around 85 % of global primary energy demand. On one hand, fulfilling the increasing energy demands is a big challenge for the next few decades. On the other hand, the continued burning of fossil fuels leads to higher CO2 emissions, severely impacting global warming. Therefore, the policymakers vow to shift from conventional fuels to renewable resources for economic, environmental, and future energy security reasons. In this context, biofuels from lignocellulosic biomass and/or carbon-neutral fuels produced in the sustainable carbon cycle can close the carbon cycle and reach net zero-carbon emission. Recently, glycerol carbonate has been proposed as a promising fuel or fuel additive for future sustainability. Therefore, we investigated the hydrogen abstraction reactions of glycerol carbonate (GC) by OH radicals using high-level ab initio and variational transition state theory calculations. We mapped out the potential energy surface using the CCSD(T)/cc-pV(D, T)Z//MP2/cc-pVTZ level of theory. We used the ab initio parameters to obtain the site-specific rate coefficients by employing the variational transition state theory. We observed that every hydrogen atom in GC displays a unique reactivity with OH radicals. We derived branching ratio of each channel that are difficult to access experimentally. The overall rate coefficients exhibit a strong non-Arrhenius behaviour, which can be represented as: This is the first reported rate data for the glycerol carbonate and OH radicals reaction. Y1 - 2024 UR - https://www.sciencedirect.com/science/article/abs/pii/S1540748924004760 U6 - https://doi.org/10.1016/j.proci.2024.105668 VL - 40 SP - 1 EP - 8 PB - Elsevier ER - TY - GEN A1 - Rakhi, Rakhi A1 - Shrestha, Krishna Prasad A1 - Günther, Vivien A1 - Mauß, Fabian T1 - Kinetically consistent detailed surface reaction mechanism for steam reforming of methane over nickel catalyst T2 - Reaction Kinetics, Mechanisms and Catalysis KW - Nickel-based catalyst KW - Kinetic consistency KW - Thermodynamic analysis KW - Steam reforming KW - Detailed surface reaction mechanism Y1 - 2022 UR - https://link.springer.com/article/10.1007/s11144-022-02314-7 U6 - https://doi.org/10.1007/s11144-022-02314-7 SN - 1878-5204 SN - 1878-5190 VL - 135 IS - 6 SP - 3059 EP - 3083 ER - TY - GEN A1 - Shrestha, Krishna Prasad A1 - Mai, Tam V.‐T. A1 - Giri, Sushant A1 - Reddy, V. Mahendra A1 - Szőri, Milán A1 - Verma, Rakhi A1 - Mauss, Fabian A1 - Giri, Binod Raj A1 - Huynh, Lam Kim T1 - Reaction kinetics of NH₂ with H₂CO and CH₃CHO : modeling implications for NH₃‐dual fuel blends T2 - International journal of chemical kinetics N2 - Carbon‐free fuels like ammonia (NH₃) and hydrogen (H₂) offer significant potential in combating global warming by reducing greenhouse gas emissions and moving toward zero carbon emissions. Over the past few years, our research has focused on understanding the combustion behavior of carbon‐neutral and carbon‐free fuels. In particular, we have explored the combustion characteristics of NH₃ when blended with various hydrocarbons and oxygenates. Our investigation revealed that carbon‐nitrogen cross‐chemistry plays a crucial role in shaping the combustion properties of NH3‐hydrocarbon/oxygenate blends. Specifically, the chemistry of amino (NH₂) radicals is vital in influencing the low‐temperature reactivity of these blends. Understanding the interactions between carbon and nitrogen is essential for optimizing combustion processes and improving the emissions profile of NH₃‐based fuels. Recognizing the significance of this cross‐chemistry, we investigated the reaction kinetics of NH₂ radicals with formaldehyde (H₂CO) and acetaldehyde (CH₃CHO) using high‐level ab initio and transition state theory calculations. We computed the potential energy profiles of these reactions at the CCSD(T)/CBS//M06‐2X/aug‐cc‐pVTZ level of theory to analyze the reactivity of NH2 radicals at various C─H bond sites. The newly derived rate constants have proven to be highly sensitive for modeling the low‐temperature oxidation of NH₃‐dual fuel blends, significantly enhancing the predictive accuracy of our previously published kinetic models. This work offers valuable insights into the role of NH₂ radicals, thereby advancing the development of NH₃‐dual fuel systems. Y1 - 2025 U6 - https://doi.org/10.1002/kin.21781 SN - 0538-8066 SN - 1097-4601 VL - 57 IS - 7 SP - 403 EP - 416 PB - Wiley CY - New York ER - TY - GEN A1 - Giri, Binod Raj A1 - Mai, Tam V.‐T. A1 - Shrestha, Krishna Prasad A1 - Giri, Sushant A1 - Naik, R. Thirumaleswara A1 - Verma, Rakhi A1 - Mauss, Fabian A1 - Huynh, Lam K. T1 - Theoretical kinetic study of NH₂ reactions with dimethyl ether and diethyl ether : implications for kinetic modeling T2 - International journal of chemical kinetics N2 - Ammonia (NH₃) and hydrogen (H₂) have emerged as promising carbon‐free fuels to help mitigate global warming by reducing greenhouse gas emissions. Our ongoing research currently focuses on understanding the combustion characteristics of NH₃ blends with oxygenates and hydrocarbons, uncovering the critical role of carbon–nitrogen cross‐reactions in accurately modeling their combustion behavior. Amino (NH₂) radicals, which are abundant in ammonia and nitrogen‐rich environments, strongly influence the low‐temperature reactivity of NH₃‐hydrocarbon/oxygenate mixtures, affecting overall reactivity and emission characteristics. Recognizing the importance of NH₂ radicals, we investigated the reaction kinetics of NH₂ with dimethyl ether (DME, CH₃OCH₃) and diethyl ether (DEE, CH₃CH₂OCH₂CH₃) using appropriate high‐level ab initio and statistical rate theory methods. We computed the potential energy profiles at the CCSD(T)/cc‐pV(T, Q)Z//M06‐2X/aug‐cc‐pVTZ level of theory, analyzing the reactivity of NH₂ radicals at various C─H sites of these diethers. Incorporating these newly derived rate parameters, our updated kinetic model successfully captures previous experimental data, addressing the modeling challenges encountered in our earlier studies. Our findings, including insights into the impact of NH₂ radicals, contribute to an understanding of ammonia combustion and its potential in achieving carbon‐neutral energy systems. KW - Diethyl ether KW - Dimethyl ether KW - Kinetic modeling KW - NH Y1 - 2025 U6 - https://doi.org/10.1002/kin.21779 SN - 0538-8066 SN - 1097-4601 VL - 57 IS - 6 SP - 353 EP - 363 PB - Wiley CY - Hoboken, NJ ER - TY - GEN A1 - Shrestha, Krishna Prasad A1 - Giri, Binod Raj A1 - Pelé, Ronan A1 - Aljohani, Khalid A1 - Brequigny, Pierre A1 - Mauss, Fabian A1 - Halter, Fabien A1 - Huynh, Lam K. A1 - Mounaïm-Rousselle, Christine T1 - A comprehensive chemical kinetic modeling and experimental study of NH₃−methanol/ethanol combustion towards net-zero CO₂ emissions T2 - Combustion and flame N2 - Ammonia is gaining attention as a green fuel with the potential to reduce carbon emissions. Its versatility allows it to be used directly in combustion engines, fuel cells, and as a hydrogen carrier, making it a key candidate for sustainable energy applications. This study provides a comprehensive analysis of the oxidation kinetics of ammonia (NH3) blends with methanol (CH3OH) and ethanol (C2H5OH) under diverse conditions. We measured laminar flame speeds of different NH3-alcohol blends — varying CH3OH/C2H5OH ratios (0–100 %) — using a constant volume combustion chamber across temperatures from 503 to 645 K and pressures of 2–11.3 bar. We also obtained the ignition delay times for NH3/C2H5OH blends with 10 % and 30 % (by mole) C2H5OH using a shock tube at pressures of 1, 10, and 20 bar and temperatures of 1100–1500 K. Our results show that incorporating CH3OH and C2H5OH into NH3 increases the laminar flame speed, with C2H5OH being a more effective promoter than CH3OH due to its higher contribution to the formation of reactive radicals (OH, H, and O). Our model suggests that at high temperatures, both CH3OH and C2H5OH contribute to increased NO formation, with C2H5OH being more effective in reducing N2O emissions than CH3OH. In shock tube experiments, adding C2H5OH significantly shortens ignition delay times of NH3. At low temperatures (in the rapid compression machine case), the sensitivity to ignition delay times decreases when the CH3OH/C2H5OH content exceeds 5 % in NH3-alcohol blends. C2H5OH is a more effective combustion promoter, enhancing NH3 reactivity and reducing NOx emission more efficiently than CH3OH. We developed a detailed kinetic model, building on our previous work, and validated it against new experimental and literature data. Our model accurately predicts the combustion behavior of neat NH3 and NH3 fuel blends and serves as a base for future research on NH3 blended with higher hydrocarbons and/or oxygenated blends. KW - Ammonia KW - Methanol KW - Ethanol KW - Kinetic modeling KW - Laminar flame speed KW - Ignition delay time Y1 - 2025 U6 - https://doi.org/10.1016/j.combustflame.2024.113954 SN - 0010-2180 VL - 274 SP - 1 EP - 21 PB - Elsevier BV CY - Amsterdam ER - TY - GEN A1 - Welp, Alexandra A1 - Rudolph, Charlotte A1 - Giri, Binod Raj A1 - Shrestha, Krishna Prasad A1 - Verma, Rakhi A1 - Mauss, Fabian A1 - Atakan, Burak T1 - Oxidation kinetics of ammonia methanol blends : an experimental and kinetic modeling study T2 - Combustion and flame N2 - Ammonia is emerging as a key hydrogen energy carrier for decarbonization. However, its low reactivity necessitates blending with hydrocarbons and/or oxygenates, such as alcohols, to improve combustion properties. Understanding the oxidation kinetics of such blends is essential for evaluating ammonia’s potential as a sustainable fuel. The experimental data on ammonia blended with simple alcohols like methanol remains scarce. This study investigates the oxidation kinetics of ammonia/methanol blends for the first time using a plug-flow reactor coupled with a time-of-flight mass spectrometer setup. This advanced setup enabled simultaneous quantification of temperature-dependent reactant conversion and product distribution over a temperature range of 373–973 K, a pressure of 3 bar, and equivalence ratios of 1 and 2. Adding 10 % methanol significantly enhances radical formation, reducing oxidation onset temperature compared to neat ammonia. Interestingly, the conversion onset temperature was only slightly influenced by the mixture composition or the equivalence ratio. The temperature dependence of the product distribution as a function of the equivalence ratio was further analyzed. Experimental results were compared to simulation using selected kinetic models from the literature, revealing significant disparities in predicting capabilities. Among the kinetic models, Shrestha 2025, He 2023 and Wang 2024 performed well, capturing our experimental data for NH3/CH3OH blends. Reaction flux and sensitivity analyses highlighted some key reactions involving the reactive combustion species (OH, HO2 and NH2), such as CH3OH+HO2 ⇌ CH2OH+H2O2 and CH3OH+NH2, governing the oxidation kinetics of NH3/CH3OH blends. This combined experimental and kinetic modeling approach provides valuable insights into fundamental reaction mechanisms of NH3/CH3OH blends, aiding the development of cleaner and more efficient combustion systems. KW - Ammonia KW - Methanol KW - Kinetic investigation KW - Plug-flow reactor KW - Mass spectrometry Y1 - 2025 U6 - https://doi.org/10.1016/j.combustflame.2025.114210 SN - 0010-2180 VL - 278 SP - 1 EP - 11 PB - Elsevier BV CY - Amsterdam ER -