TY - GEN A1 - Schmidt, Thomas A1 - Buß, Lars A1 - Ewert, Moritz A1 - Schönhoff, Gunnar A1 - Wehling, Tim Oliver A1 - Falta, Jens T1 - Adsorption of sulfur on Si(111) T2 - Surface Science N2 - The adsorption of S on Si(111)- 7 × 7 has been investigated for different preparation schemes and parameters. S was supplied from an electrochemical Ag2S cell. For room temperature adsorption and subsequent annealing, no ordered S induced reconstruction can be observed with spot profile analysis low-energy electron diffraction (SPALEED). S deposition at temperatures above about 400°C, however, leads to a well-ordered reconstruction. Judging from the LEED pattern, the same reconstruction was already observed by Metzner et al. [Surf. Sci. 377–379(1997) 71–74] who identified it as 4 × 4 reconstruction. The upper temperature limit for the pre-paration of this superstructure depends on S flux, which is needed to compensate for desorption. Prolonged S exposure leads to surface roughening, as observed with SPALEED and scanning tunneling microscopy (STM), pointing to surface etching by S. From our SPALEED data, we can conclude that the observed reconstruction is not a 4 × 4 reconstruction, but a 20/12 superstructure with a rectangular unit cell that exists in three rotational domains, as confirmed by STM. Different structural trial models have been assessed with density functional theory. Among these model structures, a configuration with dimers adsorbed on bridging sites, with a S coverage of 1 monolayer, is most likely, since it is energetically favorable and is in agreement with all experimental results. KW - Passivation KW - Low-energy electron diffraction KW - Scanning tunneling microscopy KW - Density functional theory KW - Auger electron spectroscopy Y1 - 2020 U6 - https://doi.org/10.1016/j.susc.2019.121561 SN - 0039-6028 SN - 1879-2758 VL - 694 ER - TY - GEN A1 - Fügenschuh, Armin A1 - Geißler, Björn A1 - Gollmer, Ralf A1 - Hayn, Christine A1 - Henrion, René A1 - Hiller, Benjamin A1 - Humpola, Jesco A1 - Koch, Thorsten A1 - Lehmann, Thomas A1 - Martin, Alexander A1 - Mirkov, Radoslava A1 - Morsi, Antonio A1 - Rövekamp, Jessica A1 - Schewe, Lars A1 - Schmidt, Martin A1 - Schultz, Rüdiger A1 - Schwarz, Robert A1 - Schweiger, Jonas A1 - Stangl, Claudia A1 - Steinbach, Marc C. A1 - Willert, Bernhard M. T1 - Mathematical Optimization for Challenging Network Planning Problems in Un- bundled Liberalized Gas Markets T2 - Energy Systems Y1 - 2014 U6 - https://doi.org/10.1007/s12667-013-0099-8 SN - 1868-3975 SN - 1868-3967 VL - 5 IS - 3 SP - 449 EP - 473 ER - TY - GEN A1 - Krisponeit, Jon-Olaf A1 - Fischer, Simon A1 - Esser, Sven A1 - Moshnyaga, Vasily A1 - Schmidt, Thomas A1 - Piper, Louis F. J. A1 - Flege, Jan Ingo A1 - Falta, Jens T1 - The morphology of VO2/TiO2(001): terraces, facets, and cracks T2 - Scientific Reports N2 - Vanadium dioxide (VO2) features a pronounced, thermally-driven metal-to-insulator transition at 340 K. Employing epitaxial stress on rutile TiO2(001) substrates, the transition can be tuned to occur close to room temperature. Striving for applications in oxide-electronic devices, the lateral homogeneity of such samples must be considered as an important prerequisite for efforts towards miniaturization. Moreover, the preparation of smooth surfaces is crucial for vertically stacked devices and, hence, the design of functional interfaces. Here, the surface morphology of VO2/TiO2(001) films was analyzed by low-energy electron microscopy and diffraction as well as scanning probe microscopy. The formation of large terraces could be achieved under temperature-induced annealing, but also the occurrence of facets was observed and characterized. Further, we report on quasi-periodic arrangements of crack defects which evolve due to thermal stress under cooling. While these might impair some applicational endeavours, they may also present crystallographically well-oriented nano-templates of bulk-like properties for advanced approaches. KW - Vanadium dioxide (VO2) KW - rutile TiO2(001) KW - metal-to-insulator transition KW - morphology KW - crystallography KW - low-energy electron microscopy (LEEM) KW - low-energy electron diffraction (LEED) KW - scanning probe microscopy Y1 - 2020 U6 - https://doi.org/10.1038/s41598-020-78584-9 SN - 2045-2322 VL - 10 ER - TY - GEN A1 - Sharma, Sparsh A1 - Geyer, Thomas A1 - Sarradj, Ennes A1 - Schmidt, Heiko T1 - Experimental validation of a lower-order model for leading-edge noise based on vortex method T2 - 27th AIAA/CEAS Aeroacoustics Conference 2021, Virtual Event, August 2 - 6 2021 Y1 - 2021 U6 - https://doi.org/10.2514/6.2021-2250 ER - TY - GEN A1 - Bleicher, Achim A1 - Schauer, Thomas A1 - Jirasek, Robert A1 - Höltke, Tim A1 - Zhang, Yangwen A1 - Marker, Paul A1 - Wulff, Wulf A1 - Manfrecola, Johannes A1 - Schmidt, Therese T1 - Hybride Konstruktionen an der BTU Cottbus-Senftenberg T2 - Bautechnik N2 - Die angestrebten Ziele einer Ressourcen- und Klimaneutralität erfordern ein radikaleres Umdenken der Bauschaffenden, das mit einer noch viel stärkeren Sensibilisierung der Auftraggeber für die Auswirkungen des Material- und Energieverbrauchs im Bausektor verbunden ist. Ein Ansatz, um diese Ziele zu erreichen, sind hybride Konstruktionen, in denen unterschiedliche Materialien, Elemente, Funktionen und Technologien auf mehreren Konstruktionsebenen ressourcen- und energieeffizient kombiniert sowie im Fall eines Rückbaus sortenrein rezykliert werden. Dieser anspruchsvolle Ansatz ist von Beginn an erklärtes Ziel des Lehrstuhls Hybride Konstruktionen – Massivbau an der BTU Cottbus-Senftenberg und zieht sich durch alle Lehr- und Forschungsaktivitäten. Mit ausgewählten Forschungsprojekten werden Motivation und Methoden hybrider Konstruktionen sowie deren Potenzial für ressourcen- und klimaneutrale Konstruktionen anhand von Prototypen aufgezeigt. Hierbei steht neben der ökologischen Weiterentwicklung klassischer hybrider Konstruktionen aus nachwachsenden und rezyklierten Rohstoffen, bspw. Holz und Recyclingbeton, auch die Entwicklung aktiver hybrider Konstruktionen im Fokus. Die gezielte Integration von aktiven Technologien wie Sensorik, Aktuatorik und Regelungstechnik ermöglicht multifunktionale Konstruktionen, einen hohen Nutzungskomfort, einen geringeren Rohstoffverbrauch bis hin zur Energiegewinnung aus dynamischen Einwirkungen. Y1 - 2021 UR - https://onlinelibrary.wiley.com/doi/abs/10.1002/bate.202100056 U6 - https://doi.org/10.1002/bate.202100056 SN - 1437-0999 VL - 98 IS - 12 SP - 907 EP - 920 ER - TY - GEN A1 - Schmidt, Carsten A1 - Borcherding, Heike A1 - Thiele, Thomas A1 - Schedler, Uwe A1 - Werner, Franziska A1 - Rödiger, Stefan A1 - Roggenbuck, Dirk A1 - Schierack, Peter T1 - Fluorescence-encoded poly (methyl metharcylate) nanoparticles for a lateral flow assay detecting IgM autoantibodies in rheumatoid arthritis T2 - Analytical biochemistry Y1 - 2021 U6 - https://doi.org/10.1016/journal.ppat.1010118 SN - 1096-0309 VL - Vol. 633 ER - TY - GEN A1 - Ehrling, Sebastian A1 - Senkovska, Irena A1 - Efimova, Anastasia A1 - Bon, Volodymyr A1 - Abylgazina, Leila A1 - Petkov, Petko A1 - Evans, Jack D. A1 - Attallah, Ahmed Gamal A1 - Wharmby, Michael Thomas A1 - Roslova, Maria A1 - Huang, Zhehao A1 - Tanaka, Hideki A1 - Wagner, Andreas A1 - Schmidt, Peer A1 - Kaskel, Stefan T1 - Temperature Driven Transformation of the Flexible Metal-Organic Framework DUT-8(Ni) T2 - Chemistry - a European journal N2 - DUT-8(Ni) metal-organic framework belongs to the family of flexible pillared layer materials. The desolvated framework can be obtained in the open pore form (op) or in the closed pore form (cp), depending on the crystal size regime. In the present work, we report on the behaviour of desolvated DUT-8(Ni) at elevated temperatures. For both, op and cp variants, heating causes a structural transition, leading to an new, crystalline compound, containing two interpenetrated networks. The state of the framework before transition (op vs. cp) influences the transition temperature: the small particles of the op phase transform at significantly lower temperature in comparison to the macroparticles of the cp phase, transforming close to the decomposition temperature. The new compound, confined closed pore phase (ccp), was characterized by powder X-ray diffraction and spectroscopic techniques, such as IR, EXAFS, and positron annihilation lifetime spectroscopy (PALS). Thermal effects of structural cp to ccp transitions were studied using differential scanning calorimetry (DSC), showing an overall exothermic effect of the process, involving bond breaking and reformation. Theoretical calculations reveal the energetics, driving the observed temperature induced phase transition. KW - Metal organic framework (MOF) KW - Thermal analysis KW - Crystal structure KW - Phase transition Y1 - 2022 UR - https://chemistry-europe.onlinelibrary.wiley.com/doi/10.1002/chem.202201281 U6 - https://doi.org/10.1002/chem.202201281 SN - 1521-3765 VL - 28 IS - 55 SP - 1 EP - 10 ER - TY - GEN A1 - Pozarowska, Emilia A1 - Pleines, Linus A1 - Prieto, Mauricio J. A1 - Tănase, Liviu Christian A1 - Souza Caldas, Lucas de A1 - Tiwari, Aarti A1 - Schmidt, Thomas A1 - Falta, Jens A1 - Morales, Carlos A1 - Flege, Jan Ingo T1 - The relation between structure sensitivity and doping of ceria(111) vs. ceria(100) T2 - Verhandlungen der DPG N2 - CeOx-Cu inverse catalysts have been shown to convert CO2 into valuable chemicals through catalytic hydrogenation. The catalytic activity may further be enhanced by alloying ceria with trivalent, catalytically active metals, such as Sm, promoting the formation of Ce3+ active sites. In this work, the structural and chemical properties of (111)- and (100)- oriented CeOx islands alloyed with samarium were explored by low-energy electron microscopy and X-ray photoemission electron microscopy. After Sm deposition on the as-grown CeOx islands, the near-surface region of (100)-oriented CeOx is reduced after exposure to H2 at 470 ∘C, whereas the deeper layers as well as the whole (111)-oriented islands retain the Ce4+ state. Subsequent reoxidation with O2 leads to the complete Ce4+ state recovery, suggesting the healing of oxygen vacancies. Additional annealing at 470 ∘C induces samarium diffusion into the ceria matrix. Yet, subsequent exposure to H2 reduces neither the (111)- nor the (100)-oriented CeSmOx islands, suggesting a quite unexpected stability of this system. KW - catalytic hydrogenation KW - Samarium alloying of cerium oxide KW - low-energy electron microscopy (LEEM) KW - X-ray photoemission electron microscopy (PEEM) KW - healing of oxygen vacancies Y1 - 2022 UR - https://www.dpg-verhandlungen.de/year/2022/conference/regensburg/part/o/session/52/contribution/11 SN - 0420-0195 PB - Deutsche Physikalische Gesellschaft CY - Bad Honnef ER - TY - GEN A1 - Böhler, Stefan A1 - Rosencrantz, Sophia A1 - Wolf, Karina A1 - Heinemann, Robert A1 - Schmidt, Peer A1 - Ganster, Johannes A1 - Büsse, Thomas A1 - Balko, Jens A1 - Rosencrantz, Ruben R. T1 - Active protease formulation in commodity polymers withstands melt processing into compounds and blown films T2 - Materials Today Communications N2 - Integrating enzymes into thermoplastic polymers is challenging due to their lack of robustness with respect to temperature and shear fields during conventional melt processing. In the present study, blown films from low-density polyethylene (LDPE) were prepared containing a technical protease from Bacillus sp. First, LDPE/protease compounds were produced followed by blown film extrusion, both processes at melt mass temperatures of 130 °C or higher. Enzyme activity was proven, both for the LDPE/protease compound and the blown film. The highest enzyme activity in the compound was determined for processing at 132 °C and a screw speed of 75 rpm. The influence of melt temperature and shear fields was studied in detail. Enzyme activities were determined for melt temperatures up to 160 °C and for screw speeds ranging from 75 to 300 rpm during compounding by twin-screw extrusion. The process was also applied for biobased and biodegradable polyesters, where similar protease activity after compounding was verified. Electron microscopy, X-ray diffraction, nuclear magnetic resonance spectroscopy and differential scanning calorimetry served to analyze components and morphology of the enzyme formulation used here. It is proposed that the porous morphology of the protease particles is beneficial for the enzyme to remain active after processing. Additionally, the polymer matrix surrounding the particles protects the protease at elevated temperatures, which can be attributed to thermal insulation. Thus, the right combination of a suited technical enzyme formulation with appropriate mild melt compounding conditions allows enzymes to be incorporated into thermoplastics and retain their activity. This opens the way to use the abundant biological functions of enzymes in thermoplastic applications. KW - Thermal analysis KW - X-ray diffraction KW - Crystal structure Y1 - 2023 UR - https://www.sciencedirect.com/science/article/pii/S2352492822018591 U6 - https://doi.org/10.1016/j.mtcomm.2022.105018 SN - 2352-4928 VL - 34 SP - 1 EP - 9 ER - TY - GEN A1 - Pożarowska, Emilia A1 - Pleines, Linus A1 - Ewert, Moritz A1 - Prieto, Mauricio J. A1 - Tănase, Liviu Christian A1 - Souza Caldas, Lucas de A1 - Tiwari, Aarti A1 - Schmidt, Thomas A1 - Falta, Jens A1 - Krasovskii, Eugene A1 - Morales, Carlos A1 - Flege, Jan Ingo T1 - Preparation and stability of the hexagonal phase of samarium oxide on Ru(0001) T2 - Ultramicroscopy N2 - We have used low-energy electron microscopy (LEEM), micro-illumination low-energy electron diffraction (µLEED) supported by ab initio calculations, and X-ray absorption spectroscopy (XAS) to investigate in-situ and in real-time the structural properties of Sm2O3 deposits grown on Ru(0001), a rare-earth metal oxide model catalyst. Our results show that samarium oxide grows in a hexagonal A-Sm2O3 phase on Ru(0001), exhibiting a (0001) oriented-top facet and (113) side facets. Upon annealing, a structural transition from the hexagonal to cubic phase occurs, in which the Sm cations exhibit the +3 oxidation state. The unexpected initial growth in the A-Sm2O3 hexagonal phase and its gradual transition to a mixture with cubic C-Sm2O3 showcases the complexity of the system and the critical role of the substrate in the stabilization of the hexagonal phase, which was previously reported only at high pressures and temperatures for bulk samaria. Besides, these results highlight the potential interactions that Sm could have with other catalytic compounds with respect to the here gathered insights on the preparation conditions and the specific compounds with which it interacts. KW - Samarium oxide (Sm2O3) KW - low-energy electron microscopy (LEEM) KW - X-ray photoemission electron microscopy (XPEEM) KW - Facets KW - Epitaxy KW - Hexagonal phase Y1 - 2023 U6 - https://doi.org/10.1016/j.ultramic.2023.113755 SN - 0304-3991 SN - 1879-2723 VL - 250 ER -