TY - CHAP A1 - Richter, Matthias A1 - Städter, Matthias A1 - Paloumpa, Ioanna A1 - Schmeißer, Dieter T1 - Multiple Auger Decay at resonant photo-excitation in carbon thin films T2 - Verhandlungen der Deutschen Physikalischen Gesellschaft N2 - We use resonant photoemission at the C1s edge to study the electronic structure of HOPG, graphene flakes and monolayer graphene. We find remarkable differences in the profile of the Auger decay channels, which we attribute to an additional multiple-Auger with a three-hole final state. A prerequisite for the appearance of this decay mechanism is the existence of localized excitonic states, which cause the appearance of the multiple Auger decay. Defects (pits, holes, steps and kinks) can act as localized excitonic states. We use those effects to identify the existence and the quantity of such defect states within the pi*-band regime in carbon thin films, because the intensity of the three-hole Auger decay is varying with the defect density of the carbon films. The defect-excitonic states can be either localized in the band-gap at the M-point or in case of surface defects like steps, kinks or pits even at the K-point by losing the pure sp2 character of the films. We find that the appearance of the multiple Auger decay is different for multilayer and monolayer graphene. In particular the interaction of impurities leads to broadening of the C1s core levels. The three-hole Auger decay spectroscopy is a new method to detect such contaminations with a high sensitivity. KW - resonant photoelectron spectroscopy KW - Auger decay KW - multiple decay KW - carbon thin films Y1 - 2013 UR - http://www.dpg-verhandlungen.de/year/2013/conference/regensburg/part/hl/session/52/contribution/6?lang=de PB - Deutsche Physikalische Gesellschaft CY - Bad Honnef ER - TY - CHAP A1 - Richter, Matthias A1 - Schmeißer, Dieter T1 - The Co2p spin and oxidation state in Co-PI catalysts T2 - Verhandlungen der Deutschen Physikalischen Gesellschaft N2 - The electronic structure of cobalt based catalysts used for photocatalytic water splitting in solar cells is analyzed using synchrotron radiation photoelectron spectroscopy. The catalyst films are prepared by electrochemical deposition. We employ a X-ray photoelectron spectroscopy study to analyze the Co2p and O1s core levels, absorption edges and valence bands. We discuss our resonant data in terms of the partial density of states of the valence and conduction band. We find a difference in the Co oxidation state as a function of film thickness (deposited charge). From the relative amount of Co, O, K and P we favor the molecular cobaltate cluster-like structure as the structural motif of the Co-PI catalyst. Further, at resonant PES at the Co2p edge we find the Co2p partial DOS to exhibit no sharp features next to the VBM, instead there is a broad emission at around 6eV below EFerrmi. The former are found in LiCoO2 and other Co-oxide systems with a Co3+ ground state. We attribute such sharp features to the low spin (LS) configuration of Co3+ and deduce that in the Co catalysts there is no evidence for the corresponding LS contributions. Our data prove the Co2+ ground state and demonstrate that it is exclusively in the Co3d7 high spin state in the pristine catalyst films. KW - X-Ray photoelectron spectroscopy KW - resonant photoemission spectroscopy KW - cobalt based catalyst KW - water splitting Y1 - 2013 UR - http://www.dpg-verhandlungen.de/year/2013/conference/regensburg/part/ds/session/35/contribution/9?lang=de PB - Deutsche Physikalische Gesellschaft CY - Bad Honnef ER - TY - CHAP A1 - Städter, Matthias A1 - Richter, Matthias A1 - Schmeißer, Dieter T1 - Fano-Profiles in HOPG and graphene flakes T2 - Verhandlungen der Deutschen Physikalischen Gesellschaft N2 - We investigated the electronic structure of the valence and conduction band of HOPG by 2D resonant photoemission spectroscopy. Our aim is to understand the electronic structure of defects and inhomogeneities in graphene and related materials in more detail. From our measurements we find that the transition from the sigma-band to the pi*-band at the M-point shows a characteristic Fano-Profile. A Fano-Profile occurs as the result of the interference of the band to band transition and a parallel transition to a discrete energy level within the band gap. The theory of Fano enables us to determine the energetic location of these discrete level. It is found to be several meV above the Fermi-Energy. Additional measurements on graphene flakes lead to similar results for the sigma- to pi*-band transition and the location of the discrete energy state. With this we not only can determine the energetic states of defects but also get a better understanding of the origin of the Fano profile which is a particular detail of the resonant absorption process. KW - resonant photoelectron spectroscopy KW - Fano profiles KW - Graphene KW - HOPG Y1 - 2013 UR - http://www.dpg-verhandlungen.de/year/2013/conference/regensburg/part/hl/session/52/contribution/5?lang=de PB - Deutsche Physikalische Gesellschaft CY - Bad Honnef ER - TY - CHAP A1 - Fischer, Christian B. A1 - Rohrbeck, Magdalena A1 - Wehner, Stefan A1 - Richter, Matthias A1 - Städter, Matthias A1 - Schmeißer, Dieter T1 - Interlayer formation of Diamond-Like Carbon Coatings on Polyethylene Plastic Material T2 - Verhandlungen der Deutschen Physikalischen Gesellschaft N2 - The coating of materials with diamond-like carbon (DLC) is a very common way to further improve and modify surface specific properties. Although DLC is frequently used as a protective coating on several substrates, the chemical and physical properties throughout the coating process on plastics are yet sparsely investigated. Different layer thicknesses of two types of protective coatings one sp3-enriched (robust, r-type) and one with more sp2-centers (flexible, f-type) have been realized on polyethylene by PECVD. Microscopic analysis showed diverse surface topographies for the two DLC-types. NEXAFS spectroscopy revealed significant details of carbon centers in chemically different neighborhood displaying a characteristic fingerprint behavior. The appropriate explanation for the current carbon deposition process is obviously the formation of an interlayer between these unequal materials. An improved understanding of hard DLC and soft polyethylene assembly is part of the present work. KW - Diamond-like carbon (DLC) KW - topography KW - X-ray absorption spectroscopy KW - plasma enhanced chemical vapor deposition Y1 - 2013 UR - http://www.dpg-verhandlungen.de/year/2013/conference/regensburg/part/o/session/33/contribution/4?lang=de PB - Deutsche Physikalische Gesellschaft CY - Bad Honnef ER - TY - CHAP A1 - Goriachko, Andrii A1 - Müller, Klaus A1 - Paloumpa, Ioanna A1 - Schmeißer, Dieter T1 - Scanning Kelvin Probe Microscopy Investigations of Au-P3HT-Au structures for Organic Field Effect Transistors T2 - Verhandlungen der Deutschen Physikalischen Gesellschaft N2 - We report on the scanning Kelvin probe microscopy (SKPM) investigation of the source-channel-drain structures of organic field effect transistor (OFET). A poly-3-hexyl-thiophen (P3HT) organic semiconductor film, spin-coated on a glass-substrate and 65 nm thick, is used as a 2 mkm channel between Au source (drain) electrodes. Depending on the preparation conditions, the P3HT film consists of either amorphous nm-seized molecular clsuters or mkm-long chains. The SKPM allows mapping of electric potential along with the surface topography on the DC-biased structures (8V applied between source and drain). It reveals a linear potential fall in the channel region as well as the abscence of potential jumps (contact resistance) in the electrode/channel regions. This is a direct indication of the top-gate OFET type advantage, which the given structure is suited for. Due to the high spatial resolution of the UHV-based SKPM, doping inhomogenities of the p-type P3HT semiconductor as well as the space charge region on the electron injecting electrode are observed. In addition we present SKPM investigations of the structure with source and drain electrodes but without a semiconductor, showing electric field configuration for the given electrodes geometry. KW - scanning Kelvin probe microscopy (SKPM) KW - organic field effect transistor (OFET) Y1 - 2005 UR - http://www.dpg-verhandlungen.de/year/2005/conference/berlin/part/syoo/session/6/contribution/24?lan=en PB - Deutsche Physikalische Gesellschaft CY - Bad Honnef ER - TY - CHAP A1 - Hoffmann, Patrick A1 - Goryachko, Andriy A1 - Schmeißer, Dieter T1 - Growth of oxynitrides on Si-rich 4H-SiC(0001) surfaces T2 - Verhandlungen der Deutschen Physikalischen Gesellschaft N2 - Oxynitride layers are grown on 4H-SiC(0001) by a thermal treatment in N2O. The nitrogen content is controlled by varying the growth conditions (N2O pressure and substrate temperature) and the nitrogen incorporation is found to be stronger for higher substrate temperatures and lower N2O pressures. Excess carbon is generated due to SiC decomposition under such growth conditions (high temperature and low N2O pressure) which leads to unwanted high interface state density and has to be avoided. Our approach is to prepare a Si-rich or even Si-covered SiC surface by Si evaporation. Upon oxidation in N2O the additional silicon is expected to compensate the loss of silicon from the SiC while preparation. The Si-rich SiC surface as well as the grown layers were investigated by photoelectron spectroscopy (XPS) for chemical analysis and by AFM/STM for analysis of the surface morphology. Concerning the chemical analysis we focus on the total nitrogen content, on the amount of silicon nitride Si3N4 and of silicon oxynitride SiOxNy, and on the existence of sub-oxides which build the interface between SiC and the oxynitride layers. KW - X-Ray photoelectron spectroscopy KW - scanning tunneling microscopy (STM) KW - atomic force microscopy (AFM) KW - silicon oxynitride KW - 4H-SiC(0001) Y1 - 2005 UR - http://www.dpg-verhandlungen.de/year/2005/conference/berlin/part/hl/session/26/contribution/1?lan=en PB - Deutsche Physikalische Gesellschaft CY - Bad Honnef ER - TY - CHAP A1 - Sohal, Rakesh A1 - Henkel, Karsten A1 - Müller, Klaus A1 - Schmeißer, Dieter T1 - Growth and Characterization of 3C-SiC thin films on Si substrates T2 - Verhandlungen der Deutschen Physikalischen Gesellschaft N2 - This work reports on the growth and characterization of cubic silicon carbide thin films. A cold wall low pressure chemical vapour deposition (LPCVD) system has been used to grow the cubic silicon carbide. The two step method, carbonization and subsequent growth, has been used to grow good quality 3C-SiC thin films. The composition and structure of deposited thin films have been analysed by Fourier Transform Infrared Spectroscopy (FTIR), XPS and X-Ray Diffractometry (XRD). The structural quality of the films has been optimized as a function of substrate temperature during carbonization and growth. X-rays diffraction measurements shows that the grown layers are highly oriented crystalline cubic silicon carbide. KW - low pressure chemical vapor deposition (LPCVD) KW - 3C-SiC KW - X-ray photoelectron spectroscopy (XPS) KW - Fourier Transform Infrared Spectroscopy (FTIR) KW - X-Ray diffraction Y1 - 2005 UR - http://www.dpg-verhandlungen.de/year/2005/conference/berlin/part/hl/session/58/contribution/50?lan=en PB - Deutsche Physikalische Gesellschaft CY - Bad Honnef ER - TY - CHAP A1 - Goryachko, Andriy A1 - Beuckert, Guido A1 - Zaumseil, Peter A1 - Wagner, Guenter A1 - Schmeißer, Dieter T1 - Investigations of Pr2O3 growth modes on 4H-SiC(0001) Surfaces T2 - Verhandlungen der Deutschen Physikalischen Gesellschaft N2 - The SiC is suited especially well for high power and high voltage semiconductor devices. In order to increase the reliability against electrical breakdown of metal-insulator-semiconductor (MIS) structures, one needs to use the insulator with possibly higher dielectric constant. Pr2O3 is shown to posses a much higher dielectric constant (equals 30) than traditionally used SiO2. Therefore, Pr2O3/SiC is an excellent material combination for high voltage MIS devices. The 4H-SiC(0001) substrates are characterised with scanning tunneling microscopy, while the Pr2O3 surface - with atomic force microscopy technique. We show distinct growth modes of Pr2O3 film, such as 3D and layer by layer growth. The crystalline structure and film thickness are determined by X-ray diffraction and its chemical composition by X-ray photoelectron spectroscopy. The Pr2O3 film characteristics are optimised for high-quality MIS structures in terms of lateral uniformity, low interface states density and leakage current, as well as physical integrity. KW - SiC KW - Pr2O3 KW - X-ray photoelectron spectroscopy (XPS) KW - X-Ray diffraction Y1 - 2004 UR - http://www.dpg-verhandlungen.de/year/2004/conference/regensburg/part/ds/session/9/contribution/4?lang=de SN - ISSN 0420-0195 PB - Deutsche Physikalische Gesellschaft CY - Bad Honnef ER - TY - CHAP A1 - Hoffmann, Patrick A1 - Schmeißer, Dieter T1 - Growth of oxynitrides on Si-rich 4H-SiC(0001) surfaces T2 - Verhandlungen der Deutschen Physikalischen Gesellschaft N2 - It will be reported on the growth of oxynitride thin layers (≤10nm) on (0001)-oriented 4H-SiC surfaces. The oxynitride layers were grown by a thermal treatment of the samples in low pressure N2O ambient. By varying the growth conditions (N2O pressure, sample temperature, growth time) different layers were made. The grown layers were investigated by photoelectron spectroscopy (XPS) for chemical analysis and by AFM/STM for analysis of the surface morphology. Concerning the chemical analysis it will be discussed the general nitrogen content of the samples, the composition of the films (e.g. content of silicon nitride Si3N4 and silicon oxynitride SiOxNy) and the sub-oxides which build the interface between SiC and the oxynitride layers. Concerning the surface morphology mainly the roughness will be discussed. The so obtained results for oxynitride thin films on 4H-SiC will be compared to similarly prepared oxynitride layers on Si(111) investigated in the past. KW - oxynitride KW - 4H-SiC KW - X-ray photoelectron spectroscopy (XPS) KW - Atomic foce microscopy (AFM) KW - scanning tunneling microscopy (STM) Y1 - 2004 UR - http://www.dpg-verhandlungen.de/year/2004/conference/regensburg/part/hl/session/40/contribution/4?lang=de PB - Deutsche Physikalische Gesellschaft CY - Bad Honnef ER - TY - CHAP A1 - Müller, Klaus A1 - Burkov, Yevgen A1 - Schmeißer, Dieter T1 - Spectromicroscopic Characterisation of All Polymer Transistor Structures T2 - Verhandlungen der Deutschen Physikalischen Gesellschaft N2 - In order to optimize organic field effect transistors, the characterization of surfaces in terms of their roughness or chemical composition is very important. We report on high resolution spectromicroscopic mapping of organic thin film transistors by photoemission electron microscopy (PEEM). It was shown that PEEM is a useful technique to characterize the surface morphology (roughness), the chemical homogeneity or the composition of structures in between the source and drain electrodes. Mapping of surface potentials, especially at the interface electrode/channel is possible. We compare different preparation methods and the characterization at applied voltages is also shown. The transistors itself were prepared by a new low cost method. The electrodes for source and drain have been prepared by a plotting method with colloidal graphite or carbon black as the conducting material. P3HT was used as active layer and has been prepared by spin coating. KW - organic field effect transistor KW - photoemission electron microscopy (PEEM) Y1 - 2004 UR - http://www.dpg-verhandlungen.de/year/2004/conference/regensburg/part/syoh/session/5/contribution/74?lang=de PB - Deutsche Physikalische Gesellschaft CY - Bad Honnef ER - TY - CHAP A1 - Müller, Klaus A1 - Paloumpa, Ioanna A1 - Schwiertz, Carola A1 - Jahnke, Agnes A1 - Schmeißer, Dieter T1 - All Polymer Field-Effect-Transistors based on Low-Cost-Microstructuring T2 - Verhandlungen der Deutschen Physikalischen Gesellschaft N2 - Thin film transistors with P3HT as active layer have been prepared by spin coating. The electrodes for source and drain have been prepared by a low cost plotting method with colloidal graphite or carbon black as the conducting material. PEDOT or carbon black was used as gate electrode. The devices, prepared by different methods and materials have been characterized by electrical measurements, for example, their transfer and output characteristics. Furthermore, the influence of different materials on effects like hysteresis or reproducibility will be compared. In addition, we describe a project investigating new types of biosensors with functionalized gate electrodes. Exchanges of dipole moments or charges by immobilisation of biomolecules will change the electrical characteristic of the transistor, which leads to a sensing signal proportional to their amount. KW - organic field effect transistor KW - low cost printing KW - microstructuring Y1 - 2004 UR - http://www.dpg-verhandlungen.de/year/2004/conference/regensburg/part/syoh/session/5/contribution/75?lang=de PB - Deutsche Physikalische Gesellschaft CY - Bad Honnef ER - TY - CHAP A1 - Torche, Mohamed A1 - Müller, Klaus A1 - Henkel, Karsten A1 - Lupina, Grzegorz A1 - Goryako, Andrey A1 - Wollweber, Jürgen A1 - Schmeißer, Dieter T1 - Investigations of 3C-SiC growth on Si (001) T2 - Verhandlungen der Deutschen Physikalischen Gesellschaft N2 - Carbide was grown on Si (001) - substrates with supply of C2H2. Investigation of the interface Si/SiC (buffer layer) is essential for optimized preparation conditions, leading to a high quality of the growing SiC crystal. In addition to the lattice mismatch of 20 per cent between Si and SiC, which causes defects like dislocations or stacking faults, the chemical homogeneity of this layer is important. XPS was used to characterize the first state of SiC crystal growth on the Si substrate. Carbonizing with C2H2 leads to surface reactions which build up the buffer layer. By using electron spectroscopy, it was possible to characterize the SiC/Si (001) buffer layer, depending on the following reaction parameters: Tsubstrate , PC2H2 , PH2 , the ratio of pressures and the reaction time. The measurements were performed in terms of the content of carbide, oxide and roughness/etching-efficiency (Profilometer) for the reaction parameters above. We found, that the most critical parameter is the temperature of the substrate (Tsubstrate). KW - 3C-SiC KW - chemical vapor deposition (CVD) KW - X-ray photoelectron spectroscopy (XPS) Y1 - 2004 UR - http://www.dpg-verhandlungen.de/year/2004/conference/regensburg/part/hl/session/44/contribution/42?lang=de PB - Deutsche Physikalische Gesellschaft CY - Bad Honnef ER - TY - CHAP A1 - Schmeißer, Dieter A1 - Müssig, Hans-Joachim T1 - Stability and electronic properties of silicates in the system SiO2 - Pr2O3 - Si(001) T2 - Verhandlungen der Deutschen Physikalischen Gesellschaft N2 - Hetero- oxides are the candidates to replace SiO2 as the gate dielectric material for sub-0.1µm CMOS technology. In particular, the basic interaction mechanisms at the interface are a key issue and a solid knowledge of these mechanisms is required to address reliability issues. The challenge in material science is to understand the chemical bonding of the hetero oxides and Si on a microscopic scale. This report focuses on the interaction of the high dielectric constant (DK) material Pr2O3 with SiO2 and the bare Si(001) surface. Photoelectron spectroscopy (PES) using tunable Synchrotron radiation (undulator U49/2 at BESSY II) is shown to provide spectroscopic information which is used for characterization of the electronic structure elements at the interface as well as for a non-destructive depth profiling. The chemical state of the Si atoms at the interface is identified and the chemical stability of the various oxide phases is discussed. We determine the variation of the elemental composition across the interface and follow the stability of the silicate phase. KW - Pr2O3 KW - high-k KW - X-ray photoelectron spectroscopy (XPS) KW - silicate Y1 - 2004 UR - http://www.dpg-verhandlungen.de/year/2004/conference/regensburg/part/hl/session/31/contribution/3?lang=de PB - Deutsche Physikalische Gesellschaft CY - Bad Honnef ER - TY - CHAP A1 - Hoffmann, Patrick A1 - Schmeißer, Dieter T1 - Depth Profiling of Ultrathin Oxynitride Layers Using Synchrotron Radiation T2 - Verhandlungen der Deutschen Physikalischen Gesellschaft N2 - To determine the depth structure of samples various destructive (SIMS, depth profiling with sputtering and AES or XPS) and non-destructive techniques (RBS - Rutherford-Back-Scattering) are available. But all methods are less suitable for investigating especially ultrathin (<5nm) layers: While the destructive techniques suffer from Ion-mixing the RBS can not deliver chemical information. Due to the depth-dependent attenuation of photo-electrons XPS also contains depth information. As XPS gives only a sum signal across the layer one needs to modify the Inelastic Mean Free Path (IMFP) of the photo-electrons to vary the depth information in the photo-electron spectra. This can be done by changing the kinetic energy with the use of different excitation energies delivered from a Synchrotron. Using this method we were able to investigate the chemical depth structure of silicon oxynitride layers. The layers were grown on Si(111) by a N2O-treatment. The depth profile of that layer shows a silicon nitride layer forming the interface between the silicon substrate and the oxynitride. KW - oxynitride KW - X-ray photoelectron spectroscopy KW - depth profiling Y1 - 2003 UR - http://www.dpg-verhandlungen.de/year/2003/conference/dresden/part/o/session/12/contribution/36?lang=de PB - Deutsche Physikalische Gesellschaft CY - Bad Honnef ER - TY - CHAP A1 - Müller, Klaus A1 - Schmeißer, Dieter T1 - Elektronenspektroskopie an Kupferindiumdisulfid Oberflächen T2 - Verhandlungen der Deutschen Physikalischen Gesellschaft N2 - In diesem Beitrag wird eine Studie vorgestellt, welche die elektronenspektroskopische Untersuchung von CIS-Oberflächen für Solarzellen zum Thema hatte. XPS-UPS Analysen von Cu-reichen CuInS2-Dünnfilmen zeigten, daß die Variationen der Elementverhältnisse im Verlauf eines kontrollierten Heizprozesses entlang binärer Schnitte des ternären Phasendiagramms Cu-In-S verlaufen. Die Elementverhältnisse bei zusätzlich aufgedampftem Kupfer und erhöhter Temperatur föhrten in den Homgenitätsbereich von CuInS2. PEEM-Untersuchungen zur Probenmorphologie zeigten, daß ein Sinterprozess während der Temperung der Proben bis 550 C und einer Belegung mit Kupfer erfolgt. Mit Differenz-PEEM-Aufnahmen konnten kupferreiche Fremdphasen wie CuS an der Oberfläche sichtbar gemacht werden. Die in-situ Charakterisierung des Oberflächenchemismus im Verlauf der Temperung zeigte eine zunehmende Homgenität der Elementverteilung, was auf einen geringer werdenden Anteil von Fremdphasen hindeutet. NEXAFS-Aufnahmen ergaben erstmals Informationen über die Bandstruktur oberhalb der Fermienergie und ebenfalls Hinweise auf Fremdphasen sowie deren Reaktionen bei höheren Temperaturen. KW - CIS-Solarzellen KW - Röntgen-Absorptionsspektroskopie KW - Photoemissionselektronenmikroskopie Y1 - 2003 UR - http://www.dpg-verhandlungen.de/year/2003/conference/dresden/part/hl/session/14/contribution/98?lang=de PB - Deutsche Physikalische Gesellschaft CY - Bad Honnef ER - TY - CHAP A1 - Styervoyedov, Andriy A1 - Paloumpa, Ioanna A1 - Schmeißer, Dieter T1 - Composition and thermal stability of thin functional oxidic (Pr, La, Y) and metallic (Ru, Ti) layers on Si and SiC substrates T2 - Verhandlungen der Deutschen Physikalischen Gesellschaft N2 - Thin Pr-, La- and Y- based oxide layers for applications as gate dielectric in metal-oxide-semiconductor (MOS) structures are investigated with x-ray photoelectron spectroscopy. The films with a thickness of around 2nm have been prepared on Si and SiC wafers by various chemical deposition methods based on nitrate solutions. In addition, we report on Ti- and Ru- based metal contacts prepared in the same way. The film composition is analysed and annealing steps in vacuum up to 900∘C have been applied to test their thermal stability. The interface characteristics, surface composition and thermal stability of MOS functional multilayers have been studied and will be presented. KW - Pr-, La- and Y- based oxides KW - MOS transistor KW - high-k KW - X-Ray photoelectron spectroscopy Y1 - 2005 UR - http://www.dpg-verhandlungen.de/year/2005/conference/berlin/part/ds/session/24/contribution/17?lan=en PB - Deutsche Physikalische Gesellschaft CY - Bad Honnef ER - TY - CHAP A1 - Schmeißer, Dieter T1 - The initial interaction of Pr2O3 to (001) and (111) oriented Si substrates T2 - Verhandlungen der Deutschen Physikalischen Gesellschaft N2 - The high surface sensitivity of synchrotron based core level spectroscopy is employed to study the initial growth of Pr2O3 on Si(001) and Si(111) substrates. The Si2p core levels are different for the two substrates when the exposure is below 1nm. The core level shifts indicate a single bonding of the oxide on the terminal Si atom in Si(111) while on Si(001) the two dangling bonds are reactive. On both surfaces a significant broadening in the substrate emission is found and interpreted in terms of non bonding Si atoms located at the interface. Upon increasing the Pr2O3 exposure above 1nm the Si back bonds in the first Si layer are attacked to form Si - O - Pr bonds which cause a silicate like core level shift. KW - Pr2O3 KW - high-k KW - X-ray photoelectron spectroscopy (XPS) Y1 - 2005 UR - http://www.dpg-verhandlungen.de/year/2005/conference/berlin/part/ds/session/11/contribution/2?lan=en PB - Deutsche Physikalische Gesellschaft CY - Bad Honnef ER - TY - CHAP A1 - Lupina, Grzegorz A1 - Schroeder, Thomas A1 - Dabrowski, Jarek Marek A1 - Schmeißer, Dieter A1 - Müssig, Hans-Joachim T1 - Ti-doping of Pr silicate layers for high-k dielectrics applications T2 - Verhandlungen der Deutschen Physikalischen Gesellschaft N2 - Near-term downscaling of the metal-oxide-semiconductor field-effect transistors (MOSFETs) requires the replacement of the SiO2 gate oxide with a material having a higher dielectric constant. Recent studies indicate that silicate materials are the most promising candidates; among them are Pr silicates. Applying a combination of x-ray photoelectron spectroscopy (XPS), electrical measurements (C-V), and ab initio calculations, we investigated the effect of thin Ti doping on the structural and electrical properties of the gate stacks composed of a Pr silicate film and a SiO2-based interfacial buffer layer. Metallic Ti was deposited at room temperature after the formation of the Pr silicate dielectric. The resulting layered structures were annealed under ultra-high vacuum (UHV) at various temperatures between 70∘C and 880∘C. XPS indicates that the evaporated layer preserves its metallic character over the whole range of UHV annealing temperatures. Synchrotron radiation XPS at BESSY II shows that large amounts of Ti atoms incorporated into the Pr silicate remain metallic even after air exposure at room temperature. Annealing in nitrogen ambient at 300∘C leads to the oxidation of these atoms so that a mixed Pr:Ti silicate is formed. We show that the so formed dielectrics exhibit an improved equivalent oxide thickness and a reduced density of interface states. KW - high-k KW - X-ray photoelectron spectroscopy KW - ab inito calculations KW - Capacitance-voltage measurements KW - Pr silicate Y1 - 2005 UR - http://www.dpg-verhandlungen.de/year/2005/conference/berlin/part/df/session/6/contribution/5?lan=en PB - Deutsche Physikalische Gesellschaft CY - Bad Honnef ER - TY - CHAP A1 - Henkel, Karsten A1 - Paloumpa, Ioanna A1 - Müller, Klaus A1 - Schmeißer, Dieter T1 - P(VDF/TrFE) as a ferroelectric dielectric for Organic Field effect Transistors in MFIS structure T2 - Verhandlungen der Deutschen Physikalischen Gesellschaft N2 - MFIS structures consisting of metal, ferroelectric poly[vinylidene fluoride trifluoroethylene](P[VDF/TrFE]), insulator, semiconductor (Si) are fabricated and the influence of the polarization of the P(VDF/TrFE) on the CV characteristics of these structures is investigated. We find a characteristic ferroelectric hysteresis in the CV curves upon increasing the voltage scan window (e.g.-U...U,U=6...30V, |UP(VDF/TrFE)|≤15V, dP(VDF/TrFE)=300 nm). A writing process with adequate electric fields causes large shifts in the flatband voltage ( Δ UFB>4V for the quoted example before) which are stable over days. We report on our investigations which focus on the switching behavior by varying the parameters like polymer thickness, writing field strength and time, long time stability, reversing voltage and insulating material (SiO2, PMMA (Polymethylmetacrylate)). This material combination is favorable for transfer into our full organic concept of field effect transistors for application as a nondestructive readout memory (NDRO) cell. KW - P(VDF/TrFE) KW - Organic ferroelectric field effect transistor KW - capacitance voltage measurements Y1 - 2005 UR - http://www.dpg-verhandlungen.de/year/2005/conference/berlin/part/syoo/session/6/contribution/39?lan=en PB - Deutsche Physikalische Gesellschaft CY - Bad Honnef ER - TY - CHAP A1 - Müller, Klaus A1 - Burkov, Yevgen A1 - Schmeißer, Dieter T1 - Surface potential profiling on organic thin film transistors by photoemission-electron-microscopy (PEEM) T2 - Verhandlungen der Deutschen Physikalischen Gesellschaft N2 - Surface potential imaging with Photoemission-electron-microskopy (PEEM) in high lateral resolution is introduced as a new tool for the characterisation of organic transistor structures. We use source-drain- electrode structures of different organic materials like carbon-black or graphite plotted on a printing foil. Semiconducting regioregular Poly(3-Hexylthiophene-2,5-diyl) (P3HT) was deposited by spin coating. For our measurements we used radiation of a standard high pressure Hg-lamp (4,9 eV) and synchrotron radiation at the BESSYII-U49/2 beam line. In contrast to Kelvin-AFM measurements of the surface potential, PEEM enables a simultaneous analysis of chemical composition by photoelectron spectroscopy. UPS, for example, at zero potential gives information on chemical homogeneity of the organic semiconductor in lateral resolution. PEEM images at applied voltages, compared with UPS-spectra, gives informations on doping profiles in the semiconductor, for example. In conclusion, PEEM should be a complementary method for characterisation of the surface potential with Kelvin-AFM. In addition, PEEM gives opportunities for measurements of chemical composition in the working state of the transistor (applied voltages). KW - organic field effect transistor KW - Photoemission-electron-microscopy (PEEM) KW - Kelvin-AFM KW - X-Ray photoelectron spectroscopy Y1 - 2005 UR - http://www.dpg-verhandlungen.de/year/2005/conference/berlin/part/syoo/session/6/contribution/41?lan=en PB - Deutsche Physikalische Gesellschaft CY - Bad Honnef ER - TY - CHAP A1 - Müller, Klaus A1 - Paloumpa, Ioanna A1 - Henkel, Karsten A1 - Schmeißer, Dieter T1 - Organic Field Effect Transistors with polymer high-k dielectric insulator T2 - Verhandlungen der Deutschen Physikalischen Gesellschaft N2 - Organic field effect transistors consisting of the copolymer poly(vinylidene fluoridetrifluoroethylene) (P(VDF-TrFE)) and P3HT (poly(3-hexlythiophene)) as active layer have been fabricated. The influence of P(VDF-TrFE) on the transconductance of organic field effect transistors was investigated and enhanced gate effects are observed compared to similar transistors with PMMA (Polymethylmetacrylate) as gate dielectric. Due to the high dielectric constant of P(VDF-TrFE) (DK=12) an operation voltage smaller than for a conventional organic dielectric like PMMA (DK=3.3) was observed. The thickness of the spincoated dielectric layers is in the range of 2microns and in consequence, no significant hysteresis was found, a prerequisite for transistor operation. KW - organic field effect transistor KW - P(VDF/TrFE) KW - high-k organic Y1 - 2005 UR - http://www.dpg-verhandlungen.de/year/2005/conference/berlin/part/syoo/session/6/contribution/30?lan=en PB - Deutsche Physikalische Gesellschaft CY - Bad Honnef ER - TY - CHAP A1 - Geuss, Markus A1 - Müller, Klaus A1 - Paloumpa, Ioanna A1 - Schmeißer, Dieter T1 - Surface Potential profiling on operating full organic thin film transistors by Kelvin probe force microscopy T2 - Verhandlungen der Deutschen Physikalischen Gesellschaft N2 - Kelvin-AFM is employed to study all polymer organic thin film transistors which are promising candidates for low cost - low performance applications like active matrix displays, sensors or single-serving devices. We use bottom contact source-drain- electrode structures of different organic materials like carbon-black or graphite plotted on a printing foil. Semiconducting regioregular Poly(3-Hexylthiophene-2,5-diyl) (P3HT) was subsequently deposited by spin coating. Surface potential profiles across the transistor channel were measured by Kelvin-AFM for various source-drain potential differences and signs. We found that contact resistances cause characteristic steps in the surface potential near the channel edges which vary with the electrode material. Furthermore, nonlinearities appear in the potential gradient which possibly give evidence for lateral inhomogeneities of the carrier mobilities. In summary, surface potential imaging with high lateral resolution ( approx. 100 nm) is introduced as a powerful tool for the characterisation of the transistor performance and the selection of suitable low cost electrode materials. KW - organic field effect transistor KW - Kelvin probe force microscopy Y1 - 2005 UR - http://www.dpg-verhandlungen.de/year/2005/conference/berlin/part/syoo/session/6/contribution/36?lan=en PB - Deutsche Physikalische Gesellschaft CY - Bad Honnef ER - TY - CHAP A1 - Torche, Mohamed A1 - Schmeißer, Dieter T1 - The interaction of Al, Au, Ag, and Ti metal contacts with Pr2O3 thin films T2 - Verhandlungen der Deutschen Physikalischen Gesellschaft N2 - Pr2O3 is one of the promising high-k oxides desirable to replace SiO2 for the sub-100nm field-effect transistors (FETs) and dynamic random access memory (DRAM) capacitors. Here we focus on the metallic contacts used for the MOS and MIM based structures. With the thickness of Pr2O3 being around 3nm the metal interaction is crucial to avoid a reduction of the dielectric properties by metal percolation, crack filling or diffusion processes. We use XPS and SRPS to study the initial interaction as well as the thermal stability of metals (Al, Ag, Au, and Ti) on Pr2O3 films. We show that Al, Ag, Au form initial metallic layer which react already at temperatures around 300∘C. In contrast, Ti is found to be more stable than the other metals. We determine the formation of Ti-oxides at the Ti / Pr2O3 interface and its thermal stability. Ti is found to build a good diffusion barrier between the oxide and the metal. KW - high-k KW - Pr2O3 KW - X-ray photoelectron spectroscopy (XPS) KW - Al, Ag, Au, and Ti electrodes KW - metal dielectric interaction Y1 - 2005 UR - http://www.dpg-verhandlungen.de/year/2005/conference/berlin/part/ds/session/11/contribution/4?lan=en PB - Deutsche Physikalische Gesellschaft CY - Bad Honnef ER - TY - CHAP A1 - Seifarth, Olaf A1 - Burkov, Yevgen A1 - Schmeißer, Dieter A1 - Sydorenko, Alexander A1 - Krenek, Radim A1 - Stamm, Manfred T1 - Photoelectron spectroscopy and microscopy on magnetic nano particles embedded into block copolymers T2 - Verhandlungen der Deutschen Physikalischen Gesellschaft N2 - The formation of metallic nano particles stored in thin films of block copolymers has been investigated by means of synchrotron radiation based photoemission spectroscopy (PES) and microscopy (PEEM). Empty channels in poly(styrene-block-4-vinylpyridine) copolymer with diameters of tens of nanometers filled with CrO2, Cr2O3 and Ni provide ideal bases for performing electron spectroscopy with energy and lateral resolution on magnetic nano particles. We present UPS, XPS, NEXAFS spectra and PEEM images on and off the C 1s, Cr 2p, Ni 2p resonances and discuss the geometric and electronic structure of such compounds. The synchrotron radiation was delivered from the U49/2 beamline at BESSY II. KW - photoelectron emission microscopy (PEEM) KW - X-ray photoelectron spectroscopy KW - X-ray absorption spectroscopy KW - block copolymers KW - magnetic nano particles Y1 - 2005 UR - http://www.dpg-verhandlungen.de/year/2005/conference/berlin/part/cpp/session/29/contribution/27?lan=en PB - Deutsche Physikalische Gesellschaft CY - Bad Honnef ER - TY - CHAP A1 - Mikalo, Ricardo Pablo A1 - Appel, Günter A1 - Hoffmann, Patrick A1 - Schmeißer, Dieter T1 - Conducting Polypyrrole doped with Phthalocyaninesulfonates - new materials for chemical sensors T2 - Verhandlungen der Deutschen Physikalischen Gesellschaft N2 - Polypyrrole - a conducting polymer - is used as an active electrode of a quartz micro ballance and considered as a gate electrode in all-polymer field effect transistors used as chemical sensor. We use substituted phthalocyanines as dopants of polypyrrole as they offer the possibility to enhance the dopant concentration as well as to include functionalized groups. We studied these films by photoelectron spectroscopy, NEXAFS, PEEM, and TEM. These investigations revealed that the electronic structure as well as the morphology are highly dependent on the dopant’s structure. We suggest a new charge transport model for 5-ring heterocycle conductive polymers. Whereas in the standard model only the carbon backbone is considered for the charge transport, we found by NEXAFS investigations that the heteroatom has a considerable high participation in the gap states, which are responsible for the charge transport. The dopants π-interactions force the nitrogen lone pair wave functions to contribute to the conducting polymer π-system. This is a novel approach concerning the application as chemical sensors since the reversible interaction of the analyte modifies the dopant and not the matrix. KW - polypyrrole KW - conducting polymer KW - X-ray photoelectron spectroscopy (XPS) KW - X-Ray absorption spectroscopy (XAS) KW - photo emission electron spectroscopy (PEEM) KW - transmission electron microscopy (TEM) KW - quartz crystal micro ballance (QMB) KW - gas sensor Y1 - 2000 UR - http://www.dpg-verhandlungen.de/year/2000/conference/regensburg/part/o/session/15/contribution/1?lang=en PB - Deutsche Physikalische Gesellschaft CY - Bad Honnef ER - TY - CHAP A1 - Batchelor, David R. A1 - Follath, Rolf A1 - Schmeißer, Dieter T1 - Design of a PGM for the U49/2 Undulator at BESSY II T2 - Verhandlungen der Deutschen Physikalischen Gesellschaft N2 - This poster describes the beamline proposed for the BESSY II U49/2 Undulator by the Collaborating Research Group of BTU Cottbus, HMI Berlin and the TU Darmstadt. The beamline is designed with both high resolution electron spectroscopy, valence band measurements and PEEM in mind and utilises the wide energy range of the U49 Undulator 40−1500eV. The design chosen is based on a Petersen PGM [1] but with the grating illuminated with parallel light [2]. This modification allows variation of the monochromator higher order content or resolution, spot size without changing the focus. The performance of the beamline was investigated using various programs available at BESSY. The Undulator character- istics were evaluated using both SMUT and WAVE, and the optical performance of the monochromator was checked using REFLEC and RAY. The calculations show a resolving power of 2×104 with a flux of the order 1013 photons s−1 over the energy range covered by the mono- chromator. The maximum nominal second order contributions are ≈ 2% at 300 eV for the first Undulator harmonic and ≈ 9% for the third harmonic at 500 eV, both of which can be reduced by increasing the grating incidence angle and, or decreasing the Undulator Pinhole size. KW - Bessy II KW - undulator beamline U49/2 KW - design Y1 - 1999 UR - http://www.dpg-verhandlungen.de/year/1999/conference/muenster/part/o/session/36/contribution/81?lang=en PB - Deutsche Physikalische Gesellschaft CY - Bad Honnef ER - TY - CHAP A1 - Heller, Thomas A1 - Schmeißer, Dieter T1 - Polaronen in SrTiO3(100) T2 - Verhandlungen der Deutschen Physikalischen Gesellschaft N2 - Vorgestellt werden Untersuchungen zur elektronischen Struktur von oxidischen Halbleitern wie SrTiO3(100)-Einkristallen und WO3-Filmen. Die Charakterisierung der Oberflächen erfolgt im Valenzbandbereich mittels Photoelektronenspektroskopie (TGM 7, Bessy I, hν=3D 15-100eV). Zustände entstehen in der Bandlücke dieser=20 Materialien durch Dotierung (Heizen oder Natrium-Belegung). Wir untersuchen den Wirkungsquerschnitt speziell für diese Gapzustände. Ohne Dotierung ist der Verlauf des Wirkungsquerschnittes unstrukturiert. Bei Dotierung bilden sich molekulare Resonanzen. Deren Auftreten zeigt, daß diese Gapzustände lokalisiert sind. Weiterhin beobachten wir ausgeprägte Feinstrukturen, die die charakteristische Anregung f=FCr Polaronen enthalten. KW - Polaron KW - Röntgen-Photoelektronenspektroskopie KW - Gapzustände Y1 - 1999 UR - http://www.dpg-verhandlungen.de/year/1999/conference/muenster/part/o/session/21/contribution/8?lang=en PB - Deutsche Physikalische Gesellschaft CY - Bad Honnef ER - TY - CHAP A1 - Hoffmann, Patrick A1 - Böhme, Oliver A1 - Schmeißer, Dieter A1 - Lloyd Spetz, Anita A1 - Mårtenson, Per T1 - Einfluß von Nanopartikeln auf die Funktion von Hochtemperatursensoren T2 - Verhandlungen der Deutschen Physikalischen Gesellschaft N2 - Es werden Untersuchungen an als Hochtemperatur-Sensoren arbeitenden Schottky-Dioden mit dem Aufbau Metall-Oxidschicht-Siliziumkarbid vorgestellt. Dazu wurden Tiefenprofile mit XPS durch abwechselndes Abtragen durch Sputtern und Messen erstellt. Die Messungen erfolgten an thermisch unterschiedlich vorbehandelten Proben. Dabei konnten dipol-bedingte Verschiebungen der Bindungsenergie von Rumpfniveaus beobachtet werden. Das dazu notwendige Dipol-Moment wird durch das Entstehen von mit einer Oxidschicht überzogenen Nanoteilchen erklärt. Die unterschiedlich ausgeprägten Dipol-Verschiebungen auf den einzelnen Proben erlaubten eine Erklärung der thermischen Vorbehandlung, die bei Weglassen zu „frischen“ und je nach Temperatur zu „aktivierten“ oder „toten“ Sensoren führte. KW - Hochtemperatursensoren KW - Röntgen-Photoelektronenspektroskopie (XPS) KW - Tiefenprofilierung Y1 - 1999 UR - http://www.dpg-verhandlungen.de/year/1999/conference/muenster/part/o/session/16/contribution/1?lang=en PB - Deutsche Physikalische Gesellschaft CY - Bad Honnef ER - TY - CHAP A1 - Mikalo, Ricardo Pablo A1 - Appel, Günter A1 - Hoffmann, Patrick A1 - Schmeißer, Dieter T1 - Leitfähiges Polypyrrol als Elektrodenmaterial: Wechselwirkungen mit Silber T2 - Verhandlungen der Deutschen Physikalischen Gesellschaft N2 - Untersuchungen des metallischen Kontaktes von Silber auf tosylat- und phthalocyanindotiertem Polypyrrol wurden mittels XPS- und µ-NEXAFS vorgenommen. Es wurde festgestellt, daß Silber mit dem Polypyrrol keine Verbindung eingeht. Daraus kann geschlossen werden, daß sowohl das leitfähige Polymer, als auch das Silber ihren Leitfähigkeitsmechanismus beibehalten. Es konnte gezeigt werden, daß bei steigender Silberbelegung die Intensität der Polaronenzustände des Polypyrrol in stärkerem Maße abnimmt, als die Intensität der unbesetzten Zustände. Das läßt darauf schließen, daß Silber die Grenzfläche stabilisiert. KW - Polypyrrol KW - leifähiges Polymer KW - Röntgen-Photoelektronenspektroskopie (XPS) KW - Röntgen-Absoprtionsspektroskopie (XAS, NEXAFS) Y1 - 1999 UR - http://www.dpg-verhandlungen.de/year/1999/conference/muenster/part/o/session/11/contribution/57?lang=en PB - Deutsche Physikalische Gesellschaft CY - Bad Honnef ER - TY - CHAP A1 - Oprea, Alexandru A1 - Schmeißer, Dieter A1 - Goldenblum, A. T1 - On the charge transfer process in ZnS based ac powder electroluminescent devices T2 - Verhandlungen der Deutschen Physikalischen Gesellschaft N2 - The charge transfer process in ZnS based ac powder electroluminescent devices was experimentally and theoretically investigated. The time dependence of active currents and the voltage dependence of the brightness were measured in different operating conditions. This data allowed the hypothesis that each ZnS grain of the ac powder electroluminescent device (PWELD) behaves as a thin films electroluminescent device (TFELD) with metal-insulator-semiconductor-insulator-metal (MISIM) structure. The whole PWELD, itself, can be considered as a sum of many litle MISIM sandwiches electrically conected among them and having the quasi Fermi level of the semiconductor-insulator interface randomly distributed. On this basis, in the frame of a statistical Monte-Carlo like procedure, was developed a quantative semiclassical model, in good agreement with the experimental data. KW - ZnS KW - charge transfer process KW - ac powder electroluminescent device KW - time and brightness dependence KW - Monte Carlo simulation Y1 - 1999 PB - Deutsche Physikalische Gesellschaft CY - Bad Honnef ER - TY - CHAP A1 - Heller, Thomas A1 - Böhme, Oliver A1 - Schmeißer, Dieter T1 - Gap - Zustände in Wolframoxid WO3 - relaxierten Oberflächen T2 - Verhandlungen der Deutschen Physikalischen Gesellschaft N2 - Vorgestellt werden Arbeiten an dünnen WO3-Schichten, die durch Verdampfen aus einer Knudsenzelle im UHV präpariert wurden. Diese Filme sind im Rahmen der XPS-Analysen stöchiometrisch, ohne Gap-Zustände. Definierte Gap-Zustände bilden sich durch Relaxierung der Oberfläche: nach einigen Stunden im UHV, nach Heizen in Argon-Atmosphäre und nach Belegung mit Natrium. Die Charakterisierung dieser definierten Wolframoxid-Schichten erfolgt durch: 1.)XPS-Intensitäten 2.)detailierte Analyse der W4f-Rumpfniveaus durch Synchrotronstrahlung (Bessy, TGM 7) 3.)die Variation der Austrittsarbeit beim Heizen und bei Natrium-Belegung 4.)das Auftreten von Gap-Zuständen in der Bandlücke KW - WO3 KW - Röntgen-Photoelektronenspektroskopie (XPS) KW - Gapzustände Y1 - 1998 UR - http://www.dpg-verhandlungen.de/year/1998/conference/regensburg/part/o/session/11/contribution/102?lang=en PB - Deutsche Physikalische Gesellschaft CY - Bad Honnef ER - TY - CHAP A1 - Hoffmann, Patrick A1 - Mikalo, Ricardo Pablo A1 - Schmeißer, Dieter T1 - PEEM-Untersuchung an Spaltflächen von MoTe2-(0001) T2 - Verhandlungen der Deutschen Physikalischen Gesellschaft N2 - Molybdänditellurid (MoTe2) gehört zu den Schichtgitterverbindung und ist im allgemeinen durch den Herstellungsprozeß n-dotiert. Proben dieses MoTe2 wurden im Ultrahochvakuum gespalten und die so erhaltenen sauberen (0001)-Spaltflächen mit einem Photoemissions-Elektronenmikroskop (PEEM) untersucht. Diese Untersuchung erbrachte nebeneinander auf den Proben- oberflächen liegende stark kontrastierte helle und dunkle Bereiche. Da das PEEM Austrittsarbeitsunterschiede als Kontrast darstellt, können diese hellen und dunklen Bereiche auf lokale Unterschiede in der Austrittsarbeit zurückgeführt werden. Weiterhin wird über den Versuch berichtet, eine Zuordnung zwischen dem Kontrast und dem Unterschied in der Austrittsarbeit mit Hilfe eines Elektronenenergie-Analysators (micro-ESCA) zu treffen. KW - MoTe2 KW - Photoemissionselektronenspektroskopie (PEEM) KW - Austrittsarbeit Y1 - 1998 UR - http://www.dpg-verhandlungen.de/year/1998/conference/regensburg/part/o/session/5/contribution/5?lang=en PB - Deutsche Physikalische Gesellschaft CY - Bad Honnef ER - TY - GEN A1 - Sowinska, Małgorzata A1 - Das, Chittaranjan A1 - Wojciechowski, Konrad A1 - Rouissi, Zied A1 - Snaith, Henry J. A1 - Schmeißer, Dieter T1 - Atomic layer deposition of Al2O3 on CH3NH3PbI3 for enhancement of perovskite solar cells stability T2 - Synchrotron Radiation in Natural Science : Bulletin of the Polish Synchrotron Radiation Society KW - atomic layer deposition KW - perovskite soloar cells KW - X-ray photoelectron spectroscopy (XPS) KW - Atomic foce microscopy (AFM) Y1 - 2016 SN - 1644-7190 VL - 15 IS - 1-2 SP - S. 33 ER - TY - GEN A1 - Schmeißer, Dieter A1 - Janowitz, Christoph T1 - The Cu2p-edge of superconducting BiSrCu-Oxides studed by resonant Photoelectron Spectroscopy T2 - Synchrotron Radiation in Natural Science : Bulletin of the Polish Synchrotron Radiation Society KW - synchrotron raidation KW - superconductor Y1 - 2016 SN - 1644-7190 VL - 15 IS - 1-2 SP - S. 35 ER - TY - CHAP A1 - Das, Chittaranjan A1 - Tallarida, Massimo A1 - Schmeißer, Dieter T1 - TiO2 laminated Silicon microstructures based stable photocathode for water splitting T2 - Verhandlungen der Deutschen Physikalischen Gesellschaft N2 - The photoelectrochemical (PEC) water splitting is one of the most efficient ways to obtain hydrogen from water using solar power which can be used as carbon free fuel. The PEC device can bedesigned using semiconducting material that will convert solar radiation to H2. Silicon can be one of the best choices for PEC due to its success in solar cells technology. There are certain issues with Si such as stability in electrochemical medium [1] and higher surface reflectance (25%) which limits the Si as an ideal candidate for PEC technique [2]. In the present work we addressed these issues by surface structuring and laminating the surface with metal oxide. The microstructuring of Si was done by electrochemical method. The Si microstructure photocathode was stabilized by thin layer of ALD grown TiO2 film. The microstructuring and lamination of Si photocathode by ALD layer of TiO2 decreased the reflectance ofthe surface and shift the onset potential towards anodic direction by 350 mV with a prolonged stability over 60 hours[3]. [1] C. Levy-Clement, J. Electrochem. Soc 1991, 12, 69 [2] J. Oh, et al. Energy Environ. Sci., 2011, 4, 1690 [3] C. Das, et al. Nanoscale 2015,7, 7726 KW - water splitting KW - TiO2 KW - atomic layer deposition (ALD) KW - Si photoelectrodes Y1 - 2016 UR - http://www.dpg-verhandlungen.de/year/2016/conference/regensburg/part/ds/session/48/contribution/4?lang=en SP - S. 213 PB - Deutsche Physikalische Gesellschaft CY - Bad Honnef ER - TY - GEN A1 - Haeberle, Jörg A1 - Brizzi, Simone A1 - Gaspar, Diana A1 - Barquinha, Pedro A1 - Galazka, Zbigniew A1 - Schulz, Detlev A1 - Schmeißer, Dieter T1 - A spectroscopic comparison of IGZO thin film and the parent In2O3, Ga2O3, and ZnO single crystals T2 - Materials Research Express N2 - We use resonant photoelectron spectroscopy at the Zn 2p, Ga 2p, In 3d, and O 1s absorption edges to report on the electronic properties of indium–gallium–zinc-oxide thin films. We also compare the data with the respective data of the corresponding single crystals In2O3, Ga2O3, and ZnO. We focus on the elemental composition and, in particular, find no evidence for oxygen deficiency. The In, Ga, and Zn absorption data at resonance can be used to analyze the conduction band states in detail. We deduce that a configuration interaction between d10s0 and d9s1states is of importance. We provided a novel mechanism in which configuration interaction induced gap states create both, extended unoccupied states around E F as well as localized occupied states within the gap. KW - transparent conducting oxides (TCO) KW - resonant photoelectron spectroscopy KW - in-gapdefect states Y1 - 2016 U6 - https://doi.org/10.1088/2053-1591/3/10/106302 SN - 2053-1591 VL - 3 IS - 10 SP - 106302-1 EP - 106302-17 ER - TY - GEN A1 - Ghosh, Sujoy Kumar A1 - Biswas, Anirban A1 - Sen, Shrabanee A1 - Das, Chittaranjan A1 - Henkel, Karsten A1 - Schmeißer, Dieter A1 - Mandal, Dipankar T1 - Yb3+ Assisted Self-Polarized PVDF Based Ferroelectretic Nanogenerator: A Facile Strategy of Highly Efficient Mechanical Energy Harvester Fabrication T2 - Nano Energy N2 - Ytterbium (Yb3+) assisted porous poly(vinylidene fluoride) (PVDF) composite film comprising flexible ferroelectretic nanogenerator (FTNG) is highlighted where traditional poling treatment is completely avoided. The piezoelectric output of FTNG is realized by the co-operative activity of self-polarized -CH2/-CF2 dipoles with porous electret-like structure in the composite film. Owing to extraordinary ferroelectric and dielectric properties, FTNG is acting as a highly efficient mechanical energy harvester. It is capable to capture several forms of abundant mechanical energy arising from humanfinger movements, machine vibrations and sound waves. As a proof of concept, under compressive deformation, FTNG is enable to instantly powers up several consumer electronics and thus provides a promising strategy for achieving self-powered electronic devices. KW - PVDF KW - Yb 3+ KW - Porous ferroelectret material KW - Self-polarization KW - Ferroelectretic nanogenerator KW - Mechanical energy harvester KW - Self-powered electronics Y1 - 2016 U6 - https://doi.org/10.1016/j.nanoen.2016.10.042 SN - 2211-2855 VL - 2016 IS - 30 SP - 621 EP - 629 ER - TY - GEN A1 - Henkel, Karsten A1 - Kot, Małgorzata A1 - Schmeißer, Dieter T1 - Localized defect states and charge trapping in atomic layer deposited-Al₂O₃ films T2 - Journal of Vacuum Science and Technology, A : Vacuum, Surfaces, and Films N2 - In this study, the authors compared different Al₂O₃ films grown by atomic layer deposition (ALD) with the same aluminum precursor but on different substrates. The authors employed different process parameters such as thermal-ALD and plasma-enhanced-ALD using different substrate temperatures ranging from 280 °C down to room temperature. They characterized these films by resonant photoelectron spectroscopy and by electrical measurements. They established that generally the ALD-Al₂O₃ films show characteristic features of bulk Al₂O₃. For all films investigated, the authors found intrinsic defect states within the electronic band gap and identified excitonic, polaronic, and charge-transfer defect states. The authors gave an atomistic model to explain these intrinsic defects and found that their relative abundance is subject of the choice of ALD parameters and of the substrate used. They were able to relate the spectroscopic assigned in-gap defect states with the electronic charges as determined in our electrical measurements. KW - defect states KW - resonant photoelectron spectroscopy (resPES) KW - Al₂O₃ KW - atomic layer deposition (ALD) KW - excitons KW - polarons Y1 - 2017 U6 - https://doi.org/10.1116/1.4971991 SN - 0734-2101 SN - 1520-8559 VL - 35 IS - 1 SP - 01B125-1 EP - 01B125-18 ER - TY - GEN A1 - Kot, Małgorzata A1 - Das, Chittaranjan A1 - Wang, Zhiping A1 - Henkel, Karsten A1 - Rouissi, Zied A1 - Wojciechowski, Konrad A1 - Snaith, Henry J. A1 - Schmeißer, Dieter T1 - Room-Temperature Atomic Layer Deposition of Al₂O₃: Impact on Efficiency, Stability and Surface Properties in Perovskite Solar Cells T2 - ChemSusChem N2 - In this work, solar cells with a freshly made CH₃NH₃PbI₃ perovskite film showed a power conversion efficiency (PCE) of 15.4 % whereas the one with 50 days aged perovskite film only 6.1 %. However, when the aged perovskite was covered with a layer of Al₂O₃ deposited by atomic layer deposition (ALD) at room temperature (RT), the PCE value was clearly enhanced. X-ray photoelectron spectroscopy study showed that the ALD precursors are chemically active only at the perovskite surface and passivate it. Moreover, the RT-ALD-Al2O3-covered perovskite films showed enhanced ambient air stability. KW - Al₂O₃ KW - atomic layer deposition (ALD) KW - perovskite KW - solar cells KW - X-ray photoelectron spectroscopy (XPS) Y1 - 2016 U6 - https://doi.org/10.1002/cssc.201601186 SN - 1864-5631 SN - 1864-564X VL - 9 IS - 24 SP - 3401 EP - 3406 ER - TY - GEN A1 - Cuypers, Daniel A1 - Fleischmann, Claudia A1 - Dorp, Dennis H. von A1 - Brizzi, Simone A1 - Tallarida, Massimo A1 - Müller, Matthias A1 - Hönicke, Philipp A1 - Billen, Arne A1 - Chintala, Ravi A1 - Conard, Thierry A1 - Schmeißer, Dieter A1 - Vandervorst, Wilfried A1 - Elshocht, Sven van A1 - Armini, Silvia A1 - De Gendt, Stefan A1 - Adelmann, Christoph T1 - Sacrificial Self-Assembled Monolayers for the Passivation of GaAs(100) Surfaces and Interfaces T2 - Chemistry of Materials N2 - The use of sacrificial self-assembled monolayers (SAMs) to prepare clean n-type GaAs (100) surfaces without band bending in vacuo is demonstrated. GaAs surface passivation using octadecanethiol SAMs after HCl cleaning is shown to lead to an enhancement of the room-temperature photoluminescence intensity. Synchrotron-radiation photoelectron spectroscopy (SRPES) finds that the interfacial oxide between GaAs and the SAM remains below the detection limit. Evidence for both Ga–S and As–S bonds at the GaAs–thiolate interface is found. The limited thermal stability of the SAM allows the desorption of the alkyl chains by in situ thermal annealing at temperatures above 180 °C, leaving S bonded to Ga behind. The resulting surface contains only a very small amount of O (0.05 ML coverage) and C (about 3% of the SAM remaining) and shows no band bending with the surface Fermi level close to the conduction band. Atomic layer deposition of Al₂O₃ on this surface occurs via the formation of Al–S bonds without introducing any additional band bending. This indicates that the surface preparation of n-type GaAs (100) using sacrificial octadecanethiol SAMs followed by in situ thermal removal provides a route toward GaAs/oxide interfaces without interfacial oxides and without band bending. KW - GaAs KW - passivation KW - Al₂O₃ KW - atomic layer deposition (ALD) KW - Synchrotron-radiation photoelectron spectroscopy (SRPES) KW - self assembled monolayers (SAM) KW - interface engineering Y1 - 2016 U6 - https://doi.org/10.1021/acs.chemmater.6b01732 SN - 0897-4756 SN - 1520-5002 VL - 28 IS - 16 SP - 5689 EP - 5701 ER - TY - GEN A1 - Corrêa, Silma Alberton A1 - Brizzi, Simone A1 - Schmeißer, Dieter T1 - Depicting the Electronic Structure of HfO₂ Films by Spectroscopic Techniques T2 - ECS Transactions N2 - The electronic structure of HfO₂ films was investigated. The partial density of states for the valence and the conduction bands was determined by the detailed analysis of the O1s resonance profile by resonant photoelectron spectroscopy. The positions of valence band maximum and conduction band minimum, the excitation range for the polaronic states and the range of charge transfer band were found to be not influenced by the preparation conditions. The band gap was determined to be 6.2 eV and the energy of the charge neutrality level (referred to vacuum level) was determined as 4.7 eV. The Fermi level position was observed to vary about 1.2 eV depending on the preparation conditions, which indicates the presence of charges within the films. KW - HfO₂ KW - resonant photoelectron spectroscopy (resPES) KW - electronic structure KW - partial density of states KW - charge neutrality level Y1 - 2016 U6 - https://doi.org/10.1149/07506.0145ecst SN - 1938-6737 SN - 1938-5862 VL - 75 IS - 6 SP - 145 EP - 153 ER - TY - GEN A1 - Henkel, Karsten A1 - Das, Chittaranjan A1 - Kot, Małgorzata A1 - Schmeißer, Dieter A1 - Naumann, Franziska A1 - Kärkkänen, Irina A1 - Gargouri, Hassan T1 - In-gap states in titanium dioxide and oxynitride atomic layer deposited films T2 - Journal of Vacuum Science and Technology: A N2 - Valence band (VB) spectra of titanium dioxide (TiO2) and oxynitride (TiOxNy) films prepared by different atomic layer deposition (ALD) processes are compared and related to electrical characterization [current–voltage (JV) and capacitance–voltage (CV)] results. By increasing the nitrogen amount in the TiO2 film, band-gap narrowing is observed. The band-gap decrease is related to the contribution of the nitrogen density of states, which induces defects within the band-gap and thus reduces its optical band-gap. In-gap states are found in the VB spectra at 1 eV below the Fermi energy in all investigated ALD samples, i.e., in TiO2 as well as in TiOxNy films. An exponential correlation between leakage current density and in-gap state intensity is derived by the combination of JV measurements and VB spectra, whereas the in-gap states seem to have no influence on hysteresis and fixed oxide charges found in the CV data. It is argued that the in-gap states in TiO2 and TiOxNy have an excitonic or polaronic origin. Both, band-gap narrowing and in-gap state intensity can be tuned by the ALD process selection and the variation of its parameters. KW - Titanium dioxide (TiO2) KW - Titanium oxynitrdie (TiON) KW - valence band spectra KW - in-gap states KW - band-gap narrowing KW - electrical characterization Y1 - 2017 U6 - https://doi.org/10.1116/1.4972247 SN - 0734-2101 SN - 1520-8559 VL - 35 IS - 1 SP - 01B135-1 EP - 01B135-8 ER - TY - CHAP A1 - Garain, Samiran A1 - Adhikary, Prakriti A1 - Mandal, Dipankar A1 - Sen, Shrabanee A1 - Henkel, Karsten A1 - Schmeißer, Dieter T1 - Electro-active β-Phase Formation in Poly(vinylidene fluoride) Films by Hydrated Rare earth Metal Salt T2 - Proceeding of the International Conference on Nanotechnology 2013 (ICNT 2013) N2 - Polyvinylidene fluoride (PVDF) is a typical fluoro-polymer with complicated polymorphisms due to the semi-crystalline nature. Generally, four crystalline phases, α, β, γ and δ may exist in PVDF crystals. The nonpolar α- and δ-phase has a monoclinic lattice with trans-gauche conformation (TGTG⁄), which is thermodynamically most stable for PVDF. The polar β phase with all-trans (TTTT) planar zigzag conformation is attractive for its piezo-, pyro-, and ferroelectric properties. The polar β-Phase and also semi-polar γ-phase (TTTGTTTG⁄) have obtained wide device applications such as acoustic transducers, piezoelectric sensors, energy harvesting generators, pyroelectric sensors, non-volatile memories and energy storage capacitors. In this work, we explore the possibility to nucleate β-phase in PVDF hydrated salt composite films by addition of the hydrated Rare earth metal salt, (NH4)4 Ce (SO4)4, 2H2O) for the piezo- ferro and high dielectric based device applications. It has been found that the water molecules in (NH4)4 Ce (SO4)4, 2H2O could form hydrogen bonds with PVDF during the crystallization process and the hydrogen bonds promoted the electro-active crystalline β- phase in PVDF with all -trans conformations. In addition, the DMF (solvent used for films preparation) can also assist the rare-earth based nanoparticle preparation, as a result the electrostatic interaction of the surface charge of the nanoparticles and molecular dipoles in PVDF can resist the electroactive β- phase in PVDF. KW - PVDF KW - β-Phase KW - piezoelectric Y1 - 2013 SN - 978-81-927756-0-9 SP - S. 127 PB - Institute of Technology, Haldia, WB, India CY - Haldia ER - TY - CHAP A1 - Schmeißer, Dieter A1 - Müller, Sebastian A1 - Henkel, Karsten A1 - Müller, Klaus A1 - Wehner, Stefan T1 - In-situ analysis of moving reaction fronts for the bistable CO oxidation reaction on noble metal catalyst T2 - Extended Abstracts Book of First International Conference on Materials for Energy N2 - Experimental data on the reaction kinetics of catalytic processes are prerequisite for modeling of such reactions and their output. We investigate the CO oxidation on some noble metal catalysts, like Iridium(111) and Palladium(111) which is a bistable surface reaction. In a specific range of CO content in the feed gas islands of one or the other adsorbate nucleate and grow, which is recorded with photo electron emission microscopy (PEEM). During these transients the coverage on the surface changes from predominantly oxygen covered to predominantly CO covered resp. vice versa. But the resolution of PEEM and especially its unknown and nonlinear dependence of coverage of the two adsorbates (oxygen and CO) and image intensity make it impossible to extract the changes in coverage. On the other hand the reaction diffusion model based on the Langmuir-Hinshelwood-mechanism delivers the coverage of oxygen and carbon monoxide. The shapeand wall velocity of those islands has been connected perfectly to each other [CPL 423 (2006) 39], but not the absolute coverage and their variation during the reaction. Since the domain wall velocity is small on Iridium(111), this has opened the possibility for a detailed analysis of the changing coverage inside this domain wallutilizing synchrotron radiation and photo electron spectroscopy at BESSY II. The coverage profile of oxygen and CO inside a moving domain wall was measured for both cases using XPS spectra at O1s, C1s and the valence band during thereaction. Comparison with the reaction-diffusion-model and other catalytic surfaces, like Palladium(111) are done. KW - CO oxidation KW - Ir KW - Pd KW - photo electron emission microscopy (PEEM) Y1 - 2010 SN - 978-3-89746-117-8 SP - S. 932 PB - Dechema e.V. CY - Frankfurt ER - TY - GEN A1 - Menezes, Prashanth W. A1 - Indra, Arindam A1 - Das, Chittaranjan A1 - Walter, Carsten A1 - Göbel, Caren A1 - Gutkin, Vitaly A1 - Schmeißer, Dieter A1 - Driess, Matthias T1 - Uncovering the Nature of Active Species of Nickel Phosphide Catalysts in High-Performance Electrochemical Overall Water Splitting T2 - ACS Catalysis N2 - A systematic structural elucidation of the near-surface active species of the two remarkably active nickel phosphides Ni12P5 and Ni2P on the basis of extensive analytical, microscopic, and spectroscopic investigations is reported. The latter can serve as complementary efficient electrocatalysts in the hydrogen (HER) versus oxygen evolution reaction (OER) in alkaline media. In the OER Ni12P5 shows enhanced performance over Ni2P due to the higher concentration of nickel in this phase, which enables the formation of an amorphous NiOOH/Ni(OH)2 shell on a modified multiphase with a disordered phosphide/phosphite core. The situation is completely reversed in the HER, where Ni2P displayed a significant improvement in electrocatalytic activity over Ni12P5 owing to a larger concentration of phosphide/phosphate species in the shell. Moreover, the efficiently combined use of the two nickel phosphide phases deposited on nickel foam in overall electrocatalytic water splitting is demonstrated by a strikingly low cell voltage and high stability with pronounced current density, and these catalysts could be an apt choice for applications in commercial alkaline water electrolysis. KW - overall water splitting KW - electrocatalysis KW - nickel phosphide KW - structural rearrangement KW - surface structure Y1 - 2017 U6 - https://doi.org/10.1021/acscatal.6b02666 SN - 2155-5435 VL - 7 IS - 1 SP - 103 EP - 109 ER - TY - GEN A1 - Indra, Arindam A1 - Menezes, Prashanth W. A1 - Das, Chittaranjan A1 - Göbel, Caren A1 - Tallarida, Massimo A1 - Schmeißer, Dieter A1 - Driess, Matthias T1 - A facile corrosion approach to the synthesis of highly active CoOxwater oxidation catalysts T2 - Journal of Materials Chemistry A N2 - Ultra-small rock salt cobalt monoxide (CoO) nanoparticles were synthesized and subjected to partial oxidation (‘corrosion’) with ceric ammonium nitrate (CAN) to form mixed-valence CoOx(1 < x< 2) water oxidation catalysts. Spectroscopic, microscopic and analytical methods evidenced a structural reformation of cubic CoO to active CoOx with a spinel structure. The superior water oxidation activity of CoOx has been established in electrochemical water oxidation under alkaline conditions. Electrochemical water oxidation with CoOx was recorded at a considerably low overpotential of merely 325 mV at a current density of 10 mA cm-2 in comparison to 370 mV for CoO. Transformation of both octahedral CoII and CoIII sites into amorphous Co(OH)2–CoOOH is the key to high electrochemical activity while the presence of a higher amount of octahedral CoIII sites in CoOx is imperative for an efficient oxygen evolution process. KW - water splitting KW - water oxidation KW - cobalt oxide catalyst KW - transmission electron microscopy (TEM) KW - X-ray photoelectron spectroscopy (XPS) KW - X-ray absorption spectroscopy (XAS) KW - Cyclic voltammetry (CV) Y1 - 2017 U6 - https://doi.org/10.1039/c6ta10650a SN - 2050-7488 SN - 2050-7496 IS - 5 SP - 5171 EP - 5177 ER - TY - CHAP A1 - Łobaza, Justyna A1 - Kot, Małgorzata A1 - Schmeißer, Dieter T1 - Analysis of surface oxidation of TiON ALD films T2 - Verhandlungen der Deutschen Physikalischen Gesellschaft N2 - Titanium oxynitride (TiON) films are interesting due to their remarkable optical and electronic properties which strongly depend on the O/N ratio. However, it is known that films containing Ti are prone to oxidation in contact with the air [1]. In this work, we study the thickness of a surface oxidation layer which is inherently formed on the atomic layer deposition (ALD) grown TiON/TiN films on Si substrate. We use an Ar+ ion bombardment source and X-ray photoelectron spectroscopy (XPS) for this analysis. We calibrate the sputter rate by using substrate signal intensity decay (here Si 2p) in the XPS spectra of the 5 nm thick TiON sample accordingly. This rate is assumed to be constant when films with a larger thickness are analyzed. We find that the surface oxidation layer is about 1 nm thick, independent on the detailed ALD parameters of the films. The TiN films found underneath are close to the stoichiometric values and have a residual O content below 5%. Finally, we compare these data to our previous results collected with synchrotron-based radiation source [2,3]. References: [1] Sowinska et al., Applied Physics Letters 100, 233509 (2012). [2] M. Sowinska et al., Applied Surface Science 381, 42-47 (2016). [3] M. Sowińska et al., Journal of Vacuum Science and Tech- nology A, 01A12734 (2016). KW - titanium oxynitride KW - X-Rax photoelectron spectroscopy KW - depth profiling KW - sputtering Y1 - 2017 UR - http://www.dpg-verhandlungen.de/year/2017/conference/dresden/part/ds/session/21/contribution/7 SN - 0420-0195 SP - S. 202 PB - Deutsche Physikalische Gesellschaft CY - Bad Honnef ER - TY - CHAP A1 - Kot, Małgorzata A1 - Wojciechowski, Konrad A1 - Snaith, Henry J. A1 - Schmeißer, Dieter T1 - Characterization of the perovskite solar cells containing atomic layer deposited Al2O3 buffer layer T2 - Verhandlungen der Deutschen Physikalischen Gesellschaft e.V. N2 - Hybrid perovskites have potential to overcome performance limits of the current solar cell technologies and achieve low cost and high versatility. Nonetheless, they are prone to degradation in presence of moisture within a couple of hours or days. In this work, we use the atomic layer deposition (ALD) of Al2O3 on the CH3NH3PbI3 perovskite at room temperature in order to verify if this thin ALD layer may protect the perovskite film against moisture degradation and to check the impact of the Al2O3 on the solar to power conversion efficiency (PCE). Depth profiling X-ray photoelectron spectroscopy study shows that the ALD precursors are chemically active only at the perovskite surface and the film bulk is not affected. The perovskite film coated with Al2O3 layer has enhanced moisture stability. Solar cells with a fresh-made CH3NH3PbI3 perovskite film have shown PCE of 15.4%, while the one with 50 days aged perovskite only 6.1%. However, when the aged perovskite is covered with RT-ALD-Al2O3 the PCE value is clearly enhanced.[1] [1] M. Kot et al., Room temperature ALD impact on efficiency, stability and surface properties in perovskite solar cells, ChemSusChem,acctepted. KW - Perovskite solar cell KW - atomic layer deposition KW - Al2O3 KW - efficiency recovery Y1 - 2017 UR - http://www.dpg-verhandlungen.de/year/2017/conference/dresden/part/cpp/session/38/contribution/5 SN - 0420-0195 SP - S. 147 PB - Deutsche Physikalische Gesellschaft CY - Bad Honnef ER - TY - CHAP A1 - Henkel, Karsten A1 - Kot, Małgorzata A1 - Schmeißer, Dieter T1 - Localized defect states and charge trapping in Al₂O₃ films prepared by atomic layer deposition T2 - Verhandlungen der Deutschen Physikalischen Gesellschaft N2 - The evaluation of the electronic structure and intrinsic defect mechanisms in Al₂O₃ thin films is essential for their effective use in applications with desired functionality such as surface passivation schemes for solar cells [1]. We present a comparative study of different Al₂O₃ films grown by atomic layer deposition (ALD) [2]. The layers were deposited on different substrates using the same aluminum precursor (TMA, trimethylalumium) and employing different process parameters (thermal-ALD, plasma-enhanced-ALD, substrate temperature). These films were characterized by resonant photoelectron spectroscopy and by electrical measurements (capacitance-voltage). For all films investigated intrinsic defect states within the electronic band gap were observed including excitonic, polaronic, and charge-transfer defect states, where their relative abundance is subject of the choice of ALD parameters and of the used substrate. The spectroscopic assigned in-gap defect states are related with electronic charges as determined in the electrical measurements. [1] G. Dingemans and W.M.M. Kessels, J. Vac. Sci. Technol. A 30, 040802 (2012). [2] K. Henkel, M. Kot, D. Schmeißer, J. Vac. Sci. Technol. A 35, (2017), accepted. KW - defect states KW - Al₂O₃ KW - resonant photoelectron spectroscopy KW - X-Ray absorption spectroscopy KW - capacitance-voltage measurements Y1 - 2017 UR - http://www.dpg-verhandlungen.de/year/2017/conference/dresden/part/ds/session/32/contribution/4 SN - 0420-0195 SP - S. 205 PB - Deutsche Physikalische Gesellschaft CY - Bad Honnef ER - TY - CHAP A1 - Israel, Johannes A1 - Rachow, Fabian A1 - Schwiertz, Carola A1 - Charlafti, Evgenia A1 - Müller, Klaus A1 - Schmeißer, Dieter T1 - Direct CO2-Methanation of flue gas emitted by conventional power plants T2 - Verhandlungen der Deutschen Physikalischen Gesellschaft N2 - The catalytic conversion of CO2 with H2 into CH4 is possible by the Sabatier reaction CO2+4H2→CH4+2H2O. Using excess energy from renewable electricity generation, this approach offers an opportunity for recycling of CO2 as synthetic natural gas. In a new concept, we investigate the performance of the Sabatier reaction as direct methanation of flue gas, emitted by conventional power plants. We investigate the Sabatier process in an upscaled system, with a maximum input flow rate of 45 Nm3/h Gas. The performance is investigated in a simulated composition of flue gas and under real conditions at a lignite power plant in Schwarze Pumpe, Brandenburg, Germany. We can achieve a CO2-conversion of up to 90%, with approx. 100% selectivity towards CH4. Under flue gas conditions and at a certain limit of gas flow the system is operated at an autothermal running modus, a steady state equilibrium of exothermic heat production and thermal flow that needs neither external annealing nor cooling. KW - CO2 KW - methanation KW - Sabatier reaction KW - power plant KW - Schwarze Pumpe KW - autothermal mode Y1 - 2017 UR - http://www.dpg-verhandlungen.de/year/2017/conference/muenster/part/ake/session/8/contribution/5 SP - S. 255 PB - Deutsche Physikalische Gesellschaft CY - Bad Honnef ER - TY - CHAP A1 - Rachow, Fabian A1 - Hagendorf, Moritz A1 - Müller, Klaus A1 - Schmeißer, Dieter T1 - Synthesis of Methanol from CO2 for Power-to-Liquid applications T2 - Verhandlungen der Deutschen Physikalischen Gesellschaft N2 - The direct synthesis of methanol [CO2+3H2->CH3OH+H2O] represent a possibility to reduce the global CO2-emission by recycling the CO2 and also to store excess energy from renewable energy sources into a common fuel or chemical feedstock (Power-to-Liquid). For an acceptable conversion rate of CO2 a catalyst is needed, together with high temperatures (>200°C) and high pressure (50-200bar). Methanol is normally produced form synthesis gas, a mixture of CO and H2. By directly using CO2 for the exothermic reaction, we avoid the conversion of CO2 to CO by the reversed water gas shift reaction. We also present new concepts for the conversion from CO2-rich flue gases, eliminating the need for a separation of the CO2. The concept is backed up by measurements in laboratory scale. Here we use a Cu−ZnO catalyst on a ZrO2 substrate prepared by impregnation and compare the results with commercially available catalysts. We achieved a conversion of around 7% and a selectivity of 60% at a temperature of 240°C and 45bar. The reaction is thermodynamically limited with a maximum conversion rate of 15% at 250°C and 50bar. The conversion and the selectivity towards methanol is highly influenced by the catalyst used, the temperature, the pressure as well as the flow rate of the reactants. KW - direct methanol synthesis KW - power to liquide KW - Cu-ZnO catalyst KW - CO2 utilization Y1 - 2017 UR - http://www.dpg-verhandlungen.de/year/2017/conference/muenster/part/ake/session/8/contribution/5 SP - S. 256 PB - Deutsche Physikalische Gesellschaft CY - Bad Honnef ER - TY - GEN A1 - Das, Chittaranjan A1 - Kot, Małgorzata A1 - Rouissi, Zied A1 - Kędzierski, Kamil A1 - Henkel, Karsten A1 - Schmeißer, Dieter T1 - Selective Deposition of an ultrathin Pt Layer on a Au-Nanoisland-Modified Si Photocathode for Hydrogen Generation T2 - ACS Omega N2 - Platinum, being the most efficient and stable catalyst, is used in photoelectrochemical (PEC) devices. However, a minimal amount of Pt with maximum catalytic activity is required to be used to minimize the cost of production. In this work, we use an environmentally friendly, ost-effective, and less Pt-consuming method to prepare PEC devices for the hydrogen evolution reaction (HER). The Pt monolayer catalyst is selectively deposited on a Au-nanoisland-supported boron-doped p-type Si (100) photocathode. The PEC device based on the Si photocathode with an ultralow loading of the Pt catalyst exhibits a comparable performance for the HER to that of devices with a thick Pt layer. In addition, we demonstrate that by using a thin TiO2 layer deposited by atomic layer deposition photo-oxidation of the Si photocathode can be blocked resulting in a stable PEC performance. KW - water splitting KW - hydrogen evolution reaction (HER) KW - Si photocathode KW - gold nanoislands KW - nanostructured platinum Y1 - 2017 U6 - https://doi.org/10.1021/acsomega.6b00374 SN - 2470-1343 VL - 2 IS - 4 SP - 1360 EP - 1366 ER -