TY - JOUR A1 - Viehweger, Bernd A1 - Simon, Sylvio A1 - Wagner, Lothar A1 - Schmeißer, Dieter T1 - Entwicklung eines neuartigen Fügeverfahrens für die Herstellung von Aluminium-Stahl-Tailored Blanks N2 - Die Anwendung von Tailored Blanks im Karosseriebau trägt wesentlich zur Gewichtsreduzierung und damit zur Kraftstoffeinsparung an Fahrzeugen bei. Bisher bekannte Tailored Blanks aus Aluminium und Stahl werden mittels Laserschweißen überlappend gefügt. Für ein Aluminium-Stahl-Tailored Blank wurde ein Verfahren entwickelt, das die Herstellung desselben durch ein umformendes Fügeverfahren ermöglicht. Unter Berücksichtigung der Erkenntnisse des Kaltpressschweißens wird mittels eines Walzvorganges eine Fügung erreicht. Dadurch wird ein Aufschmelzen der Fügepartner und die damit eventuell verbundene Bildung interkristalliner Zonen verhindert. Der Walzvorgang verhindert gleichzeitig die bei Kaltpressschweißen sonst üblichen Kerben. Durch eine anschließende Wärmebehandlung lässt sich die Festigkeit der Verbindung steigern. Das Aluminium-Stahl-Tailored Blank kann in verschiedenen Abmessungen gefertigt werden und ist blecheben. KW - Fügen durch Umformen KW - Kaltpressschweißen KW - Stahl-Aluminium-Verbund Y1 - 2002 ER - TY - JOUR A1 - Hoffmann, Patrick A1 - Mikalo, Ricardo Pablo A1 - Schmeißer, Dieter T1 - Si(001) surface oxidation by N2O N2 - Ultra-thin homogeneous oxynitride films are prepared on Si(001). The Si surface is cleaned in UHV by heating (flashing) and is exposed to different pressures of N2Oat altered temperatures. Thus oxynitride layers of different thickness and different properties are grown depending on the N2O pressure and the Si temperature. This isillustrated by a schematic diagram. The properties of the different oxynitride layers were studied by a combined photoemission electron microscopy (PEEM) andphotoelectron spectroscopy (PES) investigation using highly monochromatic synchrotron radiation. The amount of oxygen and nitrogen incorporated in the oxynitridelayers is determined from the PES measurements. The typical surface morphology for different preparation conditions is shown in PEEM images. KW - SI(100) KW - dielectric KW - Oxynitride KW - Interface KW - SI KW - NO Y1 - 2002 ER - TY - JOUR A1 - Mikalo, Ricardo Pablo A1 - Schmeißer, Dieter T1 - Electric contacts on conductive polymers: sodium on poly(3-hexylthiophene-2,5-diyl) N2 - Sodium as a model contact with low work function on regioregular poly(3-hexylthiophene-2,5-diyl) (P3HT) films was investigated. The interface was studied by X-rayand ultraviolet photoelectron spectroscopy in the range of 0.13 up to 1.8 metal atoms per hexylthiophene unit. In the range of 0.13-0.26 sodium atoms per hexylthiophenering we find a change inthe surface potentials which is interpreted as a discharge of positive surface charges. Sodium exposures above 0.5 sodium atoms perhexylthiophene unit exhibit a reduction of the thiophene sulfur due to the formation of sodium sulfide and breaking of the thiophene ring. Y1 - 2002 ER - TY - JOUR A1 - Yfantis, Alexandros D. A1 - Paloumpa, Ioanna A1 - Schmeißer, Dieter A1 - Yfantis, Alexandros D. T1 - Novel corrosion-resistant films for Mg alloys N2 - A novel method for the corrosion inhibition of Mg, alloys, based on the formation of a thin polyacrylic-polypyrrole film, is presented. The film was created after simpleimmersion of the samples in a specially formulated emulsion of polyacrylic and polypyrrole polymers. The synthesis conditions were studied, as well as the resultingcorrosion resistance of coated magnesium foils (AZ31) in terms of corrosion rate in neutral aqueous NaCl solutions. The relative ratio of polyacrylic polymer topolypyrrole was found to be important for the film properties. Furthermore, only in situ polymerisation of pyrrole in the polyacrylic emulsion can provide advancedcorrosion proper-ties in relatively thin films (2-5 mum). Blending of polypyrrole powder with the polyacrylic emulsion gives rise to thick films (20 mum) with reducedcorrosion-inhibition properties. The corrosion rate was only weakly dependent on the film thickness of these novel coatings. We argue that the mechanism of corrosioninhibition is related to the formation of a thin passive layer of chemisorbed polypyrrole polymers or oligomers on the native magnesium oxide of the C surface. Thestructure is further stabilised by polyacrylic polymer chains interacting as dopants of polypyrrole. The method is environmentally friendly: non-toxic chemicals are used,no rinsing is required, etc. The advanced corrosion-inhibition properties of the films. as well as the simple application process on the metal surface, provide significantpotential for the industrial application of the method. KW - polypyrrole KW - polyacrylic KW - coating KW - magnesium KW - corrosion inhibition Y1 - 2002 ER - TY - GEN A1 - Aggour, Mohammed A1 - Stoerkel, Ulrich A1 - Murrell, Chris A1 - Campbell, S. A. A1 - Jungblut, H. A1 - Hoffmann, Patrick A1 - Mikalo, Ricardo Pablo A1 - Schmeißer, Dieter A1 - Lewerenz, Hans-Joachim T1 - Electrochemical interface modification of CuInS2 thin films N2 - We studied two novel electrochemical treatments of CuInS2 solar-cell absorber films, introduced to remove the deleterious segregated CuS phase. Their influence onsurface topography, chemistry and electronic properties was investigated using in situ atomic force microscopy (AFM) and photoclectron spectroscopy, performed inpart at the U49/2 undulator beam line at BESSY II. The results are examined in order to develop an improved understanding of the chemical-electrochemical surfacetransformation processes. KW - thin-film solar cells KW - copper indium disulfide KW - atomic force microscopy (AFM) KW - photoelectron spectroscopy KW - synchrotron radiation KW - Solar-Cell Y1 - 2002 ER - TY - JOUR A1 - Hoffmann, Patrick A1 - Mikalo, Ricardo Pablo A1 - Schmeißer, Dieter T1 - PEEM - a spectromicroscopic tool for mc-Si surface evaluation N2 - The photo emission electron microscope (PEEM) with its direct imaging of the sample surface is a convenient tool for fast evaluation of large sample areas. It is possibleto handle samples with a size of 30 mm x 30 mm.With PEEM it is possible to visualise grain boundaries and crystal displacements without removing the native oxide. No special sample treatment is needed exceptchemical polishing of the sample surface and a HF-dip to obtain a thin (1 ... 2 nm) oxide layer.The quality of that oxide was proofed by high resolution photo electron spectroscopy (PES) at a synchrotron. The results were compared to native oxide onsingle-crystalline Si and no suboxides (e.g. SiO) were found. Our spectromicroscopic PEEM measurements show no difference in the oxide qualities of different grainsand on grain boundaries or crystal displacements. Furthermore no difference in the binding energy of Si2p core levels were found.In addition to grain boundaries other spot-like features were found on the sample surface. These could be identified in some cases as precipitation of Ca underneath thenative oxide. KW - multicrystalline silicon KW - photoelectron spectroscopy KW - PEEM Y1 - 2002 ER - TY - GEN A1 - Müller, Klaus A1 - Henkel, Karsten A1 - Mikalo, Ricardo Pablo A1 - Paloumpa, Ioanna A1 - Schmeißer, Dieter T1 - Elektronik mit organischen Materialien N2 - Plastikelektronik, flexible Solarzellen, intelligente Kleidung, neuartige und maßgeschneiderte Transducer für die Gas-, Flüssigkeits- und Biosensorik, all dies sind Anwendungen, die ohne halbleitende Polymere nicht denkbar wären und die Bereiche erschließen, in denen zur Zeit eine regelrechte Goldgräberstimmung herrscht. Mit wichtigen Beiträgen im Grundlagen- und Anwendungsbereich nimmt die BTU Cottbus an dieser Entwicklung teil, u. a. auch durch eine Kooperation mit dem Institut für Mikrobiologie des Carl-Thiem-Klinikums Cottbus.In diesem Artikel werden die Voraussetzungen für die Konstruktion organischer Feldeffekt-Transistoren mit gassensitiver Gate-Elektrode vorgestellt. Untersuchungen zur elektronischen Struktur des organischen Halbleiters Poly(3-Hexylthiophen), die Anwendung dieses Materials als aktive Schicht in organischen Feldeffekt-Transitoren, die Gassensitivität von Polypyrrolelektroden auf Quarz-Mikrowaagen und die Mikrorstukturierung organischer Elektroden werden beschrieben. Y1 - 2002 PB - BTU Cottbus, Eigenverlag ER - TY - CHAP A1 - Schwiertz, Carola A1 - Henkel, Karsten A1 - Paloumpa, Ioanna A1 - Schmeißer, Dieter T1 - Sensorsystem zur Unterscheidung von Geruchsmustern in Tierställen N2 - Es wurde ein kontinuierlich arbeitendes, preiswertes Schwingquarz-Mess-System zur olfaktometrischen Überwachung von Tierställen aufgebaut, mit dessen Hilfe im Arbeitsbereich von 65%B0C spezifische Gerüche verschiedener Tierarten unterschieden werden können. Zur Geruchsmustererkennung wurde ein einfaches neuronales Netz verwendet. Olfaktometrische Verdünnungen auf 33% sowie Messwertschwankungen von 5-10% wurden simuliert, wobei die richtige Musterzuordnung durch das Netz nicht beeinflusst wurde. Y1 - 2002 ER - TY - CHAP A1 - Henkel, Karsten A1 - Hoffmann, Patrick A1 - Schmeißer, Dieter T1 - Backpropagation-Netzwerke für ein Zweisensorsystem zur Erfassung von Kohlendioxidkonzentrationen und relativer Luftfeuchte T2 - Sensoren im Fokus neuer Anwendungen : Verbraucherschutz und Lebensmittelkontrolle, Biosysteme und Nanobiotechnologie, Umweltmesstechnik, neue Sensormaterialien, Mess- und Eichwesen N2 - Zwei Schwingquarzsensoren mit gleicher sensitiver Beschichtung wurden zur Messung von CO2-Konzentrationen bei variierenden Luftfeuchten genutzt. Die Daten wurden neuronalen Netzen mit unterschiedlicher Architektur trainiert. Zwei Netze wurden auf ihre Generalisierungsfähigkeit getestet und miteinander verglichen. Für ein einstufiges Netz konnten Ergebnisse mit Fehlern kleiner 12% für die CO2-Konzentration und kleiner 5% für die Luftfeuchte erzielt werden. Ein zweistufiges Netz erkannte Kategorien der Luftfeuchte 100%-ig, für die CO2-Konzentration wurden Fehler kleiner 9% erreicht, wobei eine deutlich bessere Generalisierungsfähigkeit dieses Netzes im Vergleich zum einstufigen Netz zu verzeichnen ist. Y1 - 2002 SN - 3-935712-71-5 SN - 978-3-935712-71-2 SP - 104 EP - 107 PB - w.e.b. Universitätsverlag CY - Dresden ER - TY - CHAP A1 - Müller, Klaus A1 - Henkel, Karsten A1 - Paloumpa, Ioanna A1 - Schmeißer, Dieter T1 - Low-cost-Plot-Technologie fur die Mikrostrukturierung von Gassensoren T2 - Sensoren im Fokus neuer Anwendungen, 5. Dresdner Sensor-Symposium, 10. - 12. Dezember 2001, Dresden N2 - Bei der Herstellung von Mikrosensoren ist die Strukturierung von Elektroden oder elektrischen Zu-leitungen mit einem hohen Miniaturisierungsgrad ein entscheidender Punkt. Dazu müs-sen häufig teure Verfahren (Lithographie, Maskentechniken) herangezogen werden.Dieser Beitrag beschreibt eine low-cost-Technologie zur Herstellung organischer Mikrostrukturen für elektronische und messtechnische Anwendungen im Bereich der Sensorik. Geplottete Strukturen mit Polypyrrol und Poly(3,4-Ethylen-Dioxy-Thiophen), dotiert mit Polystyrolsulfonat (PEDOT/PSS) wurden als Widerstandssensoren für die Detektion von Luftfeuchte ein-gesetzt. Die prinzipielle Ein-satzmöglichkeit unserer Technik im Bereich der organischen Elektronik konnten wir mit dem Bau organischer Feldeffekttransistoren nachweisen. Mit einem computergesteu-erten Plotter des Typs Rol-land DXY-1150A, Plot-Kapillaren für das Tuschezeichnen, handelsüblichen Folien für wasserlösliche Tinten als Substrat und kolloidalen Graphit als leitendes Material konnten wir Auflösungen, das heißt insbesondere Kanalbreiten bzw. Elektrodenabstände im Bereich von 20+10%B5m (auf 2cm Länge) her-stellen. Y1 - 2002 SN - 3-935712-71-5 SP - 166 EP - 169 PB - w.e.b. Universitätsverlag CY - Dresden ER -