TY - GEN A1 - Kazak, Fedor A1 - Schleuß, Leander A1 - Ossenbrink, Ralf A1 - Michailov, Vesselin A1 - Weiß, Sabine T1 - Particularities of testing structured sheet metals in 3-point bending tests T2 - Materials Testing N2 - Thin sheet metals from deep drawing steel DC04 are very often used in the production of car body and case parts. Quality improvement of sheet metal components by new constructive solutions (structuring) as well as adapted joining technology is going on. Structured sheet metals differ from each other by their high bending stiffness. At the same time, they show certain anisotropy due to the structure. Therefore a typical testing method of structured semi-finished parts (single sheet metals, sandwiches)is the bending test. The literature review revealed that in many studies no special demands on tests of structured materials were made. This concerns particularly the structure arrangement, structure direction and structure location of the specimen relative to the mandrel position during bending tests, i. e., the direction of the fixed load relative to the structure. The aim of this study was to determine the influence of the test specification on flexural behavior. In the present paper, honeycomb-structured sheet metals were examined using 3-point bending tests. Bending stiffness and lightweight potential were calculated with respect to the location of load application and compared for different structure arrangements,directions and locations. The influence of the anisotropy on flexural behavior of the honeycomb-patterned sheet metals was moderate. Y1 - 2016 U6 - https://doi.org/10.3139/120.110883 SN - 0025-5300 SN - 2195-8572 VL - 58 IS - 6 SP - 495 EP - 500 ER - TY - GEN A1 - Evdokimov, Anton A1 - Obrosov, Aleksei A1 - Ossenbrink, Ralf A1 - Weiß, Sabine A1 - Michailov, Vesselin T1 - Mechanical properties of dissimilar steel-aluminum weld T2 - Materials Science and Engineering: A N2 - Knowledge of the properties of dissimilar welds is of great significance for the development of multi-material lightweight structures. In this study, stainless steel (1.4301) and aluminum alloy (6082-T6) sheets were welded in overlap configuration in keyhole mode. The resulting weld metals were investigated with respect to their mechanical properties. Several samples were cut out of different locations along the welds and their cross-sections were subjected to indentation testing and energy dispersive X-ray (EDS) analysis. Young's modulus E, yield stress σy, and strain hardening exponent n, were determined by means of reverse analysis of the indentation load (P) – depth (h) curves, allowing construction of true stress – true strain relations. An essential increase in yield stress in comparison to the one of the base alloys was observed inside the weld metal. In contrary, Young's modulus and strain hardening exponent of the welds were almost identical to corresponding values of the base steel metal. Due to the sensitivity of yield stress to the aluminum content, slight variations of the welding parameters lead to significant changes in elastic-plastic behavior of the weld metal. KW - Mechanical properties KW - Indentation KW - Reverse analysis KW - EDS measurements KW - Dissimilar steel aluminum welding KW - FEM Y1 - 2018 UR - https://www.sciencedirect.com/science/article/pii/S0921509318303563 U6 - https://doi.org/https://doi.org/10.1016/j.msea.2018.03.019 SN - 0921-5093 VL - Volume 722 SP - 242 EP - 254 ER - TY - GEN A1 - Evdokimov, Anton A1 - Doynov, Nikolay A1 - Ossenbrink, Ralf A1 - Obrosov, Aleksei A1 - Weiß, Sabine A1 - Michailov, Vesselin T1 - Thermomechanical laser welding simulation of dissimilar steel-aluminum overlap joints T2 - International Journal of Mechanical Sciences N2 - Mixing of steel and aluminum within the weld pool during keyhole laser welding results in a complex dissimilar microstructure, which in turn, initiates a shift in weld metal mechanical properties. In this study, a numerical model for computation of distortions in laser-welded dissimilar overlap joints (austenitic stainless steel 304 – 6082-T6 aluminum alloy), which considers properties of the mixed steel-aluminum weld metal was developed. The required yield strength, Young's modulus, and strain hardening exponent of the weld metal were experimentally determined using the indentation technique coupled with energy-dispersive X-ray spectroscopy. The designed material model calculates the weld elastic-plastic properties as a function of the aluminum concentration. The softening of the alloys in the heat-affected zone was determined by physical simulations and considered as a function of maximum temperature. Computed and measured distortions showed good agreement for various welding regimes with an average deviation of 18.4%. The sensitivity analyses indicated that the application of the developed weld material model significantly improves the accuracy of the thermomechanical simulations. Y1 - 2021 U6 - https://doi.org/10.1016/j.ijmecsci.2020.106019 SN - 1879-2162 VL - 190 ER - TY - GEN A1 - Shapovalov, Oleg A1 - Shapovalova, Mariia A1 - Ossenbrink, Ralf A1 - Heckel, Thomas A1 - Michailov, Vesselin A1 - Weiß, Sabine A1 - Gaal, Mate T1 - Verbessern der Korrosionsbeständigkeit eines hochtemperaturbeständigen Ultraschalldämpfungskörpers mittels Laserstrahl-Auftragschweißen T2 - DVS Berichte 2021 N2 - Während in einem konventionellen Ultraschallprüfkopf ein Kunststoffdämpfungskörper mit Kleber oder Öl an einen Piezoschwinger angekoppelt ist, werden als Hochtemperaturlösung feinporöse sintermetallische Dämpfungsmaterialien mit einer Flüssigglasankopplung eingesetzt. Um dabei das Sintermetall vor dem korrosiven Angriff der Glasschmelze zu schützten, wird am Dämpfungskörper gegenwärtig Gold- oder Platinfolie zeit- und kostenaufwendig appliziert. In der aktuellen Arbeit wurde eine Methode zum Korrosionsschutz der sintermetallischen Oberfläche aus rostfreiem Stahl mittels Laser-Pulverauftragschweißen entwickelt. Im Laufe einer Schweißparameterstudie auf dem Substratmaterial aus massivem rostfreiem Stahl wurde die Eignung unterschiedlicher Auftragsmaterialien auf Nickel- und Kobaltbasis untersucht. Dabei wurde zunächst der Einfluss verschiedener Schweißparameter wie Laserleistung, Vorschubgeschwindigkeit und Pulvermenge auf die Auftragsqualität (Nahtform, Vermischungsgrad, Porosität) metallografisch bewertet. Anschließend wurden die aufgetragenen Schichten hinsichtlich ihrer Korrosionsbeständigkeit getestet. Der Kontakt mit einer flüssigen Glasmischung bei 500 °C hat bei keiner der beschichteten Proben sichtbare Korrosionswirkung gezeigt. Als Resultat der Schweißparameterstudie haben sich besonders die nickelbasierten Pulver als gut geeignete Materialien für den Prozess gezeigt. Die identifizierten Schweißparameter wurden im nächsten Schritt erfolgreich an das sintermetallische Substrat angepasst. Y1 - 2021 UR - https://www.dvs-ev.de/call4papers/abstract.cfm?vid=109&pid=7032 SN - 978-3-96144-147-1 SP - 370 EP - 377 PB - DVS Media GmbH CY - Düsseldorf ER -