TY - GEN A1 - Issayev, Gani A1 - Giri, Binod Raj A1 - Elbaz, Ayman M. A1 - Shrestha, Krishna Prasad A1 - Mauß, Fabian A1 - Roberts, William L. A1 - Farooq, Aamir T1 - Ignition delay time and laminar flame speed measurements of ammonia blended with dimethyl ether: A promising low carbon fuel blend T2 - Renewable Energy N2 - Ammonia (NH3) has recently received much attention as a promising future fuel for mobility and power generation. The use of ammonia as a fueling vector can help curb global warming by cutting CO2 emissions because it is a carbon-free fuel and a hydrogen carrier with a high percentage of hydrogen atoms per unit volume. Liquid ammonia contains a higher volumetric density of hydrogen than liquid hydrogen. The low reactivity of ammonia, however, hinders its direct usage as a combustible fuel. One feasible way to boost the reactivity of ammonia is to target a dual-fuel system comprising of ammonia and a suitable combustion promoter. In this work, combustion properties of ammonia were investigated by blending it with various proportions of dimethyl ether (DME) using a rapid compression machine (RCM) and a constant volume spherical reactor (CVSR) over a wide range of experimental conditions. DME is a highly reactive fuel that may be produced in a sustainable carbon cycle with a net zero-carbon emission. Ignition delay times (IDTs) of NH3/DME blends were measured over a temperature (T) range of 649e950 K, pressures (P) of 20 and 40 bar, equivalence ratios (F) of 0.5 and 1 for a range of DME mole fractions (cDME) of 0.05e0.5 in the blends. In addition, the laminar burning velocities of NH3/DME blends were measured at P ¼ 1, 3 and 5 bar, F ¼ 0.8e1.3 and T ¼ 300 K for cDME ranging from 0.18 to 0.47. Our results suggest that DME is a good ignition promoter, resulting in a significant shortening of IDTs and an increase of flame speeds of NH3. A detailed chemical model has been developed and validated against the experimental data. Overall, our kinetic model offered reasonable predictive capabilities capturing the experimental trends over a wide range of conditions. In the worst-case scenario, our model underpredicted IDTs by a factor of ~2.5 while overpredicting laminar flame speed by ~20%. KW - DME KW - Lamianr flame speed KW - Ignition delay time KW - Kinetic modeling KW - Ammonia Y1 - 2022 UR - https://www.sciencedirect.com/science/article/pii/S0960148121014440?via%3Dihub#! U6 - https://doi.org/10.1016/j.renene.2021.09.117 SN - 1879-0682 VL - 181 SP - 1353 EP - 1370 ER - TY - GEN A1 - Shrestha, Krishna Prasad A1 - Giri, Binod Raj A1 - Elbaz, Ayman M. A1 - Issayev, Gani A1 - Roberts, William L. A1 - Seidel, Lars A1 - Mauß, Fabian A1 - Farooq, Aamir T1 - A detailed chemical insights into the kinetics of diethyl ether enhancing ammonia combustion and the importance of NOx recycling mechanism T2 - Fuel Communications N2 - In this work, we investigated the combustion characteristics of ammonia (NH3) by blending it with various proportions of diethyl ether (DEE). We measured laminar flame speed of various NH3/DEE blends (DEE, 10–40% by mole) using a constant volume spherical vessel at Ti = 298 K and Pi = 3 and 5 bar and Φ = 0.8–1.3. We developed a detailed kinetic model to describe the trends of the current and previously published experimental data. For the robustness of the model, we first developed a comprehensive diethyl ether kinetic mechanism to accurately characterize neat DEE oxidation behavior. We validated the kinetic model using a large pool of experimental data comprising shock tube, rapid compression machine, jet-stirred and flow reactors, freely propagating, and burner-stabilized premixed flames. The developed kinetic model performs remarkably in capturing the combustion behavior of pure DEE and NH3. Importantly, our model captures the experimental data of laminar flame speed and ignition delay times of various NH3/DEE blends over a wide range of conditions. We found that DEE is a promising candidate to promote the combustion characteristics of NH3. A small portion of DEE (10%) enhances the laminar flame speed of NH3 by a factor of 2 at Pi = 1 bar, Ti = 298 K, and Φ = 1.0. A further doubling of the DEE mole fraction to 20% did not enhance the laminar flame speed of NH3 with the same propensity. At low temperatures, adding 5% DEE in NH3 blend has significantly expedited the system reactivity by lowering the autoignition temperature. A further 5% increment of DEE (i.e., 10% DEE in NH3) lowers the autoignition temperature by ∼120 K to achieve the same ignition delay time. The “NOsingle bondNO2” looping mechanism predominantly drives such reactivity accelerating effect. Here, the reactions, NO + HO2 = NO2 + OH and NO2 + H = NO + OH, appear to enhance the reactive radical pool by generating OH radicals. We observed that the HNO path is favored more with increasing DEE content which eventually liberates NO. Other key reactions in “NOsingle bondNO2” looping mechanism are: CH3 + NO2 = CH3O + NO, CH3O2 + NO = CH3O + NO2, C2H5 + NO2 = C2H5O + NO, C2H5O2 + NO = C2H5O + NO2. In addition, CH3 + NH2(+M) = CH3NH2(+M) reaction is also one of the important cross-reactions which leads to the formation of HCN. Therefore, cross-reactions between the nitrogen and carbon family are crucial in accurately predicting autoignition timing. This work provides a detailed chemical insight into the NH3 and DEE interaction, which could be applied to other fuel blends of NH3. The kinetic model is also validated for several C1single bondC3 fuels including their interaction with NOx. KW - DEE KW - Ammonia KW - Kinetic Model KW - Laminar flame speed KW - Ignition delay time Y1 - 2022 U6 - https://doi.org/10.1016/j.jfueco.2022.100051 SN - 2666-0520 VL - 10 ER - TY - GEN A1 - Rakhi, Rakhi A1 - Günther, Vivien A1 - Richter, Jana A1 - Mauß, Fabian T1 - Steam reforming of methane over nickel catalyst using a one-dimensional model T2 - International Journal of Environmental Sciences N2 - Steam reforming of hydrocarbons is a well established chemical process which provides synthesis gas (H2 and CO). These synthesis products can hence be converted to numerous valuable basic chemicals. For the industrial application of steam reforming, a detailed understanding of the process is a prerequisite. Models that capture the detailed homogeneous and heterogeneous reaction kinetics and the comprehensive transport processes as well as their interaction have the potential to optimize the catalytic process without expensive experimental campaigns. In this paper, a detailed investigation has been done using a multi-step reaction mechanism for modeling steam reforming of methane over nickel-based catalyst using a one-dimensional (1D) model, LOGEcat [1]. The model is applicable to the simulation of all standard after-treatment catalytic processes of combustion exhaust gas along with other chemical processes involving heterogeneous catalysis, such as, the Sabatier process [27]. It is a 1D tool, thus is computationally cost effective and is based on a series of perfectly stirred reactors (PSR). The model is used to perform the simulations for various reactor conditions in terms of temperature, pressure, flow rates and steam-to-carbon (S/C) ratio. Several chemical reaction terms, such as, selectivity, yield, conversion, and mole fraction have been shown with respect to the varied parameters and the results are compared with 2D simulations and experimental reference data. We report a very good agreement of the various profiles produced with 1D model as compared to the reference data. Note that the main aim of this study is to check how far the 1D model can capture the basic chemistry for modeling steam reforming of methane over nickel-based catalysts. It is interesting to note that the cost effective reduced order model is capable to capture the physics and chemistry involved with a multi-step reaction mechanism showing the predictive capability of the model. This study forms the basis for further analysis towards the thermochemistry of the species to develop a kinetically consistent reaction mechanism. Y1 - 2022 UR - https://www.iprjb.org/journals/index.php/IJES/article/view/1520/1605 U6 - https://doi.org/10.47604/ijes.1520 SN - 2519-5549 VL - 5 IS - 1 SP - 1 EP - 32 ER - TY - GEN A1 - Rakhi, Rakhi A1 - Shrestha, Krishna Prasad A1 - Günther, Vivien A1 - Mauß, Fabian T1 - Thermodynamic analysis to develop a detailed surface reaction mechanism T2 - Fuel Science - From Production to Propulsion, Aachen, Germany, May 2022 N2 - The reduction of greenhouse gasses such as CO2 and CH4 is becoming necessary due to global environmental problems. The reforming of light hydrocarbons is a particularly efficient process for producing synthesis gas, H2 and CO, from greenhouse gasses [1]. The steam reforming of methane is the most important method to produce syngas in industry by using a nickel catalyst. Nickel-based catalysts are the conventional catalysts in industrial applications due to their fast turnover rates, good availability, and low costs, however, limited by their tendency towards coke formation. In this study, a detailed surface reaction mechanism is developed for steam reform-ing of methane over nickel and results are compared with the reference data. Y1 - 2022 UR - https://www.researchgate.net/publication/361279412_Thermodynamic_analysis_to_develop_a_detailed_surface_reaction_mechanism ER - TY - GEN A1 - Picerno, Mario A1 - Lee, Sung-Yong A1 - Pasternak, Michal A1 - Siddareddy, Reddy Babu A1 - Franken, Tim A1 - Mauß, Fabian A1 - Andert, Jakob T1 - Real-Time Emission Prediction with Detailed Chemistry under Transient Conditions for Hardware-in-the-Loop Simulations T2 - Energies N2 - The increasing requirements to further reduce pollutant emissions, particularly with regard to the upcoming Euro 7 (EU7) legislation, cause further technical and economic challenges for the development of internal combustion engines. All the emission reduction technologies lead to an increasing complexity not only of the hardware, but also of the control functions to be deployed in engine control units (ECUs). Virtualization has become a necessity in the development process in order to be able to handle the increasing complexity. The virtual development and calibration of ECUs using hardware-in-the-loop (HiL) systems with accurate engine models is an effective method to achieve cost and quality targets. In particular, the selection of the best-practice engine model to fulfil accuracy and time targets is essential to success. In this context, this paper presents a physically- and chemically-based stochastic reactor model (SRM) with tabulated chemistry for the prediction of engine raw emissions for real-time (RT) applications. First, an efficient approach for a time-optimal parametrization of the models in steady-state conditions is developed. The co-simulation of both engine model domains is then established via a functional mock-up interface (FMI) and deployed to a simulation platform. Finally, the proposed RT platform demonstrates its prediction and extrapolation capabilities in transient driving scenarios. A comparative evaluation with engine test dynamometer and vehicle measurement data from worldwide harmonized light vehicles test cycle (WLTC) and real driving emissions (RDE) tests depicts the accuracy of the platform in terms of fuel consumption (within 4% deviation in the WLTC cycle) as well as NOx and soot emissions (both within 20%). KW - hardware-in-the-loop KW - virtual calibration KW - diesel powertrain KW - tabulated chemistry Y1 - 2022 U6 - https://doi.org/10.3390/en15010261 SN - 1996-1073 VL - 15 IS - 1 SP - 1 EP - 21 ER - TY - GEN A1 - Franken, Tim A1 - Srivastava, Vivek A1 - Lee, Sung-Yong A1 - Heuser, Benedikt A1 - Shrestha, Krishna Prasad A1 - Seidel, Lars A1 - Mauß, Fabian ED - Xandra, Margot ED - Payri, Raúl ED - Serrano, José Ramón T1 - Numerical Analysis of the Combustion of Diesel, Dimethyl Ether, and Polyoxymethylene Dimethyl Ethers (OMEn, n=1-3) Using Detailed Chemistry T2 - THIESEL 2022 : Conference on Thermo- and Fluid-Dynamics of Clean Propulsion Powerplants, 13th-16th September 2022 : conference proceedings N2 - New types of synthetic fuels are introduced in internal combustion engine applications to achieve carbon-neutral and ultra-low emission combustion. Dimethyl Ether (DME) and Polyoxymethylene Dimethyl Ethers (OMEn) belong to such kind of synthetic fuels. Recently, Shrestha et al. (2022) have developed a novel detailed chemistry model for OMEn (n=1-3) to predict the ignition delay time, laminar flame speed and species formation for various thermodynamic conditions. The detailed chemistry model is applied in the zero dimensional (0D) stochastic reactor model (DI-SRM) to investigate the non-premixed combustion in a 2-liter diesel engine. Further insights in the formation of unburned hydrocarbons (HC), carbon monoxide and nitrogen oxides during the combustion of OMEn fuels are obtained in this work. The combustion and emission formation of DME and OMEn (n=1-3) are investigated and compared to conventional Diesel combustion. The mixture formation is governed by an earlier vaporization of the DME and OMEn fuels, faster homogenization of the respective air-fuel mixture and higher reactivity. At the same injection pressure, the OMEn fuels obtain higher NOx but lower CO and HC emissions. High amounts of aromatics, ethene, methane formaldehyde and formic acid are found within the Diesel exhaust gas. The DME and OMEn exhaust gas contains higher fractions of formaldehyde and formic acid, and fractions of methane, methyl formate and nitromethane. KW - Polyoxymethylene Dimethyl Ethers KW - Stochastic Reactor Model KW - Detailed Chemistry KW - Modelling KW - Emissions Y1 - 2022 UR - https://www.lalibreria.upv.es/portalEd/UpvGEStore/products/p_6328-1-1 SN - 978-84-1396-055-5 U6 - https://doi.org/10.4995/Thiesel.2022.632801 PB - Editorial Universitat Politècnica de València CY - València ER - TY - GEN A1 - Franken, Tim A1 - Shrestha, Krishna Prasad A1 - Seidel, Lars A1 - Mauß, Fabian ED - Sens, Marc T1 - Effect of Gasoline–Ethanol–Water Mixtures on Auto-Ignition in a Spark Ignition Engine T2 - International Conference on Knocking in Gasoline Engines N2 - The climate protection plan of the European Union requires a significant reduction of CO2 emissions from the transportation sector by 2030. Today ethanol is already blended by 10vol-% in gasoline and further increase of the ethanol content to 20vol-% is discussed. During the ethanol production process, distillation and molecular sieving is required to remove the water concentration to achieve high-purity ethanol. However, hydrous ethanol can be beneficial to suppress knock of spark ignition engines. The hygroscopic nature of ethanol can allow to increase the water content in gasoline – water emulsions even more, without adding additional surfactants, and improve the thermal efficiency by optimized combustion phasing, while keeping the system complexity low. Hence, the effect of gasoline – ethanol – water mixtures on the auto-ignition in a single-cylinder spark ignition engine is investigated by using multi-dimensional simulation and detailed chemistry. The gasoline – ethanol mixtures are defined to keep the Research Octane Number constant, while the Motored Octane Number is decreasing. In total five surrogates are defined and investigated: E10 (10vol-% ethanol-in-gasoline), E20, E30, E70 and E100. The water content is determined according to experimentally defined ternary diagrams that evaluated stable gasoline – ethanol – water emulsion at different gasoline – ethanol blending ratios. The auto-ignition modes of the surrogates are analyzed using the diagram, which determines if hotspots are within harmless deflagration or harmful developing detonation regime. The strongest auto-ignition is observed for the E10 surrogate, while increasing ethanol content reduces the surrogate reactivity and increases the resonance parameter. No auto-ignition of the unburnt mixture is observed for the E70 and E100 surrogates. The addition of hydrous ethanol decreased the excitation time of the surrogates, especially at low ethanol content, wherefor the reactivity parameter is significantly increased. The hotspots for E10, E20 and E30 surrogates with hydrous ethanol are found within the developing detonation regime, while hotspots of the E70 surrogate with hydrous ethanol are found in the transition regime. For the hydrous E100 surrogate no auto-ignition is predicted because of reduced temperature of the unburnt mixture due to water vaporization, which outweighs the increased reactivity due to water vapor addition. KW - Knock KW - Gasoline KW - Ethanol KW - Simulation KW - Detailed Chemistry KW - Spark Ignition Y1 - 2022 SN - 978-3-8169-3544-5 U6 - https://doi.org/10.24053/9783816985440 SP - 175 EP - 222 PB - expert CY - Tübingen ER - TY - GEN A1 - Shrestha, Krishna Prasad A1 - Eckart, Sven A1 - Drost, Simon A1 - Fritsche, Chris A1 - Schießl, Robert A1 - Seidel, Lars A1 - Maas, Ulrich A1 - Krause, Hartmut A1 - Mauß, Fabian T1 - A comprehensive kinetic modeling of oxymethylene ethers (OMEn, n= 1–3) oxidation-laminar flame speed and ignition delay time measurements T2 - Combustion and Flame N2 - This work reports on the development and experimental validation of a detailed reaction mechanism for the oxidation of polyoxymethylene dimethyl ethers (OMEn, n = 1–3). The validation is done by constant-volume chamber laminar flame speeds (393 K and 443 K, 1 to 5 bar, and equivalence ratio 0.8 to 1.6) and Rapid Compression Machine ignition delay times (550–680 K, 10 and 15 bar, equivalence ratios of 0.5–2.0) in OMEn/air mixtures. Using our new experimental and published data, the validation basis for the new kinetic model comprises the pyrolysis and oxidation of OMEn (n = 1–3) in freely propagating flames, auto-ignition in rapid compression machines and shock tubes, and speciation in jet-stirred and flow reactors as well as burner-stabilized premixed flames. The model provides a reasonable agreement with the experimental data for a broad range of conditions investigated. The performance of the developed model is compared against the recent literature models. OMEn (n = 1–3) all have the same laminar flame speed. The model suggests that the chemistry of OME0 (DME) and CH3OCHO (methyl formate) is the one that dictates the flame chemistry. Under the same pressure and equivalence ratio conditions, ignition delay times of OME2 and OME3 are similar for the investigated temperature range. This work helps to improve the understanding of OMEs chemistry. The model developed in this work will serve as the base mechanism for higher chain length OMEs (n>3). Y1 - 2022 U6 - https://doi.org/10.1016/j.combustflame.2022.112426 SN - 1556-2921 SN - 0010-2180 VL - 246 ER - TY - GEN A1 - Shrestha, Krishna Prasad A1 - Elbaz, Ayman M. A1 - Giri, Binod Raj A1 - Arab, Omar Z. A1 - Adil, Mohammad A1 - Seidel, Lars A1 - Roberts, William L. A1 - Farooq, Aamir A1 - Mauß, Fabian T1 - Experimental and Kinetic Modeling Study of 1, 3-Dioxolane Oxidation and Comparison with Dimethoxymethane T2 - Energy & Fuels N2 - This work reports laminar flame speeds and ignition delay times of 1,3-dioxolane/O2/inert gases over a wide range of conditions. Laminar flame speeds were determined experimentally at pressures of 1 and 3 bar, the temperature of 300 K, and equivalence ratios ranging from 0.7 to 1.4 using a constant-volume spherical chamber, whereas ignition delay times were measured in a shock tube at a pressure of 1 bar, the temperature range of 1000–1265 K, and equivalence ratios of 0.5 and 1.0. A detailed kinetic model is developed to predict the oxidation of 1,3-dioxolane utilizing our new experimental data and published datasets on the oxidation of 1,3-dioxolane in freely propagating flames, autoignition in rapid compression machines and shock tubes, and speciation in a jet-stirred reactor. Model predictions are in reasonable agreement with the experimental data. Laminar flame speeds and ignition delay times of 1,3-dioxolane (cyclic ether) are compared with those of dimethoxymethane (acyclic ether). It is found that 1,3-dioxolane has a higher laminar flame speed than that of dimethoxymethane, which may be attributed to the formation of C2H4, C2H2, and the H atom from 1,3-dioxolane. On the contrary, ignition delay times of 1,3-dioxolane are longer than those of dimethoxymethane below 1000 K and shorter above 1000 K for the same dilution level. The reaction ȮCHO = CO2 + H is critical for accurately predicting 1,3-dioxolane oxidation, and it significantly influences model predictions under low-pressure conditions. The model developed in this work will serve as the base mechanism for higher cyclic and acyclic ethers. Y1 - 2022 U6 - https://doi.org/10.1021/acs.energyfuels.2c01132 SN - 1520-5029 SN - 0887-0624 VL - 36 IS - 14 SP - 7744 EP - 7754 ER - TY - GEN A1 - Rossi, Edoardo A1 - Bargende, Michael A1 - Kulzer, André Casal A1 - Chiodi, Marco A1 - Massoud, Ehab A1 - Shrestha, Krishna Prasad A1 - Mauß, Fabian T1 - Analysis of the applicability of Water Injection in Combination with an eFuel for Knock Mitigation and Improved Engine Efficiency T2 - SAE Technical Paper N2 - The development of future gasoline engines is dominated by the study of new technologies aimed at reducing the engine negative environmental impact and increase its thermal efficiency. One common trend is to develop smaller engines able to operate in stoichiometric conditions across the whole engine map for better efficiency, lower fuel consumption, and optimal conversion rate of the three-way catalyst (TWC). Water injection is one promising technique, as it significantly reduces the engine knock tendency and avoids fuel enrichment for exhaust temperature mitigation at high power operation. With the focus on reducing the carbon footprint of the automotive sector, another vital topic of research is the investigation of new alternative CO2-neutral fuels or so-called eFuels. Several studies have already shown how these new synthetic fuels can be produced by exploiting renewable energy sources and can significantly reduce engine emissions. This work is part of the FVV project number 1367, “Water Injection in Spark-Ignition Engines II”, which investigates the coexistence of two different engine technologies that heads towards the same direction of sustainability of the internal combustion engine: water injection and eFuels. The goal is to assess the advantages that the adoption of an eFuel in combination with water injection strategies can bring, with respect to the same strategies applied in combination with commercial gasoline. Several water injection strategies, including direct water injection, indirect water injection, injection timing, and pressure variations, are considered for a better understanding of the benefits brought by the combination of an eFuel with water injection. For this purpose, experimental tests and 3D-CFD engine simulations have been performed. The physical properties of the investigated eFuel have been experimentally measured for accurate modelling in the simulation environment, and the thermodynamic properties have been evaluated utilizing detailed chemistry calculations. Y1 - 2022 U6 - https://doi.org/10.4271/2022-37-0019 SN - 2688-3627 SN - 0148-7191 ER - TY - GEN A1 - Mante, Till A1 - Prehn, Sascha A1 - Theile, Martin A1 - Seidel, Lars A1 - Mestre, Laura A1 - Buchholz, Bert A1 - Mauß, Fabian ED - Heintzel, Alexander T1 - Investigation of An Ammonia Diesel Dual-Fuel Combustion Process on a Heavy-Duty Single Cylinder Research Engine for the Development of Suitable Simulation Tools for Maritime Applications T2 - Heavy-Duty-, On- und Off-Highway-Motoren 2022 : Stand der Energiewende im Heavy-Duty-Bereich N2 - This paper discusses the adaption of a single cylinder research engine for a retrofit application with an ammonia diesel dual-fuel combustion process and the build of an ammonia fuel system. The gaseous ammonia will be injected in the air intake pipe and the premixed ammonia air mixture will enter the combustion chamber. The diesel injection is carried out via a high-pressure common rail system. All relevant parameters can be freely adjusted via a freely programmable control unit. With the help of experimental data from a single cylinder research engine at the chair of piston machines and internal combustion engines of the University of Rostock (LKV), a dual-fuel combustion model based on detailed chemistry will be developed and optimized. This model will be integrated in a full research engine model, which ensures the best possible representation of the real engine. The combustion model is being developed by LOGE Deutschland GmbH. The full research engine model is developed by FVTR GmbH. The analysis of the combustion process starts with pure diesel operating points and is successively substituted by ammonia in the course of the measurement campaigns. Both the combustion characteristics are relevant, as they significantly influence the resulting performance and engine operation, as well as the exhaust emissions, as the carbon emissions can be reduced, but the nitrogen oxides and ammonia slip increase significantly in relevance due to the ammonia. The results obtained will be used to derive initial recommendations for action and to estimate the potential for application in the inland waterway shipping. In addition, the development of the systematic simulation tools covers a broad spectrum of research questions and aims to increase the efficiency of the necessary R&D. Y1 - 2022 SN - 978-3-658-41477-1 SN - 978-3-658-41476-4 U6 - https://doi.org/10.1007/978-3-658-41477-1_3 SP - 24 EP - 39 PB - Springer Vieweg CY - Wiesbaden ER - TY - GEN A1 - Turquand d'Auzay, Charles A1 - Shapiro, Evgeniy A1 - Prouvier, Matthieu A1 - Winkler, Axel A1 - Seidel, Lars A1 - Borg, Anders A1 - Mauß, Fabian T1 - Evaluation of Fast Detailed Kinetics Calibration Methodology for 3D CFD Simulations of Spray Combustion T2 - SAE Technical Paper N2 - Meeting strict current and future emissions legislation necessitates development of computational tools capable of predicting the behaviour of combustion and emissions with an accuracy sufficient to make correct design decisions while keeping computational cost of the simulations amenable for large-scale design space exploration. While detailed kinetics modelling is increasingly seen as a necessity for accurate simulations, the computational cost can be often prohibitive, prompting interest in simplified approaches allowing fast simulation of reduced mechanisms at coarse grid resolutions appropriate for internal combustion engine simulations in design context. In this study we present a simplified Well-stirred Reactor (WSR) implementation coupled with 3D CFD Ricardo VECTIS solver. A detailed evaluation of benchmark ECN spray problem is presented demonstrating that a single point calibration of such a model using a bulk reaction multiplier approach can provide correct representation of the solution across a wide range of temperatures on grid sizes typically employed for RANS internal combustion engine simulations with tabulated kinetics or zonal combustion models. Y1 - 2022 U6 - https://doi.org/10.4271/2022-01-1042 SN - 0148-7191 SN - 0096-5170 IS - 2022-01-1042 ER - TY - GEN A1 - Richter, Jana A1 - Günther, Vivien A1 - Mauß, Fabian T1 - Reaction mechanism development and investigation on the convergence influence in a 1D catalyst model for a γ-alumina stabilized three-way catalyst T2 - The Proceedings of the International symposium on diagnostics and modeling of combustion in internal combustion engines N2 - Accurate and computational cost-effective modeling tools for the optimization of processes and devices of all kinds are needed in nearly all scientific fields. While experimental optimization entails high expenses in terms of cost and time virtual optimization may be a promising alternative. In this work, the suitability and accuracy of a 1D heterogeneous catalytic model is investigated. First, the influence of cell discretization and residence time on the convergence in a 1D catalyst model are investigated. Second, the catalyst model is investigated and validated with use of a stoichiometric steady state three-way catalyst experiment. With the help of these investigations the reaction mechanism is further developed and new reaction rates for two reactions are presented. The modeling results are compared to a 2D simulation approach in terms of computational time and catalyst conversion behavior. The presented model is capable to capture the experimental results with a drastically reduced computational time in comparison to the 2D simulation presented in literature. Y1 - 2022 UR - https://www.jstage.jst.go.jp/article/jmsesdm/2022.10/0/2022.10_A10-3/_article/-char/en U6 - https://doi.org/10.1299/jmsesdm.2022.10.A10-3 SN - 2424-2918 ER - TY - GEN A1 - Rakhi, Rakhi A1 - Shrestha, Krishna Prasad A1 - Günther, Vivien A1 - Mauß, Fabian T1 - Kinetically consistent detailed surface reaction mechanism for steam reforming of methane over nickel catalyst T2 - Reaction Kinetics, Mechanisms and Catalysis KW - Nickel-based catalyst KW - Kinetic consistency KW - Thermodynamic analysis KW - Steam reforming KW - Detailed surface reaction mechanism Y1 - 2022 UR - https://link.springer.com/article/10.1007/s11144-022-02314-7 U6 - https://doi.org/10.1007/s11144-022-02314-7 SN - 1878-5204 SN - 1878-5190 VL - 135 IS - 6 SP - 3059 EP - 3083 ER -