TY - GEN A1 - Grönke, Martin A1 - Arrozi, Ubed S. F. A1 - Bronkalla, Nadine A1 - Schmidt, Peer A1 - Valldor, Martin A1 - Oswald, Steffen A1 - Woodcock, Thomas G. A1 - Eckert, Victoria A1 - Hao, Qi A1 - Plüschke, Laura A1 - Lederer, Albena A1 - Nielsch, Kornelius A1 - Büchner, Bernd A1 - Kaskel, Stefan A1 - Hampel, Silke T1 - Layered α-TiCl₃: Microsheets on YSZ Substrates for Ethylene Polymerization with Enhanced Activity T2 - Chemistry of Materials N2 - The transition metal halide α-titanium(III) chloride (α-TiCl₃) is a layered two-dimensional compound and a well-established Ziegler–Natta catalyst for the polymerization of ethylene. A new synthesis technique is used to obtain thin sheets of α-TiCl₃ that show exceptional physical properties in contrast to their bulk counterparts, due to an enlarged surface-to-volume ratio. Chemical vapor transport (CVT) of α-titanium(III) chloride directly on substrates results in microsheets that exhibit an improved catalytic effect. For rational planning of synthesis conditions, thermodynamic simulations of occurring gas-phase equilibria were performed. Based on these calculation results, crystal growth was achieved by adding GaCl₃via pure short term CVT in a temperature gradient of 700–600 K on yttrium-stabilized zirconia (YSZ) substrates. Phase pure, as-grown, single crystal sheets with high crystallinity and a thickness of around 4 μm were obtained. These thin sheets of α-TiCl₃ on YSZ substrates were implemented as catalysts for the ethylene polymerization reaction. A significant improvement of catalytic activity of 16% was achieved, probably due to an increased surface-to-volume ratio. As a highlight, the as-grown microsheets were exfoliated subsequently to a thickness lower than 200 nm and an even higher catalytic activity of up to 24% was confirmed experimentally due to delamination effects. This is the first time that an improved catalytic effect of α-TiCl₃ is observed as a result of downscaling from bulk to microsheets by CVT. KW - Crystal growth KW - Chemical vapor transport KW - Thermodynamic modeling KW - 2D layered compounds KW - Halides KW - Nanocrystals (1) Y1 - 2019 UR - https://pubs.acs.org/doi/10.1021/acs.chemmater.9b01818 U6 - https://doi.org/10.1021/acs.chemmater.9b01818 VL - 31 IS - 14 SP - 5305 EP - 5313 ER - TY - GEN A1 - Grönke, Martin A1 - Schmidt, Peer A1 - Valldor, Martin A1 - Oswald, Steffen A1 - Wolf, Daniel A1 - Lubk, Axel A1 - Büchner, Bernd A1 - Hampel, Silke T1 - Chemical vapor growth and delamination of α-RuCl3 nanosheets down to the monolayer limit T2 - Nanoscale N2 - 2D layered honeycomb magnet α-ruthenium(III) chloride (α-RuCl3) is a promising candidate to realize a Kitaev spin model. As alteration of physical properties on the nanoscale is additionally intended, new synthesis approaches to obtain phase pure α-RuCl3 nanocrystals have been audited. Thermodynamic simulations of occurring gas phase equilibria were performed and optimization of synthesis conditions was achieved based on calculation results. Crystal growth succeeded via chemical vapor transport (CVT) in a temperature gradient of 973 K to 773 K on YSZ substrates. Single crystal sheets of high crystallinity with heights ≤ 30 nm were obtained via pure CVT. The crystal properties were characterized by means of optical and electron microscopy, AFM, SAED, micro-Raman and XPS proving their composition, morphology, crystallinity and phase-purity. A highlight of our study is the successful individualization of nanocrystals and the delamination of nanosheets on YSZ substrates down to the monolayer limit (≤ 1 nm) which was realized by means of substrate exfoliation and ultrasonication in a very reproducible way. KW - Crystal growth KW - Thermodynamic modeling KW - Chemical vapor transport KW - 2D layered compounds KW - Nanocrystals Y1 - 2018 UR - https://pubs.rsc.org/en/content/articlelanding/2018/nr/c8nr04667k#!divAbstract U6 - https://doi.org/10.1039/C8NR04667K SN - 2040-3372 VL - 10 IS - 40 SP - 19014 EP - 19022 ER - TY - GEN A1 - Grönke, Martin A1 - Pohflepp, Danny A1 - Schmidt, Peer A1 - Valldor, Martin A1 - Oswald, Steffen A1 - Wolf, Daniel A1 - Hao, Qi A1 - Steiner, Udo A1 - Büchner, Bernd A1 - Hampel, Silke T1 - Simulation and synthesis of alpha-MoCl₃ nanosheets on substrates by short time chemical vapor transport T2 - Nano-Structures & Nano-Objects N2 - Alpha-molybdenum(III) chloride (MoCl₃) belongs to layered van-der-Waals materials, which are in focus to exhibit interesting properties due to their weak chemical and magnetic interactions. Especially the structure of alpha-MoCl₃ has been discussed in terms of symmetry breaking dimerization of Mo atoms at room temperature, which might led to exotic ground states. By exploiting the 2D materials characteristics, an investigation of physical properties on the nanoscale is intended. We herein demonstrate the probably first approach to synthesize phase pure, as-grown alpha-MoCl₃ few-layer nanosheets by means of a pure short time chemical vapor transport (CVT) process. Vapor growth benefits from a one-step deposition of high crystalline alpha-MoCl₃ nanosheets without stacking faults on a substrate. Thus, mostly applied subsequent delamination, associated with the introduction of structural defects, becomes redundant. According to the CVT process thermodynamic simulations of gas phase equilibria have been performed and the synthesis conditions could be optimized based on the calculation results. By CVT the as-grown nanolayers are deposited on sapphire (Al₂O₃) substrates by applying a temperature gradient of 70 K from 743 K to 673 K. Single crystalline sheets with thicknesses ≤75 nm down to five layer (3 nm) could be obtained by using a pure CVT process. According to the deposited nanostructures we approve the desired composition, morphology, phase purity and high crystallinity by using several microscopy and spectroscopy techniques. Furthermore, we show micro-RAMAN measurements which hint at a slight increase in phonon energies for nanosheets in comparison to the corresponding bulk phase. KW - Crystal growth KW - Chemical vapor transport KW - 2D layered compounds KW - Halides Y1 - 2019 UR - https://www.sciencedirect.com/science/article/pii/S2352507X18304888?via%3Dihub#! U6 - https://doi.org/10.1016/j.nanoso.2019.100324 SN - 2352-507X IS - 19 SP - 1 EP - 7 ER - TY - GEN A1 - Froeschke, Samuel A1 - Wolf, Daniel A1 - Hantusch, Martin A1 - Giebeler, Lars A1 - Wels, Martin A1 - Gräßler, Nico A1 - Büchner, Bernd A1 - Schmidt, Peer A1 - Hampel, Silke T1 - Synthesis of micro- and nanosheets of CrCl3–RuCl3 solid solution by chemical vapour transport T2 - Nanoscale N2 - Solid solutions of 2D transition metal trihalides are rapidly growing in interest for the search for new 2D materials with novel properties at nanoscale dimensions. In this regard, we present a synthesis method for the Cr1−xRuxCl3 solid solution and describe the behaviour of the unit cell parameters over the whole composition range, which in general follows Vegard's law in the range of a = 5.958(6)CrCl3 … 5.9731(5)RuCl3 Å, b = 10.3328(20)CrCl3 … 10.34606(21)RuCl3 Å, c = 6.110(5)CrCl3 … 6.0385(5)RuCl3 Å and β = 108.522(15)CrCl3 … 108.8314(14)RuCl3 °. The synthesized solid solution powder was subsequently used to deposit micro- and nanosheets directly on a substrate by applying chemical vapour transport in a temperature gradient of 575 °C → 525 °C for 2 h and 650 °C → 600 °C for 0.5 h as a bottom-up approach without the need for an external transport agent. The observed chromium chloride enrichment of the deposited crystals is predicted by thermodynamic simulation. The results allow for a nanostructure synthesis of this solid solution with a predictable composition down to about 30 nm in height and lateral size of several μm. When applying a quick consecutive delamination step, it is possible to obtain few- and monolayer structures, which could be used for further studies of downscaling effects for the CrCl3–RuCl3 solid solution. X-ray photoelectron spectroscopy, transmission electron microscopy and Raman spectroscopy were used to confirm the purity and quality of the synthesized crystals. KW - Crystal growth KW - Chemical vapor transport KW - Thermal analysis KW - Thermodynamic modeling KW - 2D layered compounds Y1 - 2022 UR - https://pubs.rsc.org/en/content/articlelanding/2022/NR/D2NR01366E U6 - https://doi.org/10.1039/D2NR01366E SN - 2040-3372 VL - 29 IS - 14 SP - 10483 EP - 10492 ER - TY - GEN A1 - Grönke, Martin A1 - Buschbeck, Benjamin A1 - Schmidt, Peer A1 - Valldor, Martin A1 - Oswald, Steffen A1 - Hao, Qi A1 - Lubk, Axel A1 - Wolf, Daniel A1 - Steiner, Udo A1 - Büchner, Bernd A1 - Hampel, Silke T1 - Chromium Trihalides CrX₃(X = Cl, Br, I): Direct Deposition of Micro‐ and Nanosheets on Substrates by Chemical Vapor Transport T2 - Advanced Materials Interfaces N2 - The experimental observation of intrinsic ferromagnetism in single layered chromium trihalides CrX₃ (X = Cl, Br, I) has gained outstanding attention recently due to their possible implementation in spintronic devices. However, the reproducible preparation of highly crystalline chromium(III) halide nanolayers without stacking faults is still an experimental challenge. As chromium trihalides consist of adjacent layers with weak interlayer coupling, the preparation of ultrathin CrX₃ nanosheets directly on substrates via vapor transport proves as an advantageous synthesis technique. It is demonstrated that vapor growth of ultrathin highly crystalline CrX₃ micro‐ and nanosheets succeeds directly on yttrium stabilized zirconia substrates in a one‐step process via chemical vapor transport (CVT) in temperature gradients of 100 K (600°C → 500°C for CrCl₃ and 650°C → 550°C for CrBr₃ or CrI₃) without a need for subsequent delamination. Due to simulation results, optimization of synthesis conditions is realized and phase pure CrX₃ nanosheets with thicknesses ≤25 nm are obtained via short term CVT. The nanosheets morphology, crystallinity, and phase purity are analyzed by several techniques, including microscopy, diffraction, and spectroscopy. Furthermore, a potential subsequent delamination technique is demonstrated to give fast access to CrX₃ monolayers using the example of CrCl₃ . KW - 2D layered compounds KW - Crystal growth KW - Chemical vapor transport KW - Halides KW - Nanocrystals KW - Thermodynamic modeling Y1 - 2019 UR - https://onlinelibrary.wiley.com/doi/epdf/10.1002/admi.201901410 U6 - https://doi.org/10.1002/admi.201901410 SN - 2196-7350 VL - 6 IS - 24 ER - TY - GEN A1 - Martin, Bernd A1 - Süß, Hendrik T1 - Milnor algebras could be isomorphic to modular algebras Y1 - 2009 ER - TY - GEN A1 - Martin, Bernd A1 - Lavandoskyy, Victor T1 - A Symbolic Approach to Generation and Analysis of Finite Difference Schemes of Partial Differential Equations T2 - arXiv.org : (math-ph) KW - Computer Algebra KW - Differential Equation KW - Difference Schemes Y1 - 2010 UR - http://arxiv.org/pdf/1007.4443.pdf ER - TY - GEN A1 - Martin, Bernd A1 - Hirsch, Tobias T1 - Deformation with sections: Cotangent cohomology, flatnes conditions and modular germs T2 - arXiv.org : (math.CV) Y1 - 2003 UR - http://arxiv.org/pdf/math/0306281v1.pdf ER - TY - CHAP A1 - Jantke, Klaus-Peter A1 - Memmel, Martin A1 - Rostanin, Oleg A1 - Thalheim, Bernhard A1 - Tschiedel, Bernd ED - Eder, Johann T1 - Decision Support by Learning-on-Demand T2 - The 15th Conference on Advanced Information Systems Engineering (CAiSE '03), Klagenfurt/Velden, Austria, 16-20 June, 2003, workshops proceedings KW - decision support Y1 - 2003 SN - 86-435-0552-8 SP - 317 EP - 328 PB - Techn. Univ. CY - Aachen ER - TY - GEN A1 - Kühhorn, Arnold A1 - Beirow, Bernd A1 - Schrape, Sven A1 - Golze, Mark A1 - Knöpke, Martin T1 - Simulation fluidgedämpfter Strukturschwingungen mittels partitionierter Fluid-Struktur-Kopplung T2 - Forum der Forschung Y1 - 2005 SN - 0947-6989 VL - 9 IS - 18 SP - 79 EP - 86 ER - TY - CHAP A1 - Martin, Bernd A1 - Hirsch, Tobias T1 - Modular Strata of Deformation Functors T2 - Computational commutative and non-commutative algebraic geometry, proceedings of the Nato Advanced Research Workshop on Computational Commutative and Non-Commutative Algebraic Geometry, Chisinau, Moldova, 6 - 11 June 2004 Y1 - 2005 SN - 1-586-03505-3 SP - 156 EP - 166 PB - IOS Press CY - Amsterdam [u.a.] ER - TY - GEN A1 - Martin, Bernd A1 - Pochekutov, Dimitry T1 - Discriminant and Singularities of Logarithmic Gauss Map, Examples and Application T2 - Journal of Siberian Federal University, Mathematik & Physics N2 - The study of hypersurfaces in a torus leads to the beautiful zoo of amoebas and their contours, whose possible configurations are seen from combinatorial data. There is a deep connection to the logarithmic Gauss map and its critical points. The theory has a lot of applications in many directions. In this report we recall basic notions and results from the theory of amoebas, show some connection to algebraic singularity theory and discuss some consequences from the well known classification of singularities to this subject. Moreover, we have tried to compute some examples using the computer algebra system SINGULAR and discuss different possibilities and their effectivity to compute the critical points. Here we meet an essential obstacle: Relevant examples need real or even rational solutions, which are found only by chance. We have tried to unify different views to that subject. KW - logarithmic Gauss map, singularities, discriminant, asymptotics, hypersurface amoeba Y1 - 2013 SN - 1997-1397 VL - 6 IS - 1 SP - 74 EP - 85 ER - TY - GEN A1 - Viehweger, Bernd A1 - Schölzke, Thomas A1 - Schierz, Martin T1 - Drücken strukturierter Feinbleche T2 - Bänder, Bleche, Rohre : bbr KW - strukturierte Feinbleche Y1 - 2013 UR - www.bbr.de VL - 54 IS - 6 SP - 122 EP - 123 ER - TY - GEN A1 - Steffens, S. A1 - Becker, C. A1 - Amkreutz, Daniel A1 - Klossek, André A1 - Kittler, Martin A1 - Chen, Y.-Y. A1 - Schnegg, Alexander A1 - Klingsporn, Max A1 - Abou-Ras, Daniel A1 - Lips, Klaus A1 - Rech, Bernd T1 - Impact of Dislocations and Dangling Bond Defects on The Electrical Performance of Crystalline Silicon Thin Films T2 - Applied Physics Letters Y1 - 2014 U6 - https://doi.org/10.1063/1.4890625 SN - 1077-3118 SN - 0003-6951 VL - 105 IS - 2 SP - 022108 ER - TY - GEN A1 - Klossek, Andre A1 - Mankovics, Daniel A1 - Arguirov, Tzanimir V. A1 - Ratzke, Markus A1 - Kirner, Simon A1 - Friedrich, Felice A1 - Gabriel, Onno A1 - Stannowski, Bernd A1 - Schlatmann, Rutger A1 - Kittler, Martin T1 - Growth process of microcrystalline silicon studied by combined photoluminsescence and Raman investigations T2 - Journal of applied physics Y1 - 2013 U6 - https://doi.org/10.1063/1.4838058 SN - 1520-8850 VL - 114 SP - 223511 ER - TY - CHAP A1 - Lips, Klaus A1 - Schulze, Tim F. A1 - Starr, David E. A1 - Bär, Marcus A1 - Wilks, Regan G. A1 - Fenske, F. A1 - Ruske, Florian A1 - Reiche, Martin A1 - Krol, Roel van de A1 - Reichardt, Gerd A1 - Schäfers, Franz A1 - Hendel, Stefan A1 - Follath, Rolf A1 - Bahrdt, Johannes A1 - Peredkov, Sergey A1 - DeBeer, Serena A1 - Hävecker, Michael A1 - Knop-Gericke, Axel A1 - Rau, Björn A1 - Kaufmann, Christian A1 - Schlatmann, Rutger A1 - Schlögl, Robert A1 - Rech, Bernd A1 - Raoux, Simone T1 - EMIL: The Energy Materials In-situ Laboratory Berlin – A novel characterization facility for photovoltaic and energy materials T2 - 31st European Photovoltaic Solar Energy Conference and Exhibition, proceedings of the international conference held in Hamburg, Germany, 14 -18 September 2015 Y1 - 2015 SN - 3-936338-39-6 U6 - https://doi.org/10.4229/EUPVSEC20152015-1AO.2.1 SP - 25 EP - 28 PB - WIP CY - München ER - TY - RPRT A1 - Böttger, Stefan A1 - Felgentreff, Bernd A1 - Hesse, Gerold A1 - Hloucal, Martin-Joseph A1 - Leßmann, Dieter A1 - Mix, Sebastian A1 - Roselt, Kersten A1 - Safarik, Mathias A1 - Schmidt, Jörg A1 - Steffan, Christoph A1 - Uhlmann, Wilfried T1 - Seethermie - Innovative Wärmeversorgung aus Tagebaurestseen - Schlussbericht KW - Seethermie Y1 - 2021 UR - https://www.innovationsregion-mitteldeutschland.com/wp-content/uploads/2021/07/20210723_Schlussbericht-Seethermie_Langfassung.pdf CY - Leipzig ER - TY - RPRT A1 - Salecki, Steven A1 - Heinbach, Katharina A1 - Hirschl, Bernd A1 - Weidinger, Roman A1 - Schäfer-Stradowsky, Simon A1 - Ott, Ralf A1 - Lehnert, Wieland A1 - Kliem, Christine A1 - Altrock, Martin A1 - Umlauf, Florian A1 - Puffe, Matthias T1 - Finanzielle Beteiligung von betroffenen Kommunen bei Planung, Bau und Betrieb von erneuerbaren Energieanlagen (FinBEE) Ergebnisse für die Windenergie N2 - Im vorliegenden Bericht wurden die in Wissenschaft und Praxis diskutierten Instrumente zur finanziellen Beteiligung von Kommunen an EE-Anlagen vertieft analysiert und insbesondere rechtlich geprüft. Dabei kann unterschieden werden zwischen Instrumenten, die an bestehende Abgabenzahlungen an Kommunen anknüpfen (Grundsteuer, Gewerbesteuer, Konzessionsabgabe), und Instrumenten, mit denen eine neue Abgabe zugunsten der Kommune geschaffen wird (Sonderabgabe, Außenbereichsabgabe). Auf der Basis dieser Analyse wurde dann ein eigenes Instrument entwickelt (EEG-integrierter Mechanismus) sowie Ausgestaltungsempfehlungen zur Umsetzung. Neben den Instrumenten zur finanziellen Beteiligung von Kommunen wurde aufgrund der politischen Entwicklungen im Laufe des Forschungsvorhabens zusätzlich das Angebot vergünstigter (Bürger-)Stromtarife als ein Instrument zur Bürgerbeteiligung untersucht und ebenfalls mit Ausgestaltungsvorschlägen empfohlen. Y1 - 2020 UR - https://www.ioew.de/fileadmin/user_upload/BILDER_und_Downloaddateien/Publikationen/2020/FinBEE_Bericht_WEA_09092020.pdf PB - Studie im Auftrag des Bundesministeriums für Wirtschaft und Energie (BMWi) CY - Berlin ER - TY - RPRT A1 - Salecki, Steven A1 - Hirschl, Bernd A1 - Lehnert, Wieland A1 - Altrock, Martin A1 - Kliem, Christine A1 - Weidinger, Roman A1 - Schäfer-Stradowsky, Simon A1 - Ott, Ralf T1 - Finanzielle Beteiligung von betroffenen Kommunen bei Planung, Bau und Betrieb von erneuerbaren Energieanlagen. Kurzpapier mit Empfehlungen zur kommunalen und Bürgerbeteiligung an Windenergieanlagen. N2 - Das vorliegende Papier präsentiert die von den Gutachter/innen erarbeiteten Vorschläge zur finanziellen Beteiligung von Kommunen und BürgerInnen an lokalen Onshore-Windenergieanlagen (WEA). Die beiden empfohlenen kommunalen und Bürgerbeteiligungsinstrumente wurden im Projektverlauf nach mehreren Kriterien ausgewählt. Ein kommunales Beteiligungsinstrument, das über das EEG finanziert wird, behebt die verfassungs- und finanzverfassungsrechtlichen Probleme, die andere vorgeschlagene Steuer- und Abgabeninstrumente mit sich bringen. Eine privatrechtliche Zahlungsvereinbarung wurde daher im Rahmen unserer umfangreichen Bewertung als vorzugswürdig erachtet und wird hier weiter hinsichtlich eines konkreten Umsetzungsvorschlags ausgearbeitet. Als direktes Bürgerbeteiligungsinstrument werden vergünstigte Bürgerstromtarife vorgestellt. Auf Empfehlung des Vermittlungsausschusses des Bundestags und Bundesrats und vor dem Hintergrund der hohen Zustimmungswerte der Bevölkerung zu diesem Instrument, werden vergünstigte Bürgerstromtarife als Bürgerbeteiligungsinstrument zur Implementierung neben einem kommunalen Beteiligungsinstrument empfohlen – direkt verknüpft mit der kommunalen Beteiligung. Beide Vorschläge führen insgesamt zu jährlichen Zahlungen an die betroffenen Kommunen und Bürger/innen im Bereich von 20.000 bis 30.000 Euro pro WEA. Dabei wird dem WEA-Betreiber ermöglicht, alternativ die Zahlungen ausschließlich an die Kommune zu entrichten. Y1 - 2020 UR - https://www.ioew.de/fileadmin/user_upload/BILDER_und_Downloaddateien/Publikationen/2020/IOEW__BBH_und_IKEM__2020__-_Finanzielle_Beteiligung_von_Kommunen_an_EE-An....pdf CY - Berlin ER - TY - GEN A1 - Froeschke, Samuel A1 - Yasmen, Nadia A1 - Popov, Alexey A1 - Schiemenz, Sandra A1 - Wolf, Daniel A1 - Giebeler, Lars A1 - Hantusch, Martin A1 - Gräßler, Nico A1 - Büchner, Bernd A1 - Schmidt, Peer A1 - Hampel, Silke T1 - Controlled Nanoplatelet Deposition of 2D Chromium Trihalide Solid Solutions T2 - Chemistry of Materials N2 - The two-dimensional (2D) chromium trihalides CrCl3, CrBr3, and CrI3 are most famous for their exotic magnetic properties when their crystals get downscaled to nanometer dimensions. One way to tune the properties of such materials and to further increase their potential utility, e.g., in spintronics, is the formation of solid solutions. Here, we present a detailed theoretical and experimental study on the synthesis and nanoplatelet growth of CrBrxCl3–x and CrBrxI3–x solid solutions. Phase pure powder was obtained by tempering the respective parent compounds at 600 and 550 °C, using additional iodine in the case of CrBrxI3–x. The dominant stacking order changes at x = 1.8 for CrBrxCl3–x while remaining similar to CrI3 for the whole CrBrxI3–x series. A consecutive chemical vapor transport from 575 → 525 °C for 2 h (CrBrxCl3–x) or 600 → 550 °C for 3 h with 0.1 mmol additional iodine (CrBrxI3–x) resulted in the deposition of high-quality nanoplatelets on a substrate with only several nanometers in height. The composition can be controlled by the choice of the starting material, since only small shifts in the anion ratio occur during the transport. The deposited CrBrxCl3–x nanoplatelets can then be easily delaminated by ultrasonication in ethanol to reduce the height even further to few-layer dimensions. These nanoplatelets could potentially be used to investigate the property changes (e.g., in terms of magnetic response) for the downscaling of these solid solutions. We further demonstrate the quality of the deposited material by transmission electron microscopy, selected area electron diffraction, and X-ray photoelectron spectroscopy. Raman spectroscopy of the solid solution series reveals a complex evolution of vibrational modes. Photoluminescence measurements on solid solution samples show emission peaks in the near-infrared energy range with the specific energy and intensity being composition and temperature dependent. KW - 2D layered compounds KW - Chemical vapor transport KW - Crystal growth KW - Crystal structure KW - Halides KW - Thermodynamic modeling Y1 - 2023 UR - https://pubs.acs.org/doi/full/10.1021/acs.chemmater.2c03785 U6 - https://doi.org/10.1021/acs.chemmater.2c03785 SN - 1520-5002 SN - 0897-4756 VL - 35 IS - 11 SP - 4136 EP - 4148 ER - TY - RPRT A1 - Hirschl, Bernd A1 - Hoffmann, Esther A1 - Gebauer, Jana A1 - Dunkelberg, Elisa A1 - Hirschfeld, Jesko A1 - Rotter, Maja A1 - Stegnitz, Antje A1 - Wurbs, Sven A1 - Lotz, Wiebke A1 - Welp, Martin T1 - Stakeholder-Dialoge - Chancen und Risiken des Klimawandels N2 - Der Klimawandel zeigt bereits heute Folgen, die sich je nach Region unterschiedlich auswirken und für Unternehmen und Sektoren sowohl mit Risiken als auch mit Chancen verbunden sein können. Um Bedarfe und Strategien für entsprechende Anpassungsmaßnahmen zu identifizieren, führte das IÖW im Auftrag des Kompetenzzentrums Klimafolgen und Anpassung im Umweltbundesamt (KomPass) gemeinsam mit der Hochschule für Nachhaltige Entwicklung Eberswalde 2009 und 2010 sechs Fachdialoge zu den Bereichen Bevölkerungsschutz, Chemieindustrie, Küstenschutz, Verkehrsinfrastruktur, Energie- und Versicherungswirtschaft durch. Die Dialogreihe fand ihren Abschluss in der sektorenübergreifenden Konferenz „Schon angepasst?“. Die Veranstaltungen waren Teil des Forschungsvorhabens „Stakeholder-Dialoge: Chancen und Risiken des Klimawandels.“ Der Abschlussbericht zum Projekt enthält neben einer Gesamtauswertung zu den Inhalten und Methoden auch die Ergebnisse und Dokumentationen aller Einzelveranstaltungen. KW - Klimaschutz KW - Umwelt Y1 - 2011 UR - https://www.umweltbundesamt.de/sites/default/files/medien/461/publikationen/4071.pdf PB - Umweltbundesamt (UBA) CY - Dessau-Roßlau ER - TY - RPRT A1 - Hirschl, Bernd A1 - Reusswig, Fritz A1 - Weiß, Julika A1 - Bölling, Lars A1 - Bost, Mark A1 - Flecken, Ursula A1 - Haag, Leilah A1 - Heiduk, Philipp A1 - Klemm, Patrick A1 - Lange, Christoph A1 - Lass, Wiebke A1 - Richter, Paul-Martin A1 - Rupp, Johannes A1 - Salecki, Steven A1 - Schwarz, Uwe A1 - Weyer, Gregor A1 - Voigt, Rainer T1 - Entwurf für ein Berliner Energie - und Klimaschutzprogramm (BEK), Endbericht, November 2015 N2 - Der Berliner Senat hat sich zum Ziel gesetzt bis 2050 klimaneutral zu werden. Das IÖW war bereits an der Machbarkeitsstudie „Klimaneutrales Berlin 2050“ beteiligt. Darauf aufbauend wurde nun das Berliner Energie- und Klimaschutzprogramm entwickelt. Unter der Gesamtprojektleitung des IÖW wurden hierfür gemeinsam mit sieben Partnerinstitutionen konkrete Strategien für die Handlungsfelder Energieversorgung, Gebäude und Stadtentwicklung, Wirtschaft, private Haushalte und Konsum sowie Verkehr erarbeitet. Das Projekt zeichnet sich durch einen breit angelegten Beteiligungsprozess aus, in den sowohl ausgewählte Akteure der Fachöffentlichkeit im Rahmen von Workshops, als auch die breite Öffentlichkeit, hauptsächlich in Form eines Online-Dialoges, miteingebunden werden. Der Entwurf wurde im Auftrag der Senatsverwaltung für Stadtentwicklung und Umwelt durch ein vom IÖW geführtes Projektteam im Rahmen einer etwa einjährigen Bearbeitungszeit unter Einbeziehung der Berliner Stadtgesellschaft erarbeitet. Er dient als Vorlage für ein vom Senat zu verabschiedendes Programm, welches nach Vorgabe und zur Ergänzung des geplanten Berliner Energiewendegesetzes (EWG Bln) zu erstellen ist. Bei der hier vorliegenden Veröffentlichung handelt es sich um den Endbericht dieses BEK-Entwurfs, der sämtliche Maßnahmenvorschläge und deren Bewertung beinhaltet. KW - Berlin KW - Stadtentwicklung KW - Energiepolitik KW - Klimaschutz Y1 - 2015 UR - http://www.stadtentwicklung.berlin.de/umwelt/klimaschutz/bek_berlin/download/BEK-Endbericht-und-AnhangA.pdf CY - Berlin ER - TY - BOOK A1 - Hirschl, Bernd A1 - Hoffmann, Esther A1 - Zapfel, Björn A1 - Hoppe-Klipper, Martin A1 - Durstewitz, Michael A1 - Bard, Jochen T1 - Markt- und Kostenentwicklung erneuerbarer Energien. 2 Jahre EEG - Bilanz und Ausblick N2 - Die Einführung des Erneuerbare-Energien-Gesetzes (EEG) im Jahr 2000 hat in Deutschland zu einem deutlichen Anstieg der Stromerzeugung aus erneuerbaren Energien geführt. Doch wie sind die Markt- und Kostenentwicklungen der einzelnen erneuerbaren Energietechnologien genau verlaufen? Wie teuer sind regenerativ erzeugte Kilowattstunden tatsächlich? Antworten auf diese Fragen gibt das Gutachten zur Markt- und Kostenentwicklung erneuerbarer Energien, das im Erich-Schmidt-Verlag erschienen ist. Das Gutachten beinhaltet eine Gesamtschau zentraler Kenngrößen, Informationen zur technologischen Weiterentwicklung in der näheren Zukunft sowie eine differenzierte Aufschlüsselung der Kosten regenerativen Stroms. Es umfasst Einzelberichte zur Photovoltaik, Bioenergie, Windenergie, Wasserkraft, Geothermie und zum „grünen Strom“. Das Gutachten wurde im Auftrag des Bundesministeriums für Wirtschaft und Technologie vom Institut für ökologische Wirtschaftsforschung (IÖW) federführend und in Kooperation mit dem Institut für Solare Energietechnik (ISET) erstellt. Die Ergebnisse sind in den ersten Erfahrungsbericht zum EEG an den Deutschen Bundestag (Mitte 2002) eingeflossen. Sie basieren auf Erhebungen und Analysen, die 2001 und 2002 unter Beteiligung vieler Branchenakteure durchgeführt wurden. KW - Erneuerbare-Energien-Gesetz Y1 - 2002 SN - 3-503-07020-6 PB - Erich Schmidt Verlag CY - Berlin ER - TY - RPRT A1 - Hirschl, Bernd A1 - Reusswig, Fritz A1 - Weiß, Julika A1 - Bölling, Lars A1 - Bost, Mark A1 - Flecken, Ursula A1 - Haag, Leilah A1 - Heiduk, Philipp A1 - Klemm, Patrick A1 - Lange, Christoph A1 - Lass, Wiebke A1 - Richter, Paul-Martin A1 - Rupp, Johannes A1 - Salecki, Steven A1 - Schwarz, Uwe A1 - Weyer, Gregor A1 - Voigt, Rainer T1 - Entwurf für ein Berliner Energie- und Klimaschutzprogramm (BEK) - Technischer Anhang B N2 - Der Berliner Senat hat sich zum Ziel gesetzt bis 2050 klimaneutral zu werden. Das IÖW war in diesem Zuge bereits an der Machbarkeitsstudie „Klimaneutrales Berlon 2050“ beteiligt. Darauf aufbauend wurde nun das Berliner Energie- und Klimaschutzprogramm entwickelt. Unter der Gesamtprojektleitung des IÖW wurden hierfür gemeinsam mit sieben Partnerinstitutionen konkrete Strategien für die Handlungsfelder Energieversorgung, Gebäude und Stadtentwicklung, Wirtschaft, private Haushalte und Konsum sowie Verkehr erarbeitet. Das Projekt zeichnet sich durch einen breit angelegten Beteiligungsprozess aus, in den sowohl ausgewählte Akteure der Fachöffentlichkeit im Rahmen von Workshops, als auch die breite Öffentlichkeit, hauptsächlich in Form eines Online-Dialoges, miteingebunden werden. Der Entwurf wurde im Auftrag der Senatsverwaltung für Stadtentwicklung und Umwelt durch ein vom IÖW geführtes Projektteam im Rahmen einer etwa einjährigen Bearbeitungszeit unter Einbeziehung der Berliner Stadtgesellschaft erarbeitet. Er dient als Vorlage für ein vom Senat zu verabschiedendes Programm, welches nach Vorgabe und zur Ergänzung des geplanten Berliner Energiewendegesetzes (EWG Bln) zu erstellen ist. Der technische Anhang bietet einen zusätzlichen Einblick in die methodische Herangehensweise als Ergänzung zum Hauptbericht und Anhang A. KW - Berlin KW - Stadtentwicklung KW - Energiepolitik KW - Klimaschutz Y1 - 2015 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:101:1-201601205042 UR - https://www.ioew.de/fileadmin/user_upload/BILDER_und_Downloaddateien/Publikationen/2016/Hirschl_Bernd_Entwurf_für_ein_Berliner_Energie-_und_Klimaschutzprogramm__BEK_-technischer_Anhang.pdf PB - Senatsverwaltung für Stadtentwicklung und Umwelt CY - Berlin ER - TY - GEN A1 - Thrän, Daniela A1 - Bauschmann, Martin A1 - Dahmen, Nicolaus A1 - Erlach, Berit A1 - Heinbach, Katharina A1 - Hirschl, Bernd A1 - Hildebrand, Jan A1 - Rau, Irina A1 - Majer, Stefan A1 - Oehmichen, Katja A1 - Schweizer-Ries, Petra A1 - Hennig, Christiane T1 - Bioenergy beyond the German “Energiewende” Assessment framework for integrated bioenergy strategies T2 - Biomass and Bioenergy N2 - Um die nationalen Klimaschutzziele zu erreichen, ist eine grundlegende Transformation des Energiesystems erforderlich. In diesem Zusammenhang stellt sich auch die Frage, wie eine Transformation der heutigen Bioenergie-Wertschöpfungsketten aussehen muss, um einen Beitrag zu emissionsarmen Energie- und Versorgungssystemen im Jahr 2050 leisten zu können. Dabei sind nicht nur ökonomische, ökologische und soziale Aspekte zu berücksichtigen. Auch der technologische Reifegrad, eine größere Flexibilität bei Energieerzeugung und -versorgung sowie die Möglichkeit, die Technologien mit CO2-Abscheidung zu kombinieren, sind wichtige Faktoren für zukünftige Bioenergiesysteme. Mithilfe einer hierfür entwickelten und insgesamt 29 Kriterien umfassenden Bewertungsmatrix wurden mehrere Bioenergietechnologie-Optionen bewertet. Im Ergebnis zeigen sich deutlich größere Hürden mit Blick auf die Transformation und Umsetzung beim Entwicklungspfad Lignozellulose im Vergleich zum Biogaspfad (feuchte Biomasse). Trade-Offs zwischen den Bewertungskriterien werden mittels einem Ampelschema sichtbar gemacht. Die Ergebnisse können politische Entscheidungsträger dabei unterstützen, eine langfristige Bioenergiestrategie zu entwickeln und in die Umsetzung zu bringen und damit einen Beitrag zu einer erfolgreichen Transformation hin zu einem nachhaltigen Energiesystem im Jahr 2050 leisten. KW - biomass, bioenergy, energiewende Y1 - 2020 U6 - https://doi.org/10.1016/j.biombioe.2020.105769 SN - 0961-9534 VL - Vol. 142 ER - TY - CHAP A1 - Martin, Bernd T1 - Computing versal deformations with SINGULAR Y1 - 1999 ER - TY - CHAP A1 - Martin, Bernd T1 - Modular lines for singularities of the T-seris KW - Unimodal Singularities KW - Deformations of singularities KW - Modulatity Y1 - 2007 ER - TY - GEN A1 - Henke, Anna-Sophia A1 - Noack, Martin A1 - Geyer, Thomas A1 - Heinrich, Christoph Rocky A1 - Beirow, Bernd A1 - Sarradj, Ennes A1 - Kühhorn, Arnold T1 - Calculation of the Modal Behavior of Structured Sheet Metal T2 - International Journal of Lightweight Materials and Manufacture Y1 - 2019 U6 - https://doi.org/10.1016/j.ijlmm.2019.01.004 SN - 2588-8404 ER - TY - JOUR A1 - Martin, Bernd A1 - Grassmann, H. A1 - Greuel, G.-M. A1 - Neumann, W. A1 - Pfister, Gerhard A1 - Pohl, W. A1 - Schönemann, H. A1 - Siebert, Thomas T1 - On an implementation of standard bases and syzygies in SINGULAR Y1 - 1996 ER - TY - JOUR A1 - Martin, Bernd A1 - Hirsch, Tobias T1 - Deformations with section: Cotangent cohomology, flatness and modular subspaces Y1 - 2006 ER - TY - JOUR A1 - Martin, Bernd A1 - Aleksandrov, Aleksandr T1 - Gauss-Manin connection associated with bouquets of curves Y1 - 2003 ER - TY - JOUR A1 - Martin, Bernd A1 - Süß, Hendrik T1 - Milnor algebras versus modular germs for unimodal hypersurface singularities KW - Hypersurface singularities KW - Milnor algebras KW - modular deformations KW - flatness strata Y1 - 2007 ER - TY - JOUR A1 - Martin, Bernd A1 - Pfister, Gerhard A1 - Popescu, Dorin T1 - Maximal Cohen-Macaulay modules over rings of type xt+y3 Y1 - 1997 ER - TY - JOUR A1 - Martin, Bernd A1 - Siebert, Thomas T1 - Graded Lie algebras and quasihomogeneous complete intersection singularities Y1 - 1996 ER - TY - JOUR A1 - Martin, Bernd A1 - Aleksandrov, Aleksandr T1 - Derivations and deformations of artinian algebras Y1 - 1992 ER - TY - JOUR A1 - Martin, Bernd T1 - Coarse moduli space of ordinary multiple points in the plane Y1 - 1993 ER - TY - JOUR A1 - Martin, Bernd T1 - Modular deformations and space curve singularities KW - versal deformations KW - curve singularities KW - local moduli Y1 - 2003 ER - TY - JOUR A1 - Martin, Bernd A1 - Aleksandrov, Aleksandr T1 - Gauss-Manin connection for bouquets of curves Y1 - 2002 ER - TY - JOUR A1 - Martin, Bernd T1 - Svijasanost Gaussa-Manina dlja buketov krivich Y1 - 2002 ER - TY - JOUR A1 - Martin, Bernd T1 - Algorithmic Computation of Flattenings and of Modular Deformations Y1 - 2002 PB - Elsevier ER - TY - RPRT A1 - Martin, Bernd A1 - Palamodov, Victor P. T1 - Discrete and modular deformations of singularities, applications Y1 - 2004 PB - BTU, Institut für Mathematik CY - Cottbus ER - TY - RPRT A1 - Martin, Bernd A1 - Siebert, Thomas T1 - Splitting algorithm for vector bundles Y1 - 1997 PB - Univ. CY - Kaiserslautern ER - TY - GEN A1 - Lützner, Jörg A1 - Deckert, Stefanie A1 - Lange, Toni A1 - Postler, Anne Elisabeth A1 - Aringer, Martin A1 - Berth, Hendrik A1 - Bork, Hartmut A1 - Dreinhöfer, Karsten E A1 - Günther, Klaus-Peter A1 - Heller, Karl-Dieter A1 - Hube, Robert A1 - Kirschner, Stephan A1 - Kladny, Bernd A1 - Kopkow, Christian A1 - Sabatowski, Rainer A1 - Stoeve, Johannes A1 - Wagner, Richard A1 - Lützner, Cornelia T1 - Evidenzbasierte und patientenorientierte Indikationsstellung zur Knieendoprothese – Update der Leitlinie T2 - Zeitschrift für Orthopädie und Unfallchirurgie N2 - ZusammenfassungDie Implantation einer Knieendoprothese zählt mit ca. 170000 Eingriffen pro Jahr zu den am häufigsten stationär durchgeführten Operationen in Deutschland. Eine einheitliche, angemessene und patientenorientierte ärztliche Indikationsstellung ist bei einem solchen Eingriff unerlässlich. Das Update der S2k-Leitlinie „Indikation Knieendoprothese“ beinhaltet auf aktueller Evidenz basierende und im breiten Konsens abgestimmte Empfehlungen und eine Checkliste im praxistauglichen Format.Für dieses Leitlinien-Update wurde eine systematische Literaturrecherche nach (inter-)nationalen Leitlinien und systematischen Übersichtsarbeiten zur Gonarthrose und Knieendoprothetik durchgeführt, um klinisch relevante Fragestellungen zu Diagnostik, Prädiktoren für das Outcome, Risikofaktoren und Kontraindikatoren zu beantworten.Eine Knieendoprothese soll nur bei radiologisch nachgewiesener fortgeschrittener Gonarthrose (Kellgren-Lawrence-Grad 3 oder 4), nach vorangegangener konservativer Therapie über mindestens 3 Monate sowie bei hohem subjektivem Leidensdruck hinsichtlich der kniebezogenen Beschwerden und nach Ausschluss möglicher Kontraindikationen (Infektionen, Begleiterkrankungen, BMI ≥ 40 kg/m2) erfolgen. Modifizierbare Risikofaktoren (wie Rauchen, Diabetes mellitus, Anämie) sollen zuvor adressiert und ggf. optimiert werden. Die Ziele der Patient*innen sollen erfragt und deren Eintrittswahrscheinlichkeit gemeinsam besprochen werden. Schließlich ist die Entscheidung zur Knieendoprothese von Patient*in und Operateur*in gemeinsam zu treffen, wenn der zu erwartende Nutzen die möglichen Risiken überwiegt.Das Update der S2k-Leitlinie wurde um die unikondyläre Knieendoprothese erweitert, die präoperative Optimierung modifizierbarer Risikofaktoren ergänzt sowie Konkretisierungen der Hauptindikationskriterien vorgenommen. Y1 - 2024 U6 - https://doi.org/10.1055/a-2288-7254 SN - 1864-6697 PB - Georg Thieme Verlag KG ER - TY - GEN A1 - Froeschke, Samuel A1 - Bestha, Kranthi Kumar A1 - Fucke, Rico A1 - Schiemenz, Sandra A1 - Popov, Alexey A1 - Naumann, Marco A1 - Knupfer, Martin A1 - Giebeler, Lars A1 - Wolf, Daniel A1 - Kizhake Malayil, Ranjith Kumar A1 - Sivan, Saramgi Chencheriparambil A1 - Grafe, Hans-Joachim A1 - Gräßler, Nico A1 - Corredor, Laura T. A1 - Wolter, Anja U. B. A1 - Büchner, Bernd A1 - Schmidt, Peer A1 - Hampel, Silke T1 - Structural and Magnetic Transitions Caused by Dimer Formation in the CrCl3–MoCl3 Solid Solution T2 - Chemistry of Materials N2 - In this work, we apply the concept of solid solutions to the two 2D transition metal trihalides CrCl3 and MoCl3. While CrCl3 belongs to the magnetically active CrX3 family, the magnetism in MoCl3 is intrinsically suppressed by the formation of aligned Mo–Mo dimers, which also distort the regular honeycomb lattice that is typical for the 2D transition metal trihalides. We report suitable synthesis conditions for the gapless solid solution and crystal growth by chemical vapor transport. The CrCl3–MoCl3 solid solution was initially synthesized at 650 °C for 100 h under addition of MoCl5 as mineralizer, and bulk crystals were subsequently grown by vapor transport in a temperature gradient from 600 °C → 550 °C for 60 h. The obtained solid solution exhibits multiple composition-dependent phase transitions at room temperature, as confirmed by powder X-ray diffraction measurements. The possible presence of Mo–Mo dimers in the solid solution was further investigated by infrared, Raman, electron energy loss, and nuclear quadrupole resonance spectroscopies. The combined results indicate that the Mo–Mo dimers are present over a wide range of compositions. Their orientation changes from parallel alignment for compositions from 70% ≤ c(Mo3+) ≤ 100% to random orientation for samples with c(Mo3+) < 70% content, which significantly affects the course of lattice parameters. Finally, the magnetic properties of the powder samples show a correlation between the Mo3+ content and the transition temperature into the low-temperature phase. Y1 - 2024 U6 - https://doi.org/10.1021/acs.chemmater.3c03109 SN - 0897-4756 SN - 1520-5002 VL - 36 IS - 9 SP - 4240 EP - 4253 ER - TY - GEN A1 - Hansen, Felix A1 - Wels, Martin A1 - Froeschke, Samuel A1 - Popov, Alexey A1 - Wolf, Daniel A1 - Büchner, Bernd A1 - Schmidt, Peer A1 - Hampel, Silke T1 - Thermodynamic Evaluation and Chemical Vapor Transport of Few-Layer WTe2 T2 - Crystal Growth and Design N2 - Tungsten telluride WTe2 is the sole candidate of a group of two-dimensional layered transition metal dichalcogenides (TMDCs) MX2 with a thermodynamically stable 1T′-structure at room temperature. The binary system W/Te was audited with respect to a rational approach of planning and realization of a bottom-up synthesis of WTe2 nanostructures. Thus, the parameters of the synthesis via chemical vapor transports (CVT) were derived by thermodynamic simulations of the reaction pathway according to the Calphad method. Reflecting on the peritectic melting behavior at 1020 °C, the values of ΔfHm° (298 K) = −26.5 kJ·mol−1 and Sm° (298 K) = 132 J·mol−1 ·K−1 have been obtained. According to modeling, crystal growth by short time vapor transport is reasonable under the addition of bromine or TeBr4 in the temperature range between 650 and 750 °C. Experimental implementation of crystal growth of WTe2 nanosheets succeeded in a temperature gradient from 725 to 675 °C on yttria-stabilized zirconia (YSZ) (111) substrates, observing the deposition of single crystal sheets of high crystallinity with thicknesses of 15−20 nm (∼20−30 layers). The high crystallinity, pristine morphology, and overall quality of the deposited nanosheets is shown by means of atomic resolution transmission electron microscopy, selected area electron diffraction (SAED), and atomic force microscopy as well as profound double-polarized Raman spectroscopy. KW - Crystal growth KW - Chemical vapor transport KW - Thermodynamic modeling KW - 2D layered compounds KW - Chalcogenides KW - Phase diagram Y1 - 2020 UR - https://pubs.acs.org/doi/abs/10.1021/acs.cgd.0c01004 U6 - https://doi.org/10.1021/acs.cgd.0c01004 SN - 1528-7505 VL - 20 IS - 11 SP - 7341 EP - 7349 ER -