TY - RPRT A1 - Launert, Benjamin A1 - Pasternak, Hartmut A1 - Rhode, Michael A1 - Kromm, Arne A1 - Kannengießer, Thomas T1 - Erhöhung der Tragfähigkeit geschweißter I-Träger aus hochfestem Baustahl durch verbesserte Ansätze zur Berücksichtigung von Eigenspannungen Y1 - 2017 UR - https://www-docs.b-tu.de/fg-stahlbau/public/Fachgebiet_Stahlbau/AiF_TragEig/Kurvorstellung_P1035.pdf ER - TY - GEN A1 - Launert, Benjamin A1 - Pasternak, Hartmut T1 - Weld residual stresses effects in the design of welded plate girders: Simulation and Implementation T2 - Ce/papers N2 - Eurocode 3 offers different possibilities on a numerically-aided design of welded plate girders. In this, a geometrically and materially nonlinear analysis of the imperfect structure (GMNIA) provides the theoretically highest possible degree of realism. A correct implementation of “imperfections” is of critical importance in the practical application of this method. The current design rules are based on long term experience in terms of traditional (“old”) welding procedures and regular (“low strength”) steel grades. Thus, they provide very approximate (but safe) rules for these structures. With the introduction of modern shop welding operations and materials, many of these assumptions seem to be over-conservative. A revision of these rules is being processed in different national and international research projects. This particular study focusses on the weld residual stresses and their effects in conventional steel S355 and high strength steel S690. Metal active gas (MAG) welding under shop welding conditions was used. The measurement of weld residual stresses on component-like samples (carried out by the BAM Bundesanstalt für Materialforschung und -prüfung in Berlin) has been widely published. The hereupon based (simplified) welding simulation as part of a subsequent structural analysis is shown here. A novel numerical approach how to directly incorporate the results into large structural components models is presented. The capacity analysis is performed on a simple example for weak-axis buckling. The results indicate significant improvements in the utilization of load-bearing capacity and underline the superior buckling assignment for the S690 compared to conventional S355. The experimental validation of the findings is currently being prepared. KW - Stability KW - Welding imperfections KW - Residual stresses KW - Welding simulation KW - Nonlinear analysis Y1 - 2017 UR - http://onlinelibrary.wiley.com/doi/10.1002/cepa.144/abstract U6 - https://doi.org/10.1002/cepa.144 SN - 2509-7075 VL - 1 IS - 2-3 SP - 1039 EP - 1047 ER - TY - GEN A1 - Krausche, Thomas A1 - Launert, Benjamin A1 - Pasternak, Hartmut T1 - A study on the prediction of welding effects in steel box girders T2 - Ce/papers N2 - For standard sections including I-girders and rectangular box girders, several approaches on geometrical and structural imperfections are given in the literature, which can be implemented in a numerical analysis. For complex sections, as found in many of today's lightweight roof structures, these assumptions are conservative due to the sections typically unique shape, which leads to increased thicknesses or additional stiffening of the plates. This, on the other hand, can significantly affect fabrication costs. This paper aims to provide an overview on the possibilities in the numerical prediction of weld residual stresses and weld-induced deformations for these sections. The obtained values can be used in a subsequent numerical analysis to understand the structural behavior and optimize the design. A representative example on a section used in a steel compression ring is described and analyzed using the numerical welding simulation. A simplification of the originally transient weld procedure is used in order to reduce computation times to a practically reasonable level. In this context, the Abaqus Welding Interface (AWI) helps to automate working steps in conjunction with the definition of weld passes and their sequencing, which shall be shown in here. The applicability of this method is discussed showing also a need of further investigations in this field. This is especially with regard to result quality, which requires some experimental back-up. Nonetheless, this method could already help to show up tendencies or to identify potential critical spots in the design. KW - Innovative structures KW - Welding simulation KW - Abaqus Welding Interface Y1 - 2017 UR - http://onlinelibrary.wiley.com/doi/10.1002/cepa.500/abstract U6 - https://doi.org/10.1002/cepa.500 SN - 2509-7075 VL - 1 IS - 2-3 SP - 4410 EP - 4416 ER - TY - CHAP A1 - Krausche, Thomas A1 - Launert, Benjamin A1 - Pasternak, Hartmut T1 - Welding effects in unregularly steel box girders T2 - 6th Structural Engineers World Congress (SEWC 2017), Cancun/Mexico N2 - Several approaches on geometrical and structural imperfections are given in the literature for I sections and rectangular box girders. Those approximations of the residuals stress state can be implemented into the structural analysis using multi-purpose FEM program packages. The knowledge of the stress state of free forming cross sections has still to be determined. To fulfil a safe design, the assumptions mostly will be very conservative due to the lack of the assumed stress state. This will result directly to increased thicknesses or additional stiffening of the plates. Not only the material cost will rise, but also the fabrication costs like welding will be affected. This paper aims to provide an overview on the possibilities in the numerical prediction of weld residual stresses and weld induced deformations for cross sections with unique shapes. With the obtained values the tendencies of the residual stress state and deformations will be used to optimize the design. A representative example on a section used in a steel compression ring of a realized roof is described and analyzed using a simplification of a numerical welding simulation. The reduced simulation of the originally transient weld procedure was held to a practically reasonable level and can be reproduced for similar problems. The calculations used the Abaqus Welding Interface (AWI) to automate working steps in conjunction with the definition of weld passes and their sequencing. The field of the method that is discussed also a need of further investigations to prove its applicability. Some experimental back up is requires to verify the result quality. Nonetheless, this method could already help to show up tendencies or to identify potential critical spots in the design. Y1 - 2017 UR - http://sewc2017.org/ PB - Universidad Nacional Autónoma de México - UNAM ER - TY - CHAP A1 - Stapelfeld, Christoph A1 - Launert, Benjamin A1 - Pasternak, Hartmut A1 - Doynov, Nikolay A1 - Michailov, Vesselin T1 - Numerische Festigkeitsberechnung einer versteiften Struktur unter Berücksichtigung realitätsnaher geometrischer und struktureller Imperfektionen T2 - 110 Jahre DASt und 21. DASt-Forschungskolloquium an der Technischen Universität Kaiserslautern, 6./7. März 2018 N2 - Die Festigkeitsberechnung von Strukturen, zum Beispiel Platten oder Schalen, mittels der Finite-Elemente-Methode gehört schon seit längerem zum Stand der Technik. Berücksichtigt werden bei der Berechnung sowohl geometrische Nichtlinearitäten als auch das nichtlineare Verhalten des Werkstoffs. Die geometrischen und strukturellen Imperfektionen werden bei der Ermittlung der Festigkeit zumeist in ausschließlich geometrischen Imperfektionen, wie bspw. Kombinationen aus Fertigungstoleranzen und den Ergebnissen von Beulanalysen zusammengefasst. Zur Rechtfertigung dieser Vorgehensweise werden die geometrischen Imperfektionen gemäß DIN EN 1993-1-5 erhöht. In einem Kommentar zur selben Norm findet sich ebenfalls eine Empfehlung zur Berücksichtigung von Schweißimperfektionen in Form von vereinfachten Längseigenspannungsverläufen. Diese werden in Abhängigkeit der Fließgrenzspannung des Werkstoffs bei Raumtemperatur und der Dicken der Fügepartner angenommen. Sowohl die Annahme rein geometrischer Imperfektionen als auch die Berücksichtigung vereinfachter Eigenspannungszustände, sind mit Sicherheitszuschlägen behaftet. Durch eine realitätsnähere Berücksichtigung von strukturellen und geometrischen Imperfektionen, hervorgerufen durch Schweißprozesse, kann die tatsächliche Tragfähigkeit einer Struktur wesentlich exakter bestimmt werden. Inhalt dieses Artikels ist die Anwendung eines analytisch-numerischen Hybridmodells zur Schweißimperfektionsberechnung an einer doppelt versteiften Platte und einer anschließenden Festigkeitsanalyse. Eingangs wird das analytische Modell vorgestellt und auf die grundlegenden physikalischen Zusammenhänge eingegangen. Es folgt die Erläuterung des Kopplungsalgorithmus zwischen analytischem Modell und der numerischen Berechnung. Angewendet an der doppelt versteiften Platte, wird ein realitätsnaher geometrischer und struktureller Imperfektionszustand berechnet. Eine anschließende Traglastanalyse gibt Aufschluss über das Verformungsverhalten unter achsialer Krafteinwirkung. Zur Bewertung der Ergebnisse wird ein Modell gleicher geometrischer Abmessungen und Werkstoffkennwerte aus der Literatur herangezogen. Berechnet wurden die ersten 6 Eigenformen mittels analytischer und numerischer Modelle sowie die Last-Verformungskurven unter der Annahme unterschiedlicher geometrischer Imperfektionen. Um die Vergleichbarkeit der Ergebnisse zu sichern, wird eingangs die Lagerung des Modells sowie der Kraftangriffspunkt in Längsrichtung invers, durch den Vergleich der ersten 6 Beulformen sowie der Last-Verformungskurven dreier Imperfektionen, bestimmt. Darauf aufbauen wird die Last-Verformungskurve für einen überlagerten Imperfektionszustand berechnet, wobei die geometrischen Imperfektionen aus den Fertigungstoleranzen abgeleitet und die strukturellen idealisiert, gemäß DIN EN 1993-1-5, gewählt werden. Abschließend werden alle Last-Verformungskurven einander gegenübergestellt. Anhand des Vergleichs kann quantifiziert werden, wie konservativ die einzelnen angenommenen Imperfektionen sind und wie sich der Verformungsverlauf darstellt, berechnet man diesen unter Verwendung realitätsnaher geometrischer und struktureller Imperfektionen. Y1 - 2018 SN - 978-3-941687-27-1 SP - 245 EP - 249 PB - Deutscher Ausschuß für Stahlbau DASt CY - Düsseldorf ER - TY - CHAP A1 - Ragotzky, Birgit A1 - Launert, Benjamin A1 - Krausche, Thomas ED - Virdi, Kuldeep ED - Tenhunen, Lauri T1 - Welding simulation for the calculation of the welding residual stresses in welded I-girders T2 - Proceedings of the METNET Seminar 2017 in Cottbus Y1 - 2018 UR - https://issuu.com/hamkuas/docs/hamk_metnet_cottbus_2017 SN - 978-951-784-794-0 SP - 56 EP - 68 PB - Häme University of Applied Sciences (HAMK) CY - Hämeenlinna, Finland ER - TY - GEN A1 - Garifullin, Marsel A1 - Launert, Benjamin A1 - Heinisuo, Markku A1 - Pasternak, Hartmut A1 - Mela, Kristo A1 - Pajunen, Sami T1 - Effect of welding residual stresses on local behavior of rectangular hollow section joints. Part 1 - Development of numerical model T1 - Einfluss der Schweißeigenspannungen auf die Tragfähigkeit von Rechteck-Hohlprofil-Knoten. Teil 1: Entwicklung eines numerischen Modells) T2 - Bauingenieur N2 - Welded tubular joints are widely used in structural engineering due to their excellent resistance and stiffness in contrast to open sections, as well as simpler end preparation. Welding residual stresses that occur in these joints after the welding process can affect their structural behavior. Some recent experimental studies have shown that this effect can be considerable. This study numerically evaluates the influence of welding residual stresses on the behavior of rectangular hollow section T joints. The paper consists of two parts. Part I develops and validates a finite element model for the joints directly taking into account welding residual stresses by means of an upstream thermomechanical simulation of the welding process. It is proven that particular attention needs to be paid to the discretization of the model, the material properties and the adequate description of the weld heat input. The validation with experimental results shows that the developed numerical model properly captures the local structural behavior of tubular joints and can be efficiently used for further investigations. Part II employs the constructed model to investigate the effect of welding residual stresses on the resistance and initial stiffness of the considered joints. N2 - Geschweißte Hohlprofilknoten sind aufgrund besserer Festigkeits – und Steifigkeitseigenschaften im Vergleich zu offenen Profilen sowie ihrer einfacheren Fertigung weit verbreitet. Schweißeigenspannungen, die infolge des Fügens der Einzelkomponenten mittels Schweißen entstehen, können deren Tragverhalten zum Teil stark beeinflussen, was auch durch einige neuere Untersuchungen belegt wird. Dieser Beitrag beschreibt eine erweiterte Vorgehensweise für die Finite-Elemente-Modellierung am Beispiel eines T-Knotens aus Rechteckhohlprofilen. Der Beitrag gliedert sich in zwei Teile. Teil 1 beinhaltet die Entwicklung und Validierung eines numerischen Modells, welches Schweißeinflüsse durch eine vorangehende thermomechanische Simulation explizit modelliert und diese in nachfolgende Berechnungsschritte einbezieht. Dabei werden die Bedeutung einer geeigneten Vernetzung des Modells, der Materialeigenschaften und eines zutreffenden Schweißwärmeeintrags diskutiert. Die Validierung mit experimentellen Ergebnissen zeigt die Eignung des entwickelten numerischen Modells und dass dieses das lokale Tragverhalten entsprechender Knotenverbindungen korrekt erfasst. Es kann daher für nachfolgende Untersuchungen weiterverwendet werden. Teil 2 zeigt die diesbezüglich durchgeführten Parameterstudien, um die Auswirkungen der Schweißeigenspannungen auf die Tragfähigkeit und die Anfangssteifigkeit der untersuchten Knotenverbindung darzustellen. KW - Einfluss der Eigenspannungen auf Verbindungen Y1 - 2018 UR - https://www.bauingenieur.de/bauing/article.php?data[article_id]=89266 SN - 1436-4867 SN - 0005-6650 VL - 93 IS - 4 SP - 152 EP - 159 ER - TY - GEN A1 - Garifullin, Marsel A1 - Launert, Benjamin A1 - Heinisuo, Markku A1 - Pasternak, Hartmut A1 - Mela, Kristo A1 - Pajunen, Sami T1 - Effect of welding residual stresses on local behavior of rectangular hollow section joints. Part 2 – Parametric studies T1 - Einfluss der Schweißeigenspannungen auf die Tragfähigkeit von Rechteck-Hohlprofil-Knoten. Teil 2 – Parameterstudien T2 - Bauingenieur N2 - Welding residual stresses that occur in tubular joints after the welding process affect their structural behavior. To ensure that these stresses do not negatively act on the load-bearing capacity of joints, their influence should be carefully investigated. This paper represents the second part of a study that numerically evaluates the structural behavior of rectangular hollow section T joints taking into account welding residual stresses. The finite element model developed in Part 1 is now used to evaluate their effect on the resistance and initial stiffness of tubular joints. The conducted parametric analyses show that welding residual stresses have a positive influence of 1–19 % on the plastic resistance of tubular joints and insignificantly reduce their initial stiffness. At the same time, the behavior of the considered joints is found not to depend on the welding sequence. N2 - Schweißeigenspannungen können das Tragverhalten geschweißter Hohlprofilknoten zum Teil stark beeinflussen. Um mögliche negative Einflüsse auf die Tragfähigkeit auszuschließen, sollte der Eigenspannungseinfluss mitberücksichtigt werden. Dieser Beitrag bildet den zweiten Teil einer numerischen Untersuchung an geschweißten Rechteck-Hohlprofil-Knoten unter Berücksichtigung der vorgenannten Spannungen. Darin werden in Teil 1 entwickelten Modelle dazu verwendet, deren Auswirkungen auf die Tragfähigkeit und die Anfangssteifigkeit der Knotenverbindung darzustellen. Die Ergebnisse zeigen im untersuchten Parameterfeld eine Traglaststeigerung zwischen 1 % und 19 %. Die Anfangssteifigkeit wird generell nur geringfügig reduziert. Gleichzeitig wird gezeigt, dass die Schweißreihenfolge in den untersuchten Fällen keinen nennenswerten Einfluss auf die Tragfähigkeit ausübt. Y1 - 2018 UR - https://www.bauingenieur.de/bauing/article.php?data[article_id]=89481 SN - 1436-4867 SN - 0005-6650 VL - 93 IS - 5 SP - 207 EP - 213 ER - TY - GEN A1 - Li, Zheng A1 - Launert, Benjamin A1 - Pasternak, Hartmut T1 - Application of the stochastic finite element method in welding simulation T2 - Welding in the World N2 - Due to the uncertain microscopic structure of the material, the strength of the material exhibits strong randomness. This randomness results in uncertain response of the structure in the sequentially coupled thermal-mechanical analysis by welding simulation. Because of the limitations of deterministic welding simulation, the stochastic finite element method with random field will be introduced into the welding simulation, so that the welded structure can be more accurately calculated in the stability and reliability structural analysis. Particularly, it is necessary to propose reasonable distributions of residual stress from welding simulations based on statistical and reliability theories. This paper is intended to implement the stochastic finite element method in the welding simulation using a general-purpose simulation program and to demonstrate the potential of the proposed approach. Furthermore, the statistical distribution function of the welding simulation response is obtained by maximum entropy fitting method. Then, a numerical example is presented by the proposed method. Y1 - 2018 UR - https://rdcu.be/NT9F U6 - https://doi.org/10.1007/s40194-018-0596-4 SN - 0043-2288 SN - 1878-6669 VL - 62 IS - 5 SP - 905 EP - 912 ER - TY - CHAP A1 - Garifullin, Marsel A1 - Launert, Benjamin A1 - Heinisuo, Markku A1 - Pasternak, Hartmut A1 - Mela, Kristo A1 - Pajunen, Sami T1 - Effect of Welding Residual Stresses on Behavior of Tubular T Joints T2 - 17th International Conference on Computing in Civil and Building Engineering N2 - Welded tubular joints are widely used in structural engineering due to their excellent resistance and stiffness, as well as simple connection. However, the welding process induces residual stresses in the welding area that can affect the structural behavior of joints. Currently very few papers investigate welding residual stresses in relation to tubular joints. This paper develops a finite element model of rectangular hollow section T joints considering welding residual stresses. Attention is paid particularly to welding sequences. The developed model is used to evaluate the effect of welding residual stresses on the resistance and initial stiffness of tubular joints. The results show that welding residual stresses increase the plastic resistance of rectangular hollow section joints under in-plane bending and axial brace loading. Y1 - 2018 UR - http://programme.exordo.com/icccbe2018/delegates/presentation/267/ UR - https://icccbe2018.exordo.com/files/papers/104/final_draft/Effect_of_Welding_Residual_Stresses_on_Behavior_of_Tubular_T_Joints.pdf ER - TY - CHAP A1 - Stapelfeld, Christoph A1 - Launert, Benjamin A1 - Pasternak, Hartmut A1 - Doynov, Nikolay A1 - Michailov, Vesselin ED - Seefeldt, Marc T1 - Strength Calculation of Stiffened Structures Taking Into Consideration Realistic Weld Imperfections T2 - European Conference on Residual Stresses 2018, ECRS-10, Leuven, Belgium, 11-14th September, 2018 N2 - The topic of this article is the application of an analytical numerical hybrid model for a realistic prediction of imperfections induced by welds. At the beginning, the analytical model, its physical basis as well as the physical interrelationships are explained. This is followed by the explanation of the coupling procedure between the analytical model and the numerical calculation. Afterwards, the coupled hybrid model is applied on the investigated stiffened curved structure for the determination of the weld imperfections. An ultimate load analysis gives information about the load carrying behavior under axial loading. The results are compared against the traditional approach using eigenmode-based imperfections. The comparison underlines the potential additional utilization of load bearing capacity by this new approach. Y1 - 2018 SN - 978-1-945291-88-3 SN - 978-1-945291-89-0 U6 - https://doi.org/10.21741/9781945291890-39 SP - 245 EP - 250 PB - Materials Research Forum LLC CY - Millersville, PA ER - TY - GEN A1 - Stapelfeld, Christoph A1 - Launert, Benjamin A1 - Pasternak, Hartmut A1 - Doynov, Nikolay A1 - Michailov, Vesselin T1 - Traglastberechnung versteifter Platten und Schalen unter Berücksichtigung realer Schweißimperfektionen T2 - Bauingenieur N2 - Imperfektionen, die bei Traglastberechnungen Berücksichtigung finden müssen, haben ihre Ursachen in Herstellungs- und Fertigungstoleranzen oder werden durch das Schweißen und den damit zumeist einhergehenden Nachbehandlungen in den Bauteilen hervorgerufen. Durch die Wärmewirkung des Schweißens entstehen sowohl sehr große Verformungen als auch signifikante Zug und Druckspannungen. Der strukturelle und geometrische Imperfektionsgrad wird somit maßgeblich von der Anzahl und der Lage der Schweißnähte sowie den Schweißparametern bestimmt. Für die Berücksichtigung in Traglastberechnungen ist ein physikalisch fundiertes Modell erforderlich, welches die Schweißimperfektionen schnell und präzise berechnet. Das gekoppelte analytisch numerische Hybridmodell erfüllt diese Kriterien. Die mathematischen Grundlagen des analytischen Modells sowie die Kopplung mit der numerischen Finite-Elemente-Berechnung werden eingangs vorgestellt und die Anwendung zur Berechnung von Verzügen an einer Schiffsektion demonstriert. Darauffolgend wird das Hybridmodell an einer eben und einer gekrümmten versteiften Platte zur Berechnung der Schweißimperfektionen angewendet. Anschließende Traglastberechnungen sowie der Vergleich mit den Ergebnissen unter der Annahme einer geometrischen Ersatzimperfektion in Form des kritischsten Eigenwerts gibt Auskunft darüber, welches Potenzial die realitätsnahe direkte Berücksichtigung von Schweißimperfektionen birgt. Y1 - 2018 SN - 0005-6650 VL - 93 IS - 10 SP - 403 EP - 411 ER - TY - CHAP A1 - Stapelfeld, Christoph A1 - Launert, Benjamin A1 - Pasternak, Hartmut A1 - Doynov, Nikolay A1 - Michailov, Vesselin T1 - The Influence of Geometrical and Welding Imperfections on the Strength of Stiffened Structures T2 - High Performance Steel Structures Research Council (HPSSRC), Delft, Netherlands, 2018 N2 - The strength calculation of stiffened plates and shells via finite element simulation has been part of the state of the art for a long time. Geometrical nonlinearities as well as the nonlinear material behavior are considered within the calculation. To simplify, both types of imperfections, geometrical and structural ones, are mostly combined in these strength calculations being considered as equivalent geometrical imperfections. Values for standard cases are included in EN 1993-1-5 in case of plated structures or 1-6 in case of shells. A second possibility is the separate definition of fabrication tolerances and residual stresses, as far as they are known. With increasing complexity of the structure, less information are however available on geometrical and particularly structural imperfections. Nevertheless, by means of a more realistic consideration of these values, the actual ultimate load can be determined significantly more exactly and the performance of high performance steel structures is increased. In the investigated cases, deformations and stresses arise mainly due to welding. Therefore, the topic of this article is the application of an analytical numerical hybrid model for predicting imperfections induced by welds. This is presented on an example of a stiffened steel structure and a subsequent ultimate load calculation. At the beginning the analytical model, its physical basis as well as the physical interrelationships are introduced and explained. This is followed by the explanation of the coupling procedure between the analytical model and the numerical calculation for the calculation of weld-induced deformations and residual stresses. The significance of the hybrid model is proven by means of a few sample applications. For a realistic determination of the weld imperfections in the investigated stiffened structure, the coupled hybrid model is used afterwards. An ultimate load analysis gives information about the load carrying behavior under axial loading. The results are compared with the results of an ultimate load analysis from a literature example assuming different eigenvalues with different scaling. The results underline the potential additional utilization of load bearing capacity by this new approach. KW - Welding KW - Stresses KW - Strains KW - Imperfections KW - Stiffened Structures KW - Distortions Y1 - 2018 UR - https://www-docs.b-tu.de/fg-stahlbau/public/Fachgebiet_Stahlbau/publikationen/Workshop_Proceedings_of_HPSSRC-updated_cs.pdf SP - 191 EP - 201 ER - TY - GEN A1 - Tankova, Trayana A1 - Silva, Luís Simões da A1 - Balakrishnam, Marimuthu A1 - Rodrigues, Dulce A1 - Launert, Benjamin A1 - Pasternak, Hartmut A1 - Tun, Tin Yadanar T1 - Residual stresses in welded I section steel members T2 - Engineering Structures N2 - Residual stresses have major influence on the stability of steel members. It is well-known that, due to the differences in manufacturing procedures, the residual stresses for welded and hot – rolled members are rather different. In the same way, despite several studies on residual stresses distribution and magnitude for hot-rolled members were already done, for prismatic and tapered welded I section steel members the investigation is still very scarce. In the current work, an experimental programme on the buckling resistance of tapered members, with different tapering ratios and section heights, was conducted and residual stress measurements were carried out using the sectioning method. Numerical simulations of the heat input during welding were also performed in order to predict the residual stress fields. A statistical analysis of the residual stresses distribution for welded I section members was performed, using the experimental and numerical results, as well as literature data. Systematized information on residual stresses distribution and magnitude was generated and some guidelines for the statistical characterization of residual stresses in welded members were proposed. KW - Residual stresses KW - Welded sections KW - Steel KW - Eurocode 3 KW - Stability KW - Welding simulation KW - I section KW - Experimental tests Y1 - 2019 U6 - https://doi.org/10.1016/j.engstruct.2019.109398 SN - 0141-0296 VL - 197 ER - TY - GEN A1 - Doynov, Nikolay A1 - Stapelfeld, Christoph A1 - Michailov, Vesselin A1 - Pasternak, Hartmut A1 - Launert, Benjamin ED - Sommitsch, Christof ED - Enzinger, Norbert ED - Mayr, Peter T1 - Distortion analysis of large scaled welded structures T2 - Mathematical Modelling of Weld Phenomena 12 : selected peer reviewed papers from the 12th International Seminar Numerical Analysis of Weldability : September 23-26, 2018, Graz, Schloss Seggau - Austria N2 - The work presents an innovative approach for simulation of welding induced distortions, which allows taking into consideration the local effects of the welding process as well as the global interactions in the structure. The approach bases on an integration of analytical and numerical calculation’s procedures in a hybrid model, realized with the aid of the inherent strain concept. The analytical procedure calculates the shrinkage strain components and area of the plastic deformed zone, caused by welding. The calculated strains are then transferred to the global finite element model in order to predict the distortions and stresses in the structure after every welding stage, as well as their final state. The consideration of welding scenarios, weld sequence, clamping conditions and the assembling stages is done by taking into account the intermediate variation of the strain state during the manufacturing steps. The article gives the theoretical basis of the analytical model. The consideration of the essential physical relations is put into discussion. The application of the model is illustrated on complex structures. Its reliability and practicability are demonstrated by means of a validation study. Y1 - 2019 SN - 978-3-85125-615-4 U6 - https://doi.org/10.3217/978-3-85125-615-4 SP - 254 EP - 280 PB - Verlag der Technischen Universität Graz CY - Graz ER - TY - GEN A1 - Launert, Benjamin A1 - Li, Zheng A1 - Pasternak, Hartmut ED - Zingoni, Alphose T1 - Development of a new method for the direct numerical consideration of welding effects in the component design of welded plate girders T2 - Advances in engineering materials, structures and systems : innovations, mechanics and applications : proceedings of the 7th International Conference on Structural Engineering, Mechanics, and Computation (SEMC 2019), September 2-4, 2019, Cape Town, South Africa Y1 - 2019 SN - 978-1-138-38696-9 SP - 1143 EP - 1147 PB - Taylor & Francis Group CY - London ER - TY - GEN A1 - Stapelfeld, Christoph A1 - Launert, Benjamin A1 - Pasternak, Hartmut A1 - Doynov, Nikolay A1 - Michailov, Vesselin T1 - Improve load capacity calculations by considering realistic imperfections induced by welding for plates and shells T2 - Stability and ductility of steel structures 2019 : proceedings of the International Colloquia on Stability and Ductility of Steel Structures (SDSS 2019), September 11-13, 2019, Prague, Czech Republic Y1 - 2019 UR - https://www.b-tu.de/fg-stahlbau/publikationen/veroeffentlichungen SN - 978-0-367-33503-8 SP - 1059 EP - 1067 PB - CRC Press CY - Boca Raton ER - TY - GEN A1 - Pasternak, Hartmut A1 - Li, Zheng A1 - Stapelfeld, Christoph A1 - Jäger-Cañás, Andreas A1 - Launert, Benjamin T1 - Considering realistic weld imperfections in load bearing capacity calculations of ring-stiffened shells using the analytical numerical hybrid model T2 - Stability and Ductility of Steel Structures 2019 : Proceedings of the International Colloquia on Stability and Ductility of Steel Structures (SDSS 2019), September 11-13, 2019, Prague, Czech Republic Y1 - 2019 SN - 978-0-429-32024-8 SN - 978-0-367-33503-8 U6 - https://doi.org/10.1201/9780429320248 SP - 882 EP - 889 PB - CRC Press CY - London ET - 1st Edition ER - TY - BOOK A1 - Pasternak, Hartmut A1 - Stapelfeld, Christoph A1 - Launert, Benjamin A1 - Michailov, Vesselin A1 - Doynov, Nikolay T1 - Ermittlung der Tragfähigkeit neuartiger stählerner Schalenbauwerke unter realitätsnaher Berücksichtigung des Schweißverzugs Y1 - 2020 SN - 978-3-946885-89-4 PB - Forschungsvereinigung Stahlanwendung e. V. CY - Düsseldorf ER - TY - GEN A1 - Wang, Jian A1 - Euler, Mathias A1 - Pasternak, Hartmut A1 - Li, Zheng A1 - Krausche, Thomas A1 - Launert, Benjamin T1 - Bending capacity of single and double-sided welded I-section girders: Part 1: Experimental investigations T2 - Current Perspectives and New Directions in Mechanics, Modelling and Design of Structural Systems : Proceedings of The Eighth International Conference on Structural Engineering, Mechanics and Computation, 5-7 September 2022, Cape Town, South Africa N2 - The lateral-torsional buckling resistance of welded steel girders is affected by their residual stresses and geo-metric imperfections. Generally, both influences are mainly controlled by the manufacturing process, in partic-ular the welding of the girder. This paper presents experimental investigations on four laterally unbraced welded steel girders with thin-walled I-sections, whose flange-to-web junctions are welded from one or two sides to evaluate the fabrication influence. The investigations include lateral-torsional buckling tests under combined bending and torsion loading caused by three-point bending due to an eccentric vertical single force. The geometric imperfections of the welded test girders are determined by 3D laser scanning. The test results show that the influence of the geometric imperfections and the residual stresses on the lateral-torsional buck-ling resistance is limited for the tested girders. KW - Experimental investigations KW - single and double-sided welds KW - imperfections KW - lateral-torsional buckling KW - 3D laser scanning Y1 - 2022 SN - 978-1-00-334845-0 U6 - https://doi.org/10.1201/9781003348443-159 SP - 975 EP - 980 PB - CRC Press CY - Boca Raton ER -