TY - CHAP A1 - Launert, Benjamin A1 - Rhode, Michael A1 - Pasternak, Hartmut A1 - Kannengießer, Thomas ED - Dubina, Dan ED - Ungureanu, Viorel T1 - Welding residual stresses in high-strength steel. Experimental results T2 - The International Colloquium on Stability and Ductility of Steel Structures N2 - This article presents the latest results of an ongoing national research project on improved models for the prediction of welding residual stresses of thick-plated welded I-girders. The experimental program is presented and the importance of different influencing factors on the residual stresses is discussed in detail. All results are compared for mild (S355J2+N) and high strength (S690QL) steel. Finally, conclusions for further works are drawn. KW - Residual stresses, High-strength steel, Welded sections, Measurement Y1 - 2016 SN - 978-92-9147-133-1 SP - 517 EP - 524 PB - Ernst & Sohn ET - 2016 edition ER - TY - CHAP A1 - Pasternak, Hartmut A1 - Launert, Benjamin A1 - Kannengießer, Thomas A1 - Rhode, Michael ED - Zingoni, Alphose T1 - Residual stresses and imperfections in welded high-strength I-shape members T2 - Insights and Innovations in Structural Engineering, Mechanics and Computation, Proceedings of the Sixth International Conference on Structural Engineering, Mechanics and Computation, Cape Town, South Africa, 5-7 September 2016 N2 - This article addresses the imperfections caused by the weld assembly in I-shape sections made of two structural steel grades. Load influencing imperfections are assumed as deviations from the ideal shape (e.g. bending distortion) and longitudinal residual stresses. The quality of a numerically aided design of components exposed to either compression and/or bending is significantly affected, depending on these parameters [1]. The Eurocode provides robust simplified models. As a result, the Ultimate Limit State (ULS) is approached on a conservative basis. The following investigations are aimed at providing further guidance on these values in component-like specimens. The long term goal is an improved understanding of the load-bearing capacity of such sections. As a first step in this process, the experimental and corresponding numerical studies are presented. Y1 - 2016 UR - https://www.crcpress.com/Insights-and-Innovations-in-Structural-Engineering-Mechanics-and-Computation/Zingoni/p/book/9781138029279 SN - 978-1-138-02927-9 SP - 403 EP - 404 PB - Taylor & Francis CY - London ER - TY - CHAP A1 - Launert, Benjamin A1 - Rhode, Michael A1 - Kromm, Arne A1 - Pasternak, Hartmut A1 - Kannengießer, Thomas ED - Holden, Thomas M. ED - Muránsky, Ondrej ED - Edwards, Lyndon T1 - Residual Stress Influence on the Flexural Buckling of Welded I-Girders T2 - Residual Stresses 2016 – ICRS-10 N2 - The nonlinear analysis became a common tool to precisely assess the load-bearing behavior of steel beam and column members. The failure level is significantly influenced by different types of imperfections, among geometric also structural imperfections (residual stresses). Here are still gaps in the knowledge. Nowadays, 3-D welding simulation developed to a level where it could provide reliable estimation of weld-induced distortion and residual stresses. Nevertheless, modelling and computational effort are still in a less practicable range. In this study a simplified procedure to implement residual welding stresses in continuous large scale members is proposed and the influence on the ultimate limit state of slender members in compression is evaluated for two common structural steel grades. The results showed significant improvements in the utilization of load bearing capacity compared with simplified design methods. The comparatively general approach in this study offers potential for future optimization. KW - Stability Design KW - Finite Element Method KW - 2-D Welding Simulation KW - Inherent Strain KW - PDA Y1 - 2016 UR - http://www.mrforum.com/product/9781945291166/ SN - 978-1-94529116-6 U6 - https://doi.org/10.21741/9781945291173-19 SP - 109 EP - 114 PB - Materials Research Forum LLC CY - Millersville, PA ER - TY - CHAP A1 - Kromm, Arne A1 - Rhode, Michael A1 - Launert, Benjamin A1 - Dixneit, Jonny A1 - Kannengießer, Thomas A1 - Pasternak, Hartmut ED - Holden, Thomas M. ED - Muránsky, Ondrej ED - Edwards, Lyndon T1 - Combining Sectioning Method and X-Ray Diffraction for Evaluation of Residual Stresses in Welded High Strength Steel Components T2 - Residual Stresses 2016 - ICRS-10 N2 - Residual stresses and distortions in welded I-girders for steel construction are relevant when evaluating the stability of steel beams and column members. The application of high strength steels allows smaller wall thicknesses compared to conventional steels. Therefore, the risk of buckling has to be considered carefully. Due to the lack of knowledge concerning the residual stresses present after welding in high strength steel components conservative assumptions of their level and distribution is typically applied. In this study I-girders made of steels showing strengths of 355 MPa and 690 MPa were welded with varying heat input. Due to the dimension of the I-girders and the complex geometry the accessibility for residual stress measurement using X-ray diffraction was limited. Therefore, saw cutting accompanied by strain gauge measurement has been used to produce smaller sections appropriate to apply X-ray diffraction. The stress relaxation measured by strain gauges has been added to residual stresses determined by X-ray diffraction to obtain the original stress level and distribution before sectioning. The combination of both techniques can produce robust residual stress values. From practical point of view afford for strain gauge application can be limited to a number of measuring positions solely to record the global amount of stress relaxation. X-ray diffraction can be applied after sectioning to determine the residual stresses with sufficient spatial resolution. KW - Weld Residual Stress KW - Sectioning Method KW - X-Ray Diffraction Y1 - 2016 UR - http://www.mrforum.com/product/9781945291166/ SN - 978-1-94529116-6 U6 - https://doi.org/10.21741/9781945291173-28 SP - 163 EP - 168 PB - Materials Research Forum LLC CY - Millersville, PA ER - TY - GEN A1 - Launert, Benjamin A1 - Rhode, Michael A1 - Kromm, Arne A1 - Pasternak, Hartmut A1 - Kannengießer, Thomas T1 - Measurement and numerical modeling of residual stresses in welded HSLA component-like I-girders T2 - Welding in the World N2 - The present contribution shows the residual stress results obtained from experiments with the sectioning method in comparison to global (structural) welding simulation models on component-like (i.e., large scale) I-girders made of structural steel grades S355 and S690QL. Plates were welded by conventional gas metal arc welding using two different heat inputs. In addition, the base material was assumed to be approximately stress-free. Based on these results, conclusions and recommendations for the design of welded I-girders are drawn. KW - Residual Stresses KW - Microalloyed steels KW - Girders KW - MAG welding KW - Simulating Y1 - 2016 UR - http://rdcu.be/n6mU U6 - https://doi.org/10.1007/s40194-016-0413-x SN - 0043-2288 SN - 1878-6669 VL - 61 IS - 2 SP - 223 EP - 229 ER - TY - GEN A1 - Pasternak, Hartmut A1 - Launert, Benjamin A1 - Kannengießer, Thomas A1 - Rhode, Michael T1 - Advanced Residual Stress Assessment of Plate Girders Through Welding Simulation T2 - Procedia Engineering N2 - This article provides an impression on potentials in applying nowadays welding simulation tools in construction design. This is carried out exemplary on plate girders from two structural steel grades. The calculated residual stresses are compared with measurements by sectioning method. It has been repeatedly stated that present Eurocode models fail to approximate the residual stresses. Especially for high strength steel (HSS) only limited information is available on realistic occurring residual stresses in typical I-girders. The investigations are aimed to give further guidance on these values. A few proposals on advanced models are discussed. KW - Residual stresses KW - Plate girders KW - I-shape sections KW - High-strength steel KW - Welding simulation KW - Advanced models Y1 - 2017 U6 - https://doi.org/10.1016/j.proeng.2017.02.013 SN - 1877-7058 VL - 172 SP - 23 EP - 30 ER - TY - RPRT A1 - Launert, Benjamin A1 - Pasternak, Hartmut A1 - Rhode, Michael A1 - Kromm, Arne A1 - Kannengießer, Thomas T1 - Erhöhung der Tragfähigkeit geschweißter I-Träger aus hochfestem Baustahl durch verbesserte Ansätze zur Berücksichtigung von Eigenspannungen Y1 - 2017 UR - https://www-docs.b-tu.de/fg-stahlbau/public/Fachgebiet_Stahlbau/AiF_TragEig/Kurvorstellung_P1035.pdf ER - TY - GEN A1 - Scharf-Wildenhain, Ronny A1 - Hälsig, André A1 - Härtel, Sebastian A1 - Wandtke, Karsten A1 - Schröpfer, Dirk A1 - Kromm, Arne A1 - Kannengießer, Thomas T1 - Einfluss der Wärmeführung auf die Eigenschaften und fertigungsbedingten Beanspruchungen additiv geschweißter hochfester Feinkornbaustähle T2 - 42. Assistentenseminar Fügetechnik KW - Additive Fertigung; Eigenspannungen; Hochfester Stahl; Kaltrisssicherheit; MAG-Schweißen Y1 - 2022 SN - 978-3-96144-210-2 SP - 94 EP - 101 PB - DVS Media GmbH CY - Düsseldorf ER -