TY - GEN A1 - Franken, Tim A1 - Duggan, Alexander A1 - Tao, Feng A1 - Matrisciano, Andrea A1 - Lehtiniemi, Harry A1 - Borg, Anders A1 - Mauß, Fabian T1 - Multi-Objective Optimization of Fuel Consumption and NOx Emissions of a heavy-duty Diesel engine using a Stochastic Reactor Model T2 - SAE technical paper N2 - Highly fuel-efficient Diesel engines, combined with effective exhaust aftertreatment systems, enable an economic and low-emission operation of heavy-duty vehicles. The challenge of its development arises from the present engine complexity, which is expected to increase even more in the future. The approved method of test bench measurements is stretched to its limits, because of the high demand for large parameter variations. The introduction of a physics-based quasi-dimensional stochastic reactor model combined with tabulated chemistry enables the simulation-supported development of these Diesel engines. The stochastic reactor model mimics mixture and temperature inhomogeneities induced by turbulence, direct injection and heat transfer. Thus, it is possible to improve the prediction of NOx emissions compared to common mean-value models. To reduce the number of designs to be evaluated during … KW - Highly fuel-efficient Diesel engines Y1 - 2019 SN - 0096-5170 SN - 0148-7191 IS - 2019-01-1173 ER - TY - GEN A1 - Malliotakis, Zisis A1 - Banyon, Colin A1 - Zhang, Kuiwen A1 - Wagnon, Scott W. A1 - Rodriguez Henriquez, Jose Juan A1 - Vourliotakis, George A1 - Keramiotis, Christos A1 - Founti, Maria A1 - Mauß, Fabian A1 - Pitz, William J. A1 - Curran, Henry J. T1 - Testing the validity of a mechanism describing the oxidation of binary n-heptane/toluene mixtures at engine operating conditions T2 - Combustion and Flame N2 - The aim of this work is to evaluate the influence of the n-heptane/toluene ratio on the reactivity of binary toluene reference fuels (TRFs), through a combined experimental and numerical work. Novel experimental ignition delay time (IDT) data of three binary TRFs of varying n-heptane/toluene ratios have been obtained in a high-pressure shock tube and in a rapid compression machine at conditions relevant to novel engine operation. Measurements have been performed at two pressures (10 and 30 bar), and at three fuel/air equivalence ratios (0.5, 1.0 and 2.0) for TRF mixtures of 50%, 75% and 90% by volume toluene concentration, over the temperature range of 650–1450 K. It was found that, increasing the n-heptane content, led to an increase in reactivity and shorter measured IDTs. Reduced sensitivity to the equivalence ratio was observed at high temperatures, especially for high toluene content mixtures. A … KW - The aim of this work is to evaluate the influence of the n-heptane/toluene Y1 - 2019 U6 - https://doi.org/10.1016/j.combustflame.2018.10.024 SN - 0010-2180 VL - 199 SP - 241 EP - 248 ER - TY - GEN A1 - Franken, Tim A1 - Klauer, Christian A1 - Kienberg, Martin A1 - Matrisciano, Andrea A1 - Mauß, Fabian T1 - Prediction of thermal stratification in an engine-like geometry using a zero-dimensional stochastic reactor model T2 - International Journal of Engine Research KW - Prediction of thermal stratification Y1 - 2019 UR - https://journals.sagepub.com/eprint/5AKgEhAVA8RDS2tQWdGK/full SN - 2041-3149 U6 - https://doi.org/10.1177/1468087418824217 SN - 1468-0874 ER - TY - GEN A1 - Shrestha, Krishna Prasad A1 - Seidel, Lars A1 - Zeuch, Thomas A1 - Mauß, Fabian T1 - Kinetic Modeling of NOx Formation and Consumption during Methanol and Ethanol Oxidation T2 - Combustion Science and Technology KW - Kinetic Modeling of NOx Formation Y1 - 2019 U6 - https://doi.org/10.1080/00102202.2019.1606804 SN - 1563-521X VL - 191 IS - 9 SP - 1628 EP - 1660 ER - TY - GEN A1 - Netzer, Corinna A1 - Seidel, Lars A1 - Ravet, Frédéric A1 - Mauß, Fabian T1 - Impact of the surrogate formulation on 3D CFD engine knock prediction using detailed chemistry T2 - Fuel N2 - For engine knock prediction, surrogate fuels are often composed of iso-octane and n-heptane since they are the components of the Primary Reference Fuel (PRF). By definition, a PRF has no octane sensitivity (S = RON-MON). However, for a commercial gasoline fuel holds RON > MON and therefor S > 0. More complex surrogates are Toluene Reference Fuels (TRF) and Ethanol containing Toluene Reference Fuels (ETRF). In this work, the impact of the surrogate formulation on the prediction of flame propagation and auto-ignition in the unburnt gases are investigated. The surrogates are composed such that the Research Octane Number is the same. The auto-ignition events ahead of the flame front are predicted using 3D CFD and a combustion model based on the ETRF mechanism by Seidel (2017). The strength of the auto-ignition is determined using the detonation diagram by Bradley and co-workers (2002, 2003). Applying the different surrogates, ignition kernels of different size and reactivity are predicted. The results indicate a dependency on the local temperature history and the low temperature chemistry of the fuel species. The comparison of homogenous constant volume reactor and transient simulations show that the analysis of ignition delay time and octane rating solely from homogenous simulations is not sufficient if the knock tendency of a surrogate in engine simulations needs to be characterized. Y1 - 2019 U6 - https://doi.org/10.1016/j.fuel.2019.115678 SN - 1873-7153 VL - Volume 254 ER - TY - GEN A1 - Franken, Tim A1 - Netzer, Corinna A1 - Mauß, Fabian A1 - Pasternak, Michal A1 - Seidel, Lars A1 - Borg, Anders A1 - Lehtiniemi, Harry A1 - Matrisciano, Andrea A1 - Kulzer, André Casal T1 - Multi-objective optimization of water injection in spark-ignition engines using the stochastic reactor model with tabulated chemistry T2 - International Journal of Engine Research N2 - Water injection is investigated for turbocharged spark-ignition engines to reduce knock probability and enable higher engine efficiency. The novel approach of this work is the development of a simulation-based optimization process combining the advantages of detailed chemistry, the stochastic reactor model and genetic optimization to assess water injection. The fast running quasi-dimensional stochastic reactor model with tabulated chemistry accounts for water effects on laminar flame speed and combustion chemistry. The stochastic reactor model is coupled with the Non-dominated Sorting Genetic Algorithm to find an optimum set of operating conditions for high engine efficiency. Subsequently, the feasibility of the simulation-based optimization process is tested for a three-dimensional computational fluid dynamic numerical test case. The newly proposed optimization method predicts a trade-off between fuel efficiency and low knock probability, which highlights the present target conflict for spark-ignition engine development. Overall, the optimization shows that water injection is beneficial to decrease fuel consumption and knock probability at the same time. The application of the fast running quasi-dimensional stochastic reactor model allows to run large optimization problems with low computational costs. The incorporation with the Non-dominated Sorting Genetic Algorithm shows a well performing multi-objective optimization and an optimized set of engine operating parameters with water injection and high compression ratio is found. KW - Water Injection KW - Genetic Optimization KW - Spark Ignition Engine KW - Stochastic Reactor Model KW - Detailed Chemistry Y1 - 2019 UR - https://journals.sagepub.com/doi/full/10.1177/1468087419857602 U6 - https://doi.org/10.1177/1468087419857602 SN - 2041-3149 VL - 20 IS - 10 SP - 1089 EP - 1100 ER - TY - GEN A1 - Van Treek, Lisa A1 - Lubrano Lavadera, Marco A1 - Konnov, Alexander A. A1 - Seidel, Lars A1 - Mauß, Fabian T1 - Measurements of the laminar burning velocities of ethanol-water-air flames N2 - The laminar burning velocity of ethanol-water-air flames at atmospheric pressure and initial gas temperatures of T = 358 K was measured with the heat flux method. The mixture of ethanol-water-air contained 0%, 10%, 20%, 30% and 40% water by mole and the equivalence ratio (ϕ) range was varied from 0.7 to 1.4. The experiments were compared against predictions using three different kinetic models. Y1 - 2019 UR - https://www.researchgate.net/publication/330635016_Measurements_of_the_laminar_burning_velocities_of_ethanol-water-air_flames N1 - 1st International Conference on Smart Energy Carriers ER - TY - GEN A1 - Shrestha, Krishna Prasad A1 - Seidel, Lars A1 - Zeuch, Thomas A1 - Mauß, Fabian T1 - Modeling for Nitromethane oxidation T2 - 1st International Conference on Smart Energy Carriers Napoli, 2019 N2 - The diminishing availability of conventional fuels and stricter regulations on pollution control and CO2 emission targets have led scientist and engineers to look for alternative fuels. Recently nitromethane has slowly gained interest as alternative fuel over conventional fuel for internal combustion engines. In the past, it was mostly used as rocket propellant or as an explosives [1,2]. Nitromethane is an energetic compound with a wide variety of applications, including its use as a monopropellant, a liquid explosive, a solvent for chemical processing and analysis, and a highperformance fuel additive for internal combustion engines and pulsed detonation engines [3]. The chemical formula of nitromethane is CH3NO2. As the name suggests, the molecule is essentially methane with one of the four hydrogens replaced by a nitro group. In essence, it is the simplest of possible energetic CHON molecules that contain nitro groups, which is why it is often used in reaction studies as a prototype for more complex energetic materials. There is no reliable kinetic model for nitromethane combustion, which is validated over a wide range of experimental conditions. There are a few published studies [4–8] both numerically and experimentally focusing often on a single reactor at very specific conditions. The aim of the present work is to extend our recently published mechanism [9] for syngas, methane and ammonia oxidation to include CH3NO2 as fuel and validate against the available experimental data from the literature. The development and compilation strategy for our mechanism is described in our recent work [9] and this study is conducted in a similar manner. Rates are taken mainly from [7,10–16]. This makes the kinetic model more robust and reliable for combustion modelling. Y1 - 2019 UR - http://logesoft.com/loge-16/wp-content/uploads/2019/01/Abstract_1stICSEC_SMARTCATs_Napoli_Shrestha-et-al_2018-11-28.pdf ER - TY - GEN A1 - León, Larisa A1 - Ruwe, Lena A1 - Moshammer, Kai A1 - Seidel, Lars A1 - Shrestha, Krishna Prasad A1 - Wang, Xiaoxiao A1 - Mauß, Fabian A1 - Kohse-Höinghaus, Katharina A1 - Hansen, Nils T1 - Chemical insights into the larger sooting tendency of 2-methyl-2-butene compared to n-pentane T2 - Combustion and Flame N2 - A comprehensive, chemically detailed mechanism for the combustion of 2-methyl-2-butene and n-pentane is presented to provide insights into the different sooting tendencies of these two structurally different C5 hydrocarbons. A hierarchically assembled mechanism has been developed to specifically target speciation data from low-pressure premixed flames of 2-methyl-2-butene [Ruwe et al., Combust. Flame, 175, 34-46, 2017] and newly measured mole fraction data for a fuel-rich (ɸ=1.8) n-pentane flame, in which species profiles up to phenol were quantified. The partially isomer-resolved chemical composition of this flame was determined using flame-sampling molecular-beam mass spectrometry with single-photon ionization by tunable, synchrotron-generated vacuum-ultraviolet radiation. The presented model, which includes a newly determined, consistent set of the thermochemistry data for the C5 species, presents overall satisfactory capabilities to predict the mole fraction profiles of common combustion intermediates. The analysis of the model predictions revealed the fuel-structure dependencies (i.e. saturated vs. unsaturated and linear vs. branched) of the formation of small aromatic species that are considered as soot precursors. The propensity of the 2-methyl-2-butene flame to form larger concentrations of aromatic species was traced back to the readily available formation routes of several small precursor molecules and the efficient formation of “first aromatic rings” beyond benzene. KW - 2-Methyl-2-butene KW - n-Pentane KW - Laminar premixed flames KW - Molecular-beam mass spectrometry KW - Kinetic modeling KW - PAH formation Y1 - 2019 UR - https://www.sciencedirect.com/science/article/abs/pii/S0010218019302883#! U6 - https://doi.org/10.1016/j.combustflame.2019.06.029 SN - 0010-2180 VL - 208 SP - 182 EP - 197 ER - TY - GEN A1 - Shrestha, Krishna Prasad A1 - Seidel, Lars A1 - Zeuch, Thomas A1 - Mauß, Fabian T1 - Modeling of NOx Formation and Consumption during Oxidation of Small Alcohols T2 - 9th European Combustion Meeting, Proceedings of the European Combustion Meeting N2 - This work presents a newly developed kinetic mechanism extending our recent work (Shrestha et al. [1]) for the oxidation of methanol and ethanol and their fuel interaction with NO x chemistry in jet-stirred reactors, flow reactors, and burner-stabilized premixed flames. The work mainly focuses on fuel interaction with nitrogen chemistry and NO formation in laminar premixed flames. It is found that for methanol oxidation in jet-stirred reactor doping of the fuel blends with NO increase the reactivity of the system by increasing the net production of OH radicals. The increased amount of OH is formed via NO/NO 2 interconversion reaction channels NO+HO 2 ⇋NO 2 +OH, NO 2 +H⇋NO+OH, NO 2 +HO 2 ⇋HONO+O 2, followed by the thermal decomposition of HONO producing NO and OH. In burner-stabilized premixed flames studied here for methanol/air and ethanol/air, NO is mainly formed via the NCN route (CH+N 2 ⇋NCN+H) and minor contribution comes from the NNH route (NNN⇋N 2 +H). Y1 - 2019 UR - https://hal.archives-ouvertes.fr/hal-02334906 ER -