TY - CHAP A1 - Karavaev, Konstantin A1 - Tallarida, Massimo A1 - Schmeißer, Dieter A1 - Zschech, Ehrenfried T1 - In-situ ALD growth of Hafnium oxide films T2 - Verhandlungen der Deutschen Physikalischen Gesellschaft ; Reihe 6, Bd. 43 N2 - We report on a novel system for in-situ atomic layer growth (ALD) of high-k dielectric films. First results were obtained for Hf-oxide samples by using Hf-tetrachloride as precursor and water as oxidizer. We compare the photoelectron spectra of Si2p, O1s and Hf4f of our in-situ prepared films with samples (ex-situ) prepared by industrial ALD reactors and discuss similarities and differences observed in the core level spectra of the various samples by considering the different growth conditions. Y1 - 2008 UR - http://www.dpg-verhandlungen.de/year/2008/conference/berlin/part/ds/session/23/contribution/12 SN - 0420-0195 SP - S. 244 PB - Deutsche Physikalische Gesellschaft CY - Bad Honnef ER - TY - GEN A1 - Dudek, Piotr T. A1 - Lupina, Grzegorz A1 - Kozłowski, Grzegorz A1 - Zaumseil, Peter A1 - Bauer, Jakob A1 - Fursenko, Oksana A1 - Dabrowski, Jarek Marek A1 - Schmidt, R. A1 - Lippert, Gunther A1 - Müssig, Hans-Joachim A1 - Schröder, Thomas A1 - Schmeißer, Dieter A1 - Zschech, Ehrenfried T1 - Atomic-scale engineering of future high-k dynamic random access memory dielectrics: The example of partial Hf substitution by Ti in BaHfO3 T2 - Journal of Vacuum Science and Technology / B Y1 - 2011 SN - 2166-2754 VL - 29 IS - 1 ER - TY - CHAP A1 - Heim, S. A1 - Friedrich, Daniel A1 - Guttmann, P. A1 - Rehbein, S. A1 - Chumakov, Dmytro A1 - Ritz, Y. A1 - Schneider, G. A1 - Schmeißer, Dieter A1 - Zschech, Ehrenfried T1 - Dynamical X-ray Microscopy Study of Stress-Induced Voiding in Cu Interconnects KW - x-ray KW - Microscopy KW - Interconnects Y1 - 2009 UR - http://link.aip.org/link/?APCPCS/1143/20/1 ER - TY - CHAP A1 - Tallarida, Massimo A1 - Karavaev, Konstantin A1 - Schmeißer, Dieter A1 - Zschech, Ehrenfried T1 - HfO2 ALD-growth studied by in situ photoemission T2 - Proceedings of 15th Workshop on Dielectrics in Micoelectronics, Bad Saarow, 23 - 25 June 2008 KW - ald KW - photoemission Y1 - 2008 SP - 289 EP - 290 ER - TY - GEN A1 - Zschech, Ehrenfried A1 - Ho, O. S. A1 - Schmeißer, Dieter A1 - Meyer, Moritz Andreas A1 - Vairagar, A. V. A1 - Schneider, G. A1 - Hauschildt, Meike A1 - Kraatz, Matthias A1 - Sukharev, V. T1 - Geometry and Microstructure Effect on EM-Induced Copper Interconnect Degradation T2 - IEEE Transactions on Device and Materials Reliability KW - Microstructure Y1 - 2009 UR - http://ieeexplore.ieee.org/xpls/icp.jsp?arnumber=4796372 SN - 1530-4388 VL - 9 IS - 1 SP - 20 EP - 30 ER - TY - GEN A1 - Klocek, Jolanta A1 - Kolanek, Krzysztof A1 - Henkel, Karsten A1 - Zschech, Ehrenfried A1 - Schmeißer, Dieter T1 - Influence of the fullerene derivatives and cage polyhedral oligomeric silsesquioxanes on 3-aminopropyltrimethoxysilane based hybrid nanocomposites chemical, morphological and electrical properties T2 - Journal of Physics and Chemistry of Solids N2 - In this study we produced 3-aminopropyltrimethoxysilane based hybrid nanocomposites using fullerene derivative [6,6]–phenyl–C61–butyric acid methyl ester (PCBM) as nanodopants. Additionally, we modified obtained material with incompletely condensed cage polyhedral oligomeric silsesqiuox-anes (POSS) in order to improve its properties. Thin films were deposited by means of the spin-coating method. The films were characterized by atomic force microscopy (AFM), X-ray photoelectron spectroscopy (XPS) and capacitance–voltage (CV) measurements. We observed that a properly chosen PCBM concentration may be a crucial factor to obtain high quality APTMS based films by the spin-coating technique. XPS revealed the presence of the C-NH-C species within POSS containing films indicating chemical interaction between the amino group of APTMS and the POSS molecules. AFM results suggest that at high POSS monomer concentration in the range of 1% the creation of fractal-shaped aggregates takes place. The CV characterization of the samples exhibits a decrease of the APTMS based films dielectric constant due to the POSS and PCBM contribution. The combination of the applied methods delivers complementary information concerning the properties of the analyzed films. KW - low-k KW - fullerene KW - aminopropyltrimethoxysilane KW - silsesqiuoxane KW - X-ray photoelectron spectroscopy (XPS) KW - Atomic force microscopy (AFM) KW - Capacitance voltage (CV) Y1 - 2013 U6 - https://doi.org/10.1016/j.jpcs.2012.08.013 SN - 0022-3697 VL - 74 IS - 1 SP - 135 EP - 145 ER - TY - CHAP A1 - Tallarida, Massimo A1 - Karavaev, Konstantin A1 - Schmeißer, Dieter A1 - Zschech, Ehrenfried T1 - Photoemission and absorption spectroscopy for in situ investigations of the ALD growth T2 - Verhandlungen der Deutschen Physikalischen Gesellschaft, Reihe 6, Bd. 43 N2 - We have investigated the growth of Hf-oxide on Si by means of photoemission and X-ray absorption spectroscopy using synchrotron radiation at Bessy, Berlin. The Hf-oxide layers were grown via atomic layer deposition (ALD) using an in-situ ALD reactor attached to the investigation chamber. The XPS and XAS spectra were measured after every deposition cycle by transferring the sample into the investigation chamber without breaking the vacuum. From the experimental data we have obtained information about the early stages of the Hf-oxide growth, concerning in particular the reactivity of the interface with Si. Due to the possibility to study the layers after every cycle and with different oxidation parameters without exposing them to contaminants, the in situ investigation revealed to be a very important method to understand the growth properties of Hf-oxide. Y1 - 2008 UR - http://www.dpg-verhandlungen.de/year/2008/conference/berlin/part/ds/session/22/contribution/5 SN - 0420-0195 SP - S. 242 PB - Deutsche Physikalische Gesellschaft CY - Bad Honnef ER - TY - CHAP A1 - Hoffmann, Patrick A1 - Schmeißer, Dieter A1 - Engelmann, Hans-Jürgen A1 - Zschech, Ehrenfried A1 - Stegmann, Heiko A1 - Himpsel, Franz J. A1 - Denlinger, Jonathan D. ED - Tsui, Ting Y. T1 - Characterization of chemical bonding in low-k dielectric materials for interconnect isolation: A XAS and EELS Study T2 - Materials, technology and reliability of low-k dielectrics and copper interconnects, symposium held April 18 - 21, 2006, San Francisco, California Y1 - 2006 SN - 978-1-55899-870-5 SP - 55 EP - 62 PB - Materials Research Society CY - Warrendale, Pa. ER - TY - CHAP A1 - Friedrich, Daniel A1 - Michling, Marcel A1 - Klocek, Jolanta A1 - Schmeißer, Dieter A1 - Avdoshenko, Stas A1 - Chumakov, Dmytro A1 - Zschech, Ehrenfried T1 - Study of C60 based films formation by NEXAFS T2 - Verhandlungen der Deutschen Physikalischen Gesellschaft, Reihe 6, Bd. 44 N2 - The C60 fullerenes and some of its -OH, -CF3 and -Cl derivates are candidates for application as ultra-low-k insulators in the semiconductor industry. Future preparation of thin films based on these materials requires the stability of the substituted fullerenes against chemical handling and processing steps. The latter issue was addressed by our NEXAFS studies that were done by synchrotron radiation at the beam line U49/2-PGM2 at BESSY II. Performed were the C K-edge NEXAFS studies in total fluorescence and total electron yield modes. The C60 based films were deposited on silicon by spraying from solutions. The influence of the different substitutional groups with C60 molecules was studied. The data were compared to the reference spectra of a pure C60 film. For C60(OH)24, C60-Cl2 and C60(CF3)12 a variance of the intensity of the π*-resonance as well as shift to higher energies of 0.5 eV (-OH), 0.6 eV (-F), 0.7 eV (-Cl) were observed. The results confirm the necessary stability of the used C60 derivatives and shall be used for optimization of the film deposition chemistry and conditions. Y1 - 2009 SN - 0420-0195 SP - S. 145 PB - Deutsche Physikalische Gesellschaft CY - Bad Honnef ER - TY - GEN A1 - Kraatz, Matthias A1 - Gall, Martin A1 - Zschech, Ehrenfried A1 - Schmeißer, Dieter A1 - Ho, Paul S. T1 - A model for statistical electromigration simulation with dependence on capping layer and Cu microstructure in two dimensions T2 - Computational Materials Science N2 - A model has been developed to simulate electromigration degradation in an interconnect segment in two dimensions using finite differences. The model was deployed on a parallel computer to statistically assess the lifetimes. The simulation takes into account the diffusion paths for electromigration mass transport along the grain boundaries and the capping layer. The microstructure is generated with a Monte Carlo algorithm, using a modified Potts model. Diffusivities along the grain boundaries and the capping layers were applied as multiples of a base diffusivity and were statistically scattered. The simulation results correlate well with electromigration tests. KW - Electromigration KW - Grain growth KW - Computer simulation KW - 2D KW - Copper Interconnects KW - On-chip KW - Statistics KW - Parallel computing Y1 - 2016 U6 - https://doi.org/10.1016/j.commatsci.2016.04.020 SN - 1879-0801 SN - 0927-0256 VL - 120 SP - 29 EP - 35 ER - TY - GEN A1 - Schmeißer, Dieter A1 - Tallarida, Massimo A1 - Henkel, Karsten A1 - Müller, Klaus A1 - Mandal, Dipankar A1 - Chumakov, Dmytro A1 - Zschech, Ehrenfried T1 - Characterization of oxidic and organic materials with synchrotron radiation based XPS and XAS KW - oxidic KW - organic KW - materials KW - synchrotron radiation KW - XPS KW - XAS Y1 - 2009 ER - TY - CHAP A1 - Hoffmann, Patrick A1 - Schmeißer, Dieter A1 - Himpsel, Franz J. A1 - Engelmann, Hans-Jürgen A1 - Zschech, Ehrenfried A1 - Stegmann, Heiko A1 - Denlinger, Jonathan D. T1 - Characterization of Chemical Bonding in Low-K Dielectric Materials for Interconnect Isolation: XAS and EELS Study T2 - Verhandlungen der Deutschen Physikalischen Gesellschaft ; Reihe 6, Bd. 41 N2 - The use of low dielectric constant materials in the on-chip interconnect process reduces interconnect delay, power dissipation and crosstalk noise. In CVD deposited organo-silicate glass (OSG) the substitution of oxygen in SiO2 by methyl groups (-CH3) reduces the permittivity significantly (from 4.0 in SiO2 to 2.6-3.3 in the OSG). However, plasma processing removes C and H containing molecular groups. Therefore, compositional analysis and chemical bonding characterization of structured films with nanometer resolution is necessary. OSG thin films as-deposited and after plasma treatment are studied using XAS and EELS. In both techniques, the fine structure near the C1s edge allows to identify C-H, C-C, and C-O bonds. XAS spectra have been recorded for non-patterned films and EELS spectra for patterned structures. The chemical bonding is compared for as-deposited and plasma-treated low-k materials. The flu-orescence and the electron yield recorded while XAS measurement are compared. Examination of the C 1s near-edge structures reveal a mod-ified bonding of the remaining C atoms in the plasma-treated sample regions. Y1 - 2006 SN - 0420-0195 SP - S. 156 PB - Deutsche Physikalische Gesellschaft CY - Bad Honnef ER - TY - CHAP A1 - Kraatz, Matthias A1 - Zhang, Lijuan A1 - Schmeißer, Dieter A1 - Zschech, Ehrenfried A1 - Ho, Paul S. T1 - Statistical Analysis of Computer-simulated On-Chip Interconnect Electromigration Lifetimes under the Influence of Microstructure and Strengthened Top Interface T2 - Verhandlungen der Deutschen Physikalischen Gesellschaft, Reihe 6, Bd. 46 N2 - We are investigating the statistics of computer-simulated interconnect electromigration (EM) lifetimes with regard to the effects of microstructure and a strengthened top interface. The degradation process of EM once threatened the entire existence of integrated circuit industry in the 1960s and has remained a major reliability concern. Ongoing miniaturization and the introduction of new materials further complicate the task of EM-resistant chip manufacturing. We have developed a simple two-dimensional finite difference simulation that models the mass transport by electromigration along the grain boundaries and the top interface of interconnect segments that allows us to do calculations of void nucleation and growth. A parallel computer simulates hundreds of interconnects simultaneously and statistical analysis becomes feasible. A Monte Carlo grain growth algorithm (a modified Potts version) is applied to model the grain structure of the interconnect segments. We will show that the simulation can be used to compare simulation and experiment qualitatively. Four cases have been studied: interconnect segments with small/large grains and weak/strong top interface. Y1 - 2011 UR - http://www.dpg-verhandlungen.de/year/2011/conference/dresden/part/ds/session/7/contribution/2 SN - 0420-0195 SP - S. 292 PB - Deutsche Physikalische Gesellschaft CY - Bad Honnef ER - TY - CHAP A1 - Kraatz, Matthias A1 - Schmeißer, Dieter A1 - Zschech, Ehrenfried A1 - Ho, Paul S. T1 - Electromigration simulation for on-chip Cu interconnects T2 - Verhandlungen der Deutschen Physikalischen Gesellschaft, Reihe 6, Bd. 44 N2 - We are investigating the influence of copper microstructure on electromigration degradation effects and interconnect lifetimes using computer simulation. The simulation is carried out in three dimensions. For the copper microstructure, a Monte Carlo technique was used to model the Cu grain growth. Different diffusivities where applied to grain boundaries and top interface of the interconnect model according to the qualitative crystallographic orientation of adjacent grains. The grain boundary network and the top interface form the diffusion paths for the electromigration mass transport. Along the diffusion paths, the fluxes of vacancies where calculated including mechanical stress and electromigration driving forces using a finite difference method. Positive flux divergent sites of the FDM lattice are treated as void nucleation sites after a critical vacancy concentration is reached. The resistance increase due to void growth was calculated using a cellular automaton, masking current free regions as quasi voids and adding the resistance of the slices of the lattice normal to the electron flow direction in series. A parallel computing environment was used to generate large numbers of interconnect models in order to obtain a pool of data for statistical analysis of interconnect lifetimes. The results of this analysis will be shown Y1 - 2009 UR - http://www.dpg-verhandlungen.de/year/2009/conference/dresden/part/ds/session/13/contribution/4 SN - 0420-0195 SP - S. 161 PB - Deutsche Physikalische Gesellschaft CY - Bad Honnef ER - TY - GEN A1 - Klocek, Jolanta A1 - Henkel, Karsten A1 - Kolanek, Krzysztof A1 - Zschech, Ehrenfried A1 - Schmeißer, Dieter T1 - Spectroscopic and capacitance-voltage characterization of thin aminopropylmethoxysilane films doped with copper phthalocyanine, tris(dimethylvinylsilyloxy)-POSS and fullerene cages T2 - Applied surface science Y1 - 2012 SN - 0169-4332 VL - 258 IS - 10 SP - 4213 EP - 4221 ER - TY - CHAP A1 - Broczkowska, K. A1 - Klocek, Jolanta A1 - Friedrich, Daniel A1 - Henkel, Karsten A1 - Kolanek, Krzysztof A1 - Urbanowicz, A. A1 - Schmeißer, Dieter A1 - Miller, M. A1 - Zschech, Ehrenfried T1 - Fullerene based materials for ultra-low-k application T2 - International Students and Young Scientists Workshop "Photonics and Microsystems", Szklarska, Poreba, Poland, 25 - 27 June 2010 Y1 - 2010 SN - 978-1-4244-8324-2 SP - 39 EP - 43 PB - IEEE CY - Piscataway, NJ ER - TY - GEN A1 - Klocek, Jolanta A1 - Henkel, Karsten A1 - Kolanek, Krzysztof A1 - Broczkowska, K. A1 - Schmeißer, Dieter A1 - Miller, M. A1 - Zschech, Ehrenfried T1 - Studies of the chemical and electrical properties of fullerene and 3-aminopropyltrimethoxysilane based low-k materials T2 - Thin Solid Films Y1 - 2012 SN - 0040-6090 VL - 520 IS - 7 SP - 2498 EP - 2504 ER - TY - GEN A1 - Klocek, Jolanta A1 - Henkel, Karsten A1 - Kolanek, Krzysztof A1 - Zschech, Ehrenfried A1 - Schmeißer, Dieter T1 - Annealing influence on siloxane based materials incorporated with fullerenes, phthalocyanines and silsesquioxanes T2 - BioNanoScience Y1 - 2012 SN - 2191-1630 VL - 2 IS - 1 SP - 52 EP - 58 ER - TY - GEN A1 - Zagorodniy, Kostyantyn A1 - Chumakov, Dmytro A1 - Täschner, Christine A1 - Lukowiak, Anna A1 - Stegmann, Heiko A1 - Schmeißer, Dieter A1 - Geisler, Holm A1 - Engelmann, Hans-Jürgen A1 - Hermann, Helmut A1 - Zschech, Ehrenfried T1 - Novel Carbon-cage based ultralow-k materials: Modelling and first experiments KW - carbon-cage KW - ultralow-k Y1 - 2008 U6 - https://doi.org/10.1109/TSM.2008.2005396 ER - TY - GEN A1 - Kolanek, Krzysztof A1 - Hermann, Peter A1 - Dudek, Piotr T. A1 - Gotszalk, Teodor A1 - Chumakov, Dmytro A1 - Weisheit, Martin A1 - Hecker, Michael A1 - Zschech, Ehrenfried T1 - Local anodic oxidation by atomic force microscopy for nano-Raman strain measurements on silicon-germanium thin films T2 - Thin Solid Films KW - oxidation KW - microscope KW - measurements KW - thin films Y1 - 2010 SN - 0040-6090 VL - 518 IS - 12 SP - 3267 EP - 3272 ER - TY - GEN A1 - Ho, Paul S. A1 - Zschech, Ehrenfried A1 - Schmeißer, Dieter A1 - Meyer, Moritz Andreas A1 - Huebner, Rene A1 - Hauschildt, Meike A1 - Zhang, Lijuan A1 - Gall, Martin A1 - Kraatz, Matthias T1 - Scaling effects on microstructure and reliability for cu interconnects KW - scaling KW - microstructure KW - interconnects Y1 - 2010 ER - TY - CHAP A1 - Klocek, Jolanta A1 - Friedrich, Daniel A1 - Schmeißer, Dieter A1 - Hecker, Michael A1 - Zschech, Ehrenfried T1 - The stability of C60 and its derivatives upon handling in microsystems technologies T2 - International Students and Young Scientists Workshop "Photonics and Microsystems", 2009, 25 - 27 June 2009, Harz University, Wernigerode, Germany KW - c60 KW - derivatices Y1 - 2009 SN - 978-1-4244-4303-1 SP - 43 EP - 46 PB - IEEE CY - Piscataway, NJ ER - TY - GEN A1 - Zschech, Ehrenfried A1 - Geisler, Holm A1 - Rinderknecht, Jochen A1 - Schneider, Gerd A1 - Spolenak, Ralph A1 - Schmeißer, Dieter T1 - Nano-scale analysis using synchrotron-radiation: Applications in the semiconductor industry T2 - Current nanoscience KW - synchrotron-radiation KW - semiconductor Y1 - 2008 SN - 1573-4137 VL - 4 IS - 3 SP - 256 EP - 266 ER - TY - CHAP A1 - Schmeißer, Dieter A1 - Zheng, Fan A1 - Himpsel, Franz J. A1 - Engelmann, Hans-Jürgen A1 - Zschech, Ehrenfried T1 - Silicate Formation at the Interface of High-k Dielectrics and Si(001) Surfaces Y1 - 2006 ER - TY - JOUR A1 - Schmeißer, Dieter A1 - Zschech, Ehrenfried T1 - Silicate Formation at the Interface of Hf-Oxide and Pr-Oxide as a High-k Dielectric and Si(001) surfaces Y1 - 2006 ER - TY - CHAP A1 - Zschech, Ehrenfried A1 - Engelmann, Hans-Jürgen A1 - Ohsiek, Susanne ED - Kramer, B. T1 - Advanced MOSFET Gate Dielectrics for High-Performance Microprocessors: Materials Selection and Analytical Challenges Y1 - 2005 U6 - https://doi.org/http://dx.doi.org/10.1007/11423256_30 ER - TY - CHAP A1 - Zschech, Ehrenfried A1 - Stegmann, Heiko A1 - Schmeißer, Dieter A1 - Hoffmann, Patrick T1 - Chemical Bonding, Permittivity, and Elastic Properties in Locally Modified Organosilicate Glass Y1 - 2006 ER - TY - GEN A1 - Szyszkiewicz-Warzecha, Krzysztof A1 - Stec, Jakub A1 - Deja, Jan A1 - Łagosz, Artur A1 - Górska, Anna A1 - Kutukova, Kristina A1 - Zschech, Ehrenfried A1 - Filipek, Robert T1 - 3D Multi-Ion Corrosion Model in Hierarchically Structured Cementitious Materials Obtained from Nano-XCT Data T2 - Materials N2 - Corrosion of steel reinforcements in concrete constructions is a worldwide problem. To assess the degradation of rebars in reinforced concrete, an accurate description of electric current, potential and concentrations of various species present in the concrete matrix is necessary. Although the concrete matrix is a heterogeneous porous material with intricate microstructure, mass transport has been treated in a homogeneous material so far, modifying bulk transport coefficients by additional factors (porosity, constrictivity, tortuosity), which led to so-called effective coefficients (e.g., diffusivity). This study presents an approach where the real 3D microstructure of concrete is obtained from high-resolution X-ray computed tomography (XCT), processed to generate a mesh for finite element method (FEM) computations, and finally combined with a multi-species system of transport and electric potential equations. This methodology allows for a more realistic description of ion movements and reactions in the bulk concrete and on the rebar surface and, consequently, a better evaluation of anodic and cathodic currents, ultimately responsible for the loss of reinforcement mass and its location. The results of this study are compared with a state-of-the-art model and numerical calculations for 2D and 3D geometries. KW - 3D corrosion model KW - real 3D concrete microstructure KW - nano-XCT based geometry KW - corrosion of reinforcement KW - multi-ion transport KW - hierarchical concrete structure Y1 - 2023 U6 - https://doi.org/10.3390/ma16145094 SN - 1996-1944 VL - 16 IS - 14 ER - TY - GEN A1 - Lechowski, Bartlomiej A1 - Kutukova, Kristina A1 - Grenzer, Joerg A1 - Panchenko, Iuliana A1 - Krueger, Peter A1 - Clausner, Andre A1 - Zschech, Ehrenfried T1 - Laboratory X-ray Microscopy of 3D Nanostructures in the Hard X-ray Regime Enabled by a Combination of Multilayer X-ray Optics T2 - Nanomaterials N2 - High-resolution imaging of buried metal interconnect structures in advanced microelectronic products with full-field X-ray microscopy is demonstrated in the hard X-ray regime, i.e., at photon energies > 10 keV. The combination of two multilayer optics—a side-by-side Montel (or nested Kirkpatrick–Baez) condenser optic and a high aspect-ratio multilayer Laue lens—results in an asymmetric optical path in the transmission X-ray microscope. This optics arrangement allows the imaging of 3D nanostructures in opaque objects at a photon energy of 24.2 keV (In-Kα X-ray line). Using a Siemens star test pattern with a minimal feature size of 150 nm, it was proven that features < 150 nm can be resolved. In-Kα radiation is generated from a Ga-In alloy target using a laboratory X-ray source that employs the liquid-metal-jet technology. Since the penetration depth of X-rays into the samples is significantly larger compared to 8 keV photons used in state-of-the-art laboratory X-ray microscopes (Cu-Kα radiation), 3D-nanopattered materials and structures can be imaged nondestructively in mm to cm thick samples. This means that destructive de-processing, thinning or cross-sectioning of the samples are not needed for the visualization of interconnect structures in microelectronic products manufactured using advanced packaging technologies. The application of laboratory transmission X-ray microscopy in the hard X-ray regime is demonstrated for Cu/Cu6Sn5/Cu microbump interconnects fabricated using solid–liquid interdiffusion (SLID) bonding. KW - X-ray microscopy KW - high-resolution radiography KW - nanostructure KW - advanced packaging Y1 - 2024 U6 - https://doi.org/10.3390/nano14020233 SN - 2079-4991 VL - 14 IS - 2 ER - TY - GEN A1 - Kutukova, Kristina A1 - Lechowski, Bartlomiej A1 - Grenzer, Joerg A1 - Krueger, Peter A1 - Clausner, André A1 - Zschech, Ehrenfried T1 - Laboratory High-Contrast X-ray Microscopy of Copper Nanostructures Enabled by a Liquid-Metal-Jet X-ray Source T2 - Nanomaterials N2 - High-resolution imaging of Cu/low-k on-chip interconnect stacks in advanced micro-electronic products is demonstrated using full-field transmission X-ray microscopy (TXM). The comparison of two lens-based laboratory X-ray microscopes that are operated at two different photon energies, 8.0 keV and 9.2 keV, shows a contrast enhancement for imaging of copper nanostructures embedded in insulating organosilicate glass of a factor of 5 if 9.2 keV photons are used. Photons with this energy (Ga-Kα radiation) are generated from a Ga-containing target of a laboratory X-ray source applying the liquid-metal-jet technology. The 5 times higher contrast compared to the use of Cu-Kα radiation (8.0 keV photon energy) from a rotating anode X-ray source is caused by the fact that the energy of the Ga-Kα emission line is slightly higher than that of the Cu-K absorption edge (9.0 keV photon energy). The use of Ga-Kα radiation is of particular advantage for imaging of copper interconnects with dimensions from several 100 nm down to several 10 nm in a Cu/SiO2 or Cu/low-k backend-of-line stack. Physical failure analysis and reliability engineering in the semiconductor industry will benefit from high-contrast X-ray images of sub-µm copper structures in microchips. KW - X-ray microscopy KW - radiography KW - image contrast KW - nanostructure KW - physical failure analysis KW - copper interconnects Y1 - 2024 U6 - https://doi.org/10.3390/nano14050448 SN - 2079-4991 VL - 14 IS - 5 ER -