TY - GEN A1 - Vacca, Antonino A1 - Bargende, Michael A1 - Chiodi, Marco A1 - Netzer, Corinna A1 - Gern, Maike Sophie A1 - Kauf, Georg Malte A1 - Kulzer, André Casal A1 - Franken, Tim T1 - Analysis of Water Injection Strategies to Exploit the Thermodynamic Effects of Water in Gasoline Engines by Means of a 3D-CFD Virtual Test Bench N2 - CO2 emission constraints taking effect from 2020 lead to further investigations of technologies to lower knock sensitivity of gasoline engines, main limiting factor to increase engine efficiency and thus reduce fuel consumption. Moreover the RDE cycle demands for higher power operation, where fuel enrichment is needed for component protection. To achieve high efficiency, the engine should be run at stoichiometric conditions in order to have better emission control and reduce fuel consumption. Among others, water injection is a promising technology to improve engine combustion efficiency, by mainly reducing knock sensitivity and to keep high conversion rates of the TWC over the whole engine map. The comprehension of multiple thermodynamic effects of water injection through 3D-CFD simulations and their exploitation to enhance the engine combustion efficiency is the main purpose of the analysis. As basis for the research a single cylinder engine derived from a 1l turbocharged 3-cylinders engine is used to evaluate indirect and direct water injection. The entire engine flow field is reproduced and analyzed with 3D-CFD simulations and numerical models are employed to separate the influence of chemical and thermodynamic properties. Measurements are performed with different injectors for indirect/direct water injection in the single-cylinder engine in order to assess water break-up, wall wetting, spray interaction and penetration. Several injection strategies, such as varying start of injection, injection pressure, and water to fuel ratio, are tested at the single-cylinder engine test bench. Detailed gas phase chemistry is employed to link flame front speed with water concentration and knocking occurrence. These results are correlated with the 3D-CFD simulation of mixture formation, in-cylinder flow and water distribution for two different operating points (part load and maximum power) in order to study water behavior, with focus on the evaporation process, in-cylinder pressure and temperature profile, as well as the combustion development, during multiple engine cycles. KW - Water Injection KW - Computational Fluid Dynamics KW - Simulation KW - Virtual Test Bench KW - Thermodynamics Y1 - 2019 UR - https://saemobilus.sae.org/content/2019-24-0102 U6 - https://doi.org/10.4271/2019-24-0102 PB - SAE International CY - Neapel ER - TY - GEN A1 - Rossi, Edoardo A1 - Bargende, Michael A1 - Kulzer, André Casal A1 - Chiodi, Marco A1 - Massoud, Ehab A1 - Shrestha, Krishna Prasad A1 - Mauß, Fabian T1 - Analysis of the applicability of Water Injection in Combination with an eFuel for Knock Mitigation and Improved Engine Efficiency T2 - SAE Technical Paper N2 - The development of future gasoline engines is dominated by the study of new technologies aimed at reducing the engine negative environmental impact and increase its thermal efficiency. One common trend is to develop smaller engines able to operate in stoichiometric conditions across the whole engine map for better efficiency, lower fuel consumption, and optimal conversion rate of the three-way catalyst (TWC). Water injection is one promising technique, as it significantly reduces the engine knock tendency and avoids fuel enrichment for exhaust temperature mitigation at high power operation. With the focus on reducing the carbon footprint of the automotive sector, another vital topic of research is the investigation of new alternative CO2-neutral fuels or so-called eFuels. Several studies have already shown how these new synthetic fuels can be produced by exploiting renewable energy sources and can significantly reduce engine emissions. This work is part of the FVV project number 1367, “Water Injection in Spark-Ignition Engines II”, which investigates the coexistence of two different engine technologies that heads towards the same direction of sustainability of the internal combustion engine: water injection and eFuels. The goal is to assess the advantages that the adoption of an eFuel in combination with water injection strategies can bring, with respect to the same strategies applied in combination with commercial gasoline. Several water injection strategies, including direct water injection, indirect water injection, injection timing, and pressure variations, are considered for a better understanding of the benefits brought by the combination of an eFuel with water injection. For this purpose, experimental tests and 3D-CFD engine simulations have been performed. The physical properties of the investigated eFuel have been experimentally measured for accurate modelling in the simulation environment, and the thermodynamic properties have been evaluated utilizing detailed chemistry calculations. Y1 - 2022 U6 - https://doi.org/10.4271/2022-37-0019 SN - 2688-3627 SN - 0148-7191 ER -