TY - GEN A1 - Obrosov, Aleksei A1 - Sutygina, Alina A1 - Volinsky, Alex A. A1 - Manakhov, Anton A1 - Weiß, Sabine A1 - Kashkarov, Egor B. T1 - Effect of Hydrogen Exposure on Mechanical and Tribological Behavior of CrₓN Coatings Deposited at Different Pressures on IN718 T2 - Materials N2 - In the current study, the properties of the CrₓN coatings deposited on the Inconel 718 superalloy using direct current reactive magnetron sputtering are investigated. The influence of working pressure on the microstructure, mechanical, and tribological properties of the CrₓN coatings before and after high-temperature hydrogen exposure is studied. The cross-sectional scanning electron micrographs indicate the columnar structure of the coatings, which changes from dense and compact columns to large columns with increasing working pressure. The Cr/N ratio increases from 1.4 to 1.9 with increasing working pressure from 300 to 900 mPa, respectively. X-ray diffraction analysis reveals a change from mixed hcp-Cr₂N and fcc-CrN structure to approximately stoichiometric Cr₂N phase. After gas-phase hydrogenation, the coating deposited at 300 mPa exhibits the lowest hydrogen absorption at 600 °C of all investigated coatings. The results indicate that the dense mixed cubic and hexagonal structure is preferential for hydrogen permeation resistance due to the presence of cubic phase with higher packing density in comparison to the hexagonal structure. After hydrogenation, no changes in phase composition were observed; however, a small amount of hydrogen is accumulated in the coatings. An increase of coating hardness and elastic modulus was observed after hydrogen exposure. Tribological tests reveal that hydrogenation leads to a decrease of the friction coefficient up to 20%–30%. The best value of 0.25 was reached for hydrogen exposed CrₓN coating deposited at 300 mPa. KW - CrₓN coatings KW - PVD KW - hydrogenation KW - tribology KW - mechanical properties KW - GDOES Y1 - 2017 UR - http://www.mdpi.com/1996-1944/10/5/563/htm U6 - https://doi.org/10.3390/ma10050563 SN - 1996-1944 VL - 10 IS - 5 SP - 563 ER - TY - GEN A1 - Obrosov, Aleksei A1 - Sutygina, Alina A1 - Manakhov, Anton A1 - Bolz, Sebastian A1 - Weiß, Sabine A1 - Kashkarov, Egor B. T1 - Oxidation Behavior of Zr–1Nb Corroded in Air at 400 °C after Plasma Immersion Titanium Implantation T2 - Metals N2 - In this paper, the influence of plasma immersion titanium implantation into the zirconium alloy Zr-1Nb on the oxidation behavior at 400 °C for 5, 24, 72, and 240 h in air under normal atmospheric pressure (101.3 kPa) was shown. The influence of implantation on the protective properties of the modified layer was shown. The valence of the oxides before and after implantation was analyzed by means of X-ray photoelectron spectroscopy (XPS). Grazing incidence X-ray diffraction (GIXRD) was carried out to examine the phase composition after titanium ion implantation and oxidation. Differential scanning calorimetry (DSC) revealed that titanium implantation exhibited effects of stabilizing the β phase. The formation of the t-ZrO2 and m-ZrO2 was observed during the oxidation of the as-received and modified Zr-1Nb. The measurement of weight gain showed an improvement in oxidation resistance of Ti implanted Zr-1Nb at the oxidation up to 24 h when compared with that of the as-received Zr-1Nb. However, at longer oxidation cycle the oxidation rate of Ti-implanted zirconium alloy is the same with the as-received alloy, which attributed to the layer thickness. Nevertheless, the corrosion of the Ti-implanted alloy is more uniform, while a local corrosion and cracks was detected on the surface of the as-received alloy. KW - zirconium alloy KW - titanium KW - ion implantation KW - PIII KW - oxidation KW - DSC KW - XPS KW - surface morphology KW - X-ray diffraction Y1 - 2018 UR - http://www.mdpi.com/2075-4701/8/1/27/htm U6 - https://doi.org/10.3390/met8010027 SN - 2075-4701 VL - 8 IS - 1 ER - TY - GEN A1 - Solovieva, Anastasiya A1 - Miroshnichenko, Svetlana A1 - Kovalskii, Andrey A1 - Permyakova, Elizaveta A1 - Popov, Zakhar A1 - Dvořáková, Eva A1 - Kiryukhantsev-Korneev, Philip A1 - Obrosov, Aleksei A1 - Polčak, Josef A1 - Zajíčková, Lenka A1 - Shtansky, Dmitry V. A1 - Manakhov, Anton T1 - Immobilization of Platelet-Rich Plasma onto COOH Plasma-Coated PCL Nanofibers Boost Viability and Proliferation of Human Mesenchymal Stem Cells T2 - Polymers N2 - The scaffolds made of polycaprolactone (PCL) are actively employed in different areas of biology and medicine, especially in tissue engineering. However, the usage of unmodified PCL is significantly restricted by the hydrophobicity of its surface, due to the fact that its inert surface hinders the adhesion of cells and the cell interactions on PCL surface. In this work, the surface of PCL nanofibers is modified by Ar/CO2/C2H4 plasma depositing active COOH groups in the amount of 0.57 at % that were later used for the immobilization of platelet-rich plasma (PRP). The modification of PCL nanofibers significantly enhances the viability and proliferation (by hundred times) of human mesenchymal stem cells, and decreases apoptotic cell death to a normal level. According to X-ray photoelectron spectroscopy (XPS), after immobilization of PRP, up to 10.7 at % of nitrogen was incorporated into the nanofibers surface confirming the grafting of proteins. Active proliferation and sustaining the cell viability on nanofibers with immobilized PRP led to an average number of cells of 258 ± 12.9 and 364 ± 34.5 for nanofibers with ionic and covalent bonding of PRP, respectively. Hence, our new method for the modification of PCL nanofibers with PRP opens new possibilities for its application in tissue engineering. KW - polycaprolactone KW - nanofibers KW - COOH plasma KW - platelet-rich plasma KW - cell viability KW - PRP immobilization Y1 - 2017 UR - http://www.mdpi.com/2073-4360/9/12/736/htm U6 - https://doi.org/10.3390/polym9120736 SN - 2073-4360 VL - 9 IS - 12 ER - TY - GEN A1 - Kashkarov, Egor B. A1 - Nikitenkov, Nikolay A1 - Sutygina, Alina A1 - Obrosov, Aleksei A1 - Manakhov, Anton A1 - Polčak, Josef A1 - Weiß, Sabine T1 - Hydrogen absorption by Ti-implanted Zr-1Nb alloy T2 - International journal of hydrogen energy N2 - This paper describes the hydrogenation behavior of Zr-1Nb alloy Ti-implanted by plasma immersion ion implantation (PIII). Hydrogen sorption kinetics of the Ti-modified alloy was investigated under gas-phase hydrogenation at 400 °C for 1 h. The influence of implantation time on the protective properties of the modified layer was shown. The lowest hydrogen absorption as well as the highest hydrogen trapping efficiency was achieved after PIII for 30 min. The main contribution to the reduction of hydrogen permeation is the formation of an oxide layer consisting of mixed TiO2 and ZrO2 on the modified surface of the alloy. X-ray photoelectron spectroscopy (XPS) revealed that PIII titanium oxide exists on the surface in the form of TiO2, which transforms to mixed Ti2O3 and TiO2 after hydrogenation. The thickness of the modified layer increases with implantation time that improves the efficiency of hydrogen trapping. All the absorbed hydrogen is gradually distributed in the modified layer and no hydrides are formed after hydrogenation in Ti-modified Zr-1Nb for 15 and 30 min. KW - Zirconium KW - Titanium implantation KW - Hydrogenation KW - X-ray photoelectron spectroscopy KW - Glow discharge optical emission spectroscopy KW - X-ray diffraction Y1 - 2018 UR - https://www.sciencedirect.com/science/article/pii/S0360319917346359 U6 - https://doi.org/10.1016/j.ijhydene.2017.12.003 SN - 0360-3199 VL - 43 IS - 4 SP - 2484 EP - 2491 ER -