TY - GEN A1 - Gern, Maike Sophie A1 - Kauf, Georg Malte A1 - Vacca, Antonino A1 - Franken, Tim A1 - Kulzer, André Casal T1 - Ganzheitliche Methode zur Bewertung der Wassereinspritzung T2 - MTZ - Motortechnische Zeitschrift N2 - Die künftige Effizienzsteigerung bei Ottomotoren mit Direkteinspritzung sowie die Reduktion von gas- und partikelförmigen Emissionen erfordern innovative Ansätze. Durch die neue RDEGesetzgebung für leichte Kraftfahrzeuge verschiebt sich der Fokus hin zu dynamischen Testzyklen mit 12 % mehr Hochlastbetriebspunkten im Vergleich zum WLTC (Worldwide harmonized Light Duty Test Cycle). Die Steigerung des Mitteldrucks bei Ottomotoren führt zu einem effizienten Betrieb, der jedoch durch das Risiko irregulärer Verbrennung und hohen Abgastemperaturen limitiert ist. Durch den Einsatz von Wassereinspritzung können sowohl die Klopfneigung als auch die Abgastemperatur reduziert werden, was den Schutz der Abgasnachbehandlungskomponenten bei gleichzeitiger Wirkungsgradsteigerung ermöglicht. Im Rahmen des FVV-Projekts „Wassereinspritzung bei Ottomotoren“ wird der Einfluss der NiederdruckWassereinspritzung (NDWE) und Hochdruck-Wassereinspritzung (HDWE) untersucht. Insbesondere die Auswirkungen auf Gemischbildung, Verbrennung und Abgasnachbehandlung werden durch die Vernetzung von Experiment und Simulation analysiert. KW - Water Injection KW - Wassereinspritzung KW - Gasoline KW - Simulation KW - Efficiency Y1 - 2019 U6 - https://doi.org/10.1007/s35146-019-0070-x SN - 2192-8843 VL - 80 IS - 7-8 SP - 124 EP - 129 ER - TY - GEN A1 - Franken, Tim A1 - Netzer, Corinna A1 - Mauß, Fabian A1 - Pasternak, Michal A1 - Seidel, Lars A1 - Borg, Anders A1 - Lehtiniemi, Harry A1 - Matrisciano, Andrea A1 - Kulzer, André Casal T1 - Multi-objective optimization of water injection in spark-ignition engines using the stochastic reactor model with tabulated chemistry T2 - International Journal of Engine Research N2 - Water injection is investigated for turbocharged spark-ignition engines to reduce knock probability and enable higher engine efficiency. The novel approach of this work is the development of a simulation-based optimization process combining the advantages of detailed chemistry, the stochastic reactor model and genetic optimization to assess water injection. The fast running quasi-dimensional stochastic reactor model with tabulated chemistry accounts for water effects on laminar flame speed and combustion chemistry. The stochastic reactor model is coupled with the Non-dominated Sorting Genetic Algorithm to find an optimum set of operating conditions for high engine efficiency. Subsequently, the feasibility of the simulation-based optimization process is tested for a three-dimensional computational fluid dynamic numerical test case. The newly proposed optimization method predicts a trade-off between fuel efficiency and low knock probability, which highlights the present target conflict for spark-ignition engine development. Overall, the optimization shows that water injection is beneficial to decrease fuel consumption and knock probability at the same time. The application of the fast running quasi-dimensional stochastic reactor model allows to run large optimization problems with low computational costs. The incorporation with the Non-dominated Sorting Genetic Algorithm shows a well performing multi-objective optimization and an optimized set of engine operating parameters with water injection and high compression ratio is found. KW - Water Injection KW - Genetic Optimization KW - Spark Ignition Engine KW - Stochastic Reactor Model KW - Detailed Chemistry Y1 - 2019 UR - https://journals.sagepub.com/doi/full/10.1177/1468087419857602 U6 - https://doi.org/10.1177/1468087419857602 SN - 2041-3149 VL - 20 IS - 10 SP - 1089 EP - 1100 ER - TY - GEN A1 - Franken, Tim A1 - Mauß, Fabian A1 - Seidel, Lars A1 - Gern, Maike Sophie A1 - Kauf, Malte A1 - Matrisciano, Andrea A1 - Kulzer, Andre Casal T1 - Gasoline engine performance simulation of water injection and low-pressure exhaust gas recirculation using tabulated chemistry T2 - International Journal of Engine Research N2 - This work presents the assessment of direct water injection in spark-ignition engines using single cylinder experiments and tabulated chemistry-based simulations. In addition, direct water injection is compared with cooled low-pressure exhaust gas recirculation at full load operation. The analysis of the two knock suppressing and exhaust gas cooling methods is performed using the quasi-dimensional stochastic reactor model with a novel dual fuel tabulated chemistry model. To evaluate the characteristics of the autoignition in the end gas, the detonation diagram developed by Bradley and coworkers is applied. The single cylinder experiments with direct water injection outline the decreasing carbon monoxide emissions with increasing water content, while the nitrogen oxide emissions indicate only a minor decrease. The simulation results show that the engine can be operated at l = 1 at full load using water–fuel ratios of up to 60% or cooled low-pressure exhaust gas recirculation rates of up to 30%. Both technologies enable the reduction of the knock probability and the decrease in the catalyst inlet temperature to protect the aftertreatment system components. The strongest exhaust temperature reduction is found with cooled low-pressure exhaust gas recirculation. With stoichiometric air–fuel ratio and water injection, the indicated efficiency is improved to 40% and the carbon monoxide emissions are reduced. The nitrogen oxide concentrations are increased compared to the fuel-rich base operating conditions and the nitrogen oxide emissions decrease with higher water content. With stoichiometric air–fuel ratio and exhaust gas recirculation, the indicated efficiency is improved to 43% and the carbon monoxide emissions are decreased. Increasing the exhaust gas recirculation rate to 30% drops the nitrogen oxide emissions below the concentrations of the fuel-rich base operating conditions. KW - Water Injection KW - Exhaust Gas Recirculation KW - Efficiency KW - Spark Ignition Engine KW - Stochastic Reactor Model KW - Emissions Y1 - 2020 UR - https://journals.sagepub.com/doi/abs/10.1177/1468087420933124 U6 - https://doi.org/10.1177/1468087420933124 SN - 2041-3149 SN - 1468-0874 VL - 21 IS - 10 SP - 1857 EP - 1877 ER - TY - GEN A1 - Rossi, Edoardo A1 - Bargende, Michael A1 - Kulzer, André Casal A1 - Chiodi, Marco A1 - Massoud, Ehab A1 - Shrestha, Krishna Prasad A1 - Mauß, Fabian T1 - Analysis of the applicability of Water Injection in Combination with an eFuel for Knock Mitigation and Improved Engine Efficiency T2 - SAE Technical Paper N2 - The development of future gasoline engines is dominated by the study of new technologies aimed at reducing the engine negative environmental impact and increase its thermal efficiency. One common trend is to develop smaller engines able to operate in stoichiometric conditions across the whole engine map for better efficiency, lower fuel consumption, and optimal conversion rate of the three-way catalyst (TWC). Water injection is one promising technique, as it significantly reduces the engine knock tendency and avoids fuel enrichment for exhaust temperature mitigation at high power operation. With the focus on reducing the carbon footprint of the automotive sector, another vital topic of research is the investigation of new alternative CO2-neutral fuels or so-called eFuels. Several studies have already shown how these new synthetic fuels can be produced by exploiting renewable energy sources and can significantly reduce engine emissions. This work is part of the FVV project number 1367, “Water Injection in Spark-Ignition Engines II”, which investigates the coexistence of two different engine technologies that heads towards the same direction of sustainability of the internal combustion engine: water injection and eFuels. The goal is to assess the advantages that the adoption of an eFuel in combination with water injection strategies can bring, with respect to the same strategies applied in combination with commercial gasoline. Several water injection strategies, including direct water injection, indirect water injection, injection timing, and pressure variations, are considered for a better understanding of the benefits brought by the combination of an eFuel with water injection. For this purpose, experimental tests and 3D-CFD engine simulations have been performed. The physical properties of the investigated eFuel have been experimentally measured for accurate modelling in the simulation environment, and the thermodynamic properties have been evaluated utilizing detailed chemistry calculations. Y1 - 2022 U6 - https://doi.org/10.4271/2022-37-0019 SN - 2688-3627 SN - 0148-7191 ER -