TY - CHAP A1 - Franken, Tim A1 - Netzer, Corinna A1 - Pasternak, Michal A1 - Mauß, Fabian A1 - Seidel, Lars A1 - Matrisciano, Andrea A1 - Borg, Anders A1 - Lehtiniemi, Harry A1 - Kulzer, André Casal T1 - Assessment of Water Injection in a SI Engine using a Fast Running Detailed Chemistry Based Combustion Model T2 - Symposium of Combustion Control 2018, Aachen KW - Assessment of Water Injection Y1 - 2018 UR - https://www.researchgate.net/publication/326059620 UR - http://logesoft.com/loge-16/wp-content/uploads/2018/07/2018-06-19-SCC_-1.pdf CY - Aachen ER - TY - GEN A1 - Franken, Tim A1 - Netzer, Corinna A1 - Pasternak, Michal A1 - Mauß, Fabian A1 - Seidel, Lars A1 - Matrisciano, Andrea A1 - Borg, Anders A1 - Lehtiniemi, Harry A1 - Kulzer, André Casal T1 - Simulation of Spark-Ignited Engines with Water Injection using the Stochastic Reactor Model, 37th International Symposium on Combustion Y1 - 2018 UR - https://www.researchgate.net/publication/328265636 ER - TY - GEN A1 - Vacca, Antonino A1 - Bargende, Michael A1 - Chiodi, Marco A1 - Netzer, Corinna A1 - Gern, Maike Sophie A1 - Kauf, Georg Malte A1 - Kulzer, André Casal A1 - Franken, Tim T1 - Analysis of Water Injection Strategies to Exploit the Thermodynamic Effects of Water in Gasoline Engines by Means of a 3D-CFD Virtual Test Bench N2 - CO2 emission constraints taking effect from 2020 lead to further investigations of technologies to lower knock sensitivity of gasoline engines, main limiting factor to increase engine efficiency and thus reduce fuel consumption. Moreover the RDE cycle demands for higher power operation, where fuel enrichment is needed for component protection. To achieve high efficiency, the engine should be run at stoichiometric conditions in order to have better emission control and reduce fuel consumption. Among others, water injection is a promising technology to improve engine combustion efficiency, by mainly reducing knock sensitivity and to keep high conversion rates of the TWC over the whole engine map. The comprehension of multiple thermodynamic effects of water injection through 3D-CFD simulations and their exploitation to enhance the engine combustion efficiency is the main purpose of the analysis. As basis for the research a single cylinder engine derived from a 1l turbocharged 3-cylinders engine is used to evaluate indirect and direct water injection. The entire engine flow field is reproduced and analyzed with 3D-CFD simulations and numerical models are employed to separate the influence of chemical and thermodynamic properties. Measurements are performed with different injectors for indirect/direct water injection in the single-cylinder engine in order to assess water break-up, wall wetting, spray interaction and penetration. Several injection strategies, such as varying start of injection, injection pressure, and water to fuel ratio, are tested at the single-cylinder engine test bench. Detailed gas phase chemistry is employed to link flame front speed with water concentration and knocking occurrence. These results are correlated with the 3D-CFD simulation of mixture formation, in-cylinder flow and water distribution for two different operating points (part load and maximum power) in order to study water behavior, with focus on the evaporation process, in-cylinder pressure and temperature profile, as well as the combustion development, during multiple engine cycles. KW - Water Injection KW - Computational Fluid Dynamics KW - Simulation KW - Virtual Test Bench KW - Thermodynamics Y1 - 2019 UR - https://saemobilus.sae.org/content/2019-24-0102 U6 - https://doi.org/10.4271/2019-24-0102 PB - SAE International CY - Neapel ER - TY - GEN A1 - Franken, Tim A1 - Netzer, Corinna A1 - Mauß, Fabian A1 - Pasternak, Michal A1 - Seidel, Lars A1 - Borg, Anders A1 - Lehtiniemi, Harry A1 - Matrisciano, Andrea A1 - Kulzer, André Casal T1 - Multi-objective optimization of water injection in spark-ignition engines using the stochastic reactor model with tabulated chemistry T2 - International Journal of Engine Research N2 - Water injection is investigated for turbocharged spark-ignition engines to reduce knock probability and enable higher engine efficiency. The novel approach of this work is the development of a simulation-based optimization process combining the advantages of detailed chemistry, the stochastic reactor model and genetic optimization to assess water injection. The fast running quasi-dimensional stochastic reactor model with tabulated chemistry accounts for water effects on laminar flame speed and combustion chemistry. The stochastic reactor model is coupled with the Non-dominated Sorting Genetic Algorithm to find an optimum set of operating conditions for high engine efficiency. Subsequently, the feasibility of the simulation-based optimization process is tested for a three-dimensional computational fluid dynamic numerical test case. The newly proposed optimization method predicts a trade-off between fuel efficiency and low knock probability, which highlights the present target conflict for spark-ignition engine development. Overall, the optimization shows that water injection is beneficial to decrease fuel consumption and knock probability at the same time. The application of the fast running quasi-dimensional stochastic reactor model allows to run large optimization problems with low computational costs. The incorporation with the Non-dominated Sorting Genetic Algorithm shows a well performing multi-objective optimization and an optimized set of engine operating parameters with water injection and high compression ratio is found. KW - Water Injection KW - Genetic Optimization KW - Spark Ignition Engine KW - Stochastic Reactor Model KW - Detailed Chemistry Y1 - 2019 UR - https://journals.sagepub.com/doi/full/10.1177/1468087419857602 U6 - https://doi.org/10.1177/1468087419857602 SN - 2041-3149 VL - 20 IS - 10 SP - 1089 EP - 1100 ER - TY - GEN A1 - Franken, Tim A1 - Seidel, Lars A1 - Matrisciano, Andrea A1 - Mauß, Fabian A1 - Kulzer, Andre Casal A1 - Schuerg, Frank T1 - Analysis of the Water Addition Efficiency on Knock Suppression for Different Octane Ratings T2 - SAE World Congress N2 - Water injection can be applied to spark ignited gasoline engines to increase the Knock Limit Spark Advance and improve the thermal efficiency. The Knock Limit Spark Advance potential of 6 °CA to 11 °CA is shown by many research groups for EN228 gasoline fuel using experimental and simulation methods. The influence of water is multi-layered since it reduces the in-cylinder temperature by vaporization and higher heat capacity of the fresh gas, it changes the chemical equilibrium in the end gas and increases the ignition delay and decreases the laminar flame speed. The aim of this work is to extend the analysis of water addition to different octane ratings. The simulation method used for the analysis consists of a detailed reaction scheme for gasoline fuels, the Quasi-Dimensional Stochastic Reactor Model and the Detonation Diagram. The detailed reaction scheme is used to create the dual fuel laminar flame speed and combustion chemistry look-up tables. The Detonation Diagram is used as a novel approach in the Quasi-Dimensional Stochastic Reactor Model to evaluate the auto-ignition characteristic in the end gas and determine if it is a harmless deflagration or developing detonation. First, the Quasi-Dimensional Stochastic Reactor Model is trained for three engine operating points and a RON95 E10 fuel. Its performance is evaluated based on experimental results of a single cylinder research engine. Subsequently, different spark timings and water-fuel ratios are investigated for different Primary Reference Fuels. The results outline that water addition can effectively reduce the strength of auto-ignition in the end gas for different Primary Reference Fuels. Thereby, it can be stated that the reduction of the auto-ignition strength through water addition by 50 – 80 % water-fuel ratio for high octane number fuels corresponds to the spark timing delay of 6 °CA or an increase of research octane number by 10 points. KW - Gasoline KW - Knock KW - Water KW - Engines KW - Combustion KW - Simulation Y1 - 2020 U6 - https://doi.org/10.4271/2020-01-0551 SN - 2688-3627 SN - 0148-7191 ER - TY - GEN A1 - Franken, Tim A1 - Mauß, Fabian A1 - Seidel, Lars A1 - Gern, Maike Sophie A1 - Kauf, Malte A1 - Matrisciano, Andrea A1 - Kulzer, Andre Casal T1 - Gasoline engine performance simulation of water injection and low-pressure exhaust gas recirculation using tabulated chemistry T2 - International Journal of Engine Research N2 - This work presents the assessment of direct water injection in spark-ignition engines using single cylinder experiments and tabulated chemistry-based simulations. In addition, direct water injection is compared with cooled low-pressure exhaust gas recirculation at full load operation. The analysis of the two knock suppressing and exhaust gas cooling methods is performed using the quasi-dimensional stochastic reactor model with a novel dual fuel tabulated chemistry model. To evaluate the characteristics of the autoignition in the end gas, the detonation diagram developed by Bradley and coworkers is applied. The single cylinder experiments with direct water injection outline the decreasing carbon monoxide emissions with increasing water content, while the nitrogen oxide emissions indicate only a minor decrease. The simulation results show that the engine can be operated at l = 1 at full load using water–fuel ratios of up to 60% or cooled low-pressure exhaust gas recirculation rates of up to 30%. Both technologies enable the reduction of the knock probability and the decrease in the catalyst inlet temperature to protect the aftertreatment system components. The strongest exhaust temperature reduction is found with cooled low-pressure exhaust gas recirculation. With stoichiometric air–fuel ratio and water injection, the indicated efficiency is improved to 40% and the carbon monoxide emissions are reduced. The nitrogen oxide concentrations are increased compared to the fuel-rich base operating conditions and the nitrogen oxide emissions decrease with higher water content. With stoichiometric air–fuel ratio and exhaust gas recirculation, the indicated efficiency is improved to 43% and the carbon monoxide emissions are decreased. Increasing the exhaust gas recirculation rate to 30% drops the nitrogen oxide emissions below the concentrations of the fuel-rich base operating conditions. KW - Water Injection KW - Exhaust Gas Recirculation KW - Efficiency KW - Spark Ignition Engine KW - Stochastic Reactor Model KW - Emissions Y1 - 2020 UR - https://journals.sagepub.com/doi/abs/10.1177/1468087420933124 U6 - https://doi.org/10.1177/1468087420933124 SN - 2041-3149 SN - 1468-0874 VL - 21 IS - 10 SP - 1857 EP - 1877 ER - TY - GEN A1 - Rossi, Edoardo A1 - Bargende, Michael A1 - Kulzer, André Casal A1 - Chiodi, Marco A1 - Massoud, Ehab A1 - Shrestha, Krishna Prasad A1 - Mauß, Fabian T1 - Analysis of the applicability of Water Injection in Combination with an eFuel for Knock Mitigation and Improved Engine Efficiency T2 - SAE Technical Paper N2 - The development of future gasoline engines is dominated by the study of new technologies aimed at reducing the engine negative environmental impact and increase its thermal efficiency. One common trend is to develop smaller engines able to operate in stoichiometric conditions across the whole engine map for better efficiency, lower fuel consumption, and optimal conversion rate of the three-way catalyst (TWC). Water injection is one promising technique, as it significantly reduces the engine knock tendency and avoids fuel enrichment for exhaust temperature mitigation at high power operation. With the focus on reducing the carbon footprint of the automotive sector, another vital topic of research is the investigation of new alternative CO2-neutral fuels or so-called eFuels. Several studies have already shown how these new synthetic fuels can be produced by exploiting renewable energy sources and can significantly reduce engine emissions. This work is part of the FVV project number 1367, “Water Injection in Spark-Ignition Engines II”, which investigates the coexistence of two different engine technologies that heads towards the same direction of sustainability of the internal combustion engine: water injection and eFuels. The goal is to assess the advantages that the adoption of an eFuel in combination with water injection strategies can bring, with respect to the same strategies applied in combination with commercial gasoline. Several water injection strategies, including direct water injection, indirect water injection, injection timing, and pressure variations, are considered for a better understanding of the benefits brought by the combination of an eFuel with water injection. For this purpose, experimental tests and 3D-CFD engine simulations have been performed. The physical properties of the investigated eFuel have been experimentally measured for accurate modelling in the simulation environment, and the thermodynamic properties have been evaluated utilizing detailed chemistry calculations. Y1 - 2022 U6 - https://doi.org/10.4271/2022-37-0019 SN - 2688-3627 SN - 0148-7191 ER -