TY - GEN A1 - Morozova, Iuliia A1 - Obrosov, Aleksei A1 - Naumov, Anton A1 - Królicka, Aleksandra A1 - Golubev, Iurii A1 - Bokov, Dmitry O. A1 - Doynov, Nikolay A1 - Weiß, Sabine A1 - Michailov, Vesselin T1 - Impact of Impulses on Microstructural Evolution and Mechanical Performance of Al-Mg-Si Alloy Joined by Impulse Friction Stir Welding T2 - Materials N2 - Impulse Friction Stir Welding (IFSW) was utilized to join 6082–T6 alloy plates at various impulse frequencies. A distinctive feature of IFSW is the generation of mechanical impulses that enhances the forging action of the tool, and thereby, alters the weld microstructure. The microstructural evolution in the Stir Zone (SZ) with special focus on the strengthening precipitation behavior, and overall mechanical properties of the IFSW joints have been investigated. It was demonstrated that the strengthening β″ precipitates reprecipitated in the SZ of the IFSW joints during natural aging. In contrast, no precipitates were found in the SZ of the Friction Stir Welding (FSW) weld. Partial reversion of β″ after IFSW is supposed to occur due to more developed subgrain network and higher dislocation density introduced by impulses that accelerated precipitation kinetics. Dynamic recrystallisation was facilitated by impulses resulting in a fine, homogeneous structure. There was no significant difference between the microhardness in the SZ, tensile and yield strength of the FSW and IFSW joints. However, the application of impulses demonstrated the smoothing of the hardness reduction in the transition region at the advancing side. The shift of the fracture location from the Heat-Affected Zone (HAZ) by FSW to the SZ as well as higher elongation of the joints by IFSW of lower frequencies could be related to the grain refinement and the change of the grain orientation. KW - Al-Mg-Si alloy KW - impulse friction stir welding (IFSW) KW - precipitation KW - microstructure evolution KW - mechanical properties Y1 - 2021 UR - https://www.mdpi.com/1996-1944/14/2/347/htm U6 - https://doi.org/https://doi.org/10.3390/ma14020347 SN - 1996-1944 VL - 14 IS - 2 ER - TY - GEN A1 - Shapovalov, Oleg A1 - Shapovalova, Mariia A1 - Ossenbrink, Ralf A1 - Heckel, Thomas A1 - Michailov, Vesselin A1 - Weiß, Sabine A1 - Gaal, Mate T1 - Verbessern der Korrosionsbeständigkeit eines hochtemperaturbeständigen Ultraschalldämpfungskörpers mittels Laserstrahl-Auftragschweißen T2 - DVS Berichte 2021 N2 - Während in einem konventionellen Ultraschallprüfkopf ein Kunststoffdämpfungskörper mit Kleber oder Öl an einen Piezoschwinger angekoppelt ist, werden als Hochtemperaturlösung feinporöse sintermetallische Dämpfungsmaterialien mit einer Flüssigglasankopplung eingesetzt. Um dabei das Sintermetall vor dem korrosiven Angriff der Glasschmelze zu schützten, wird am Dämpfungskörper gegenwärtig Gold- oder Platinfolie zeit- und kostenaufwendig appliziert. In der aktuellen Arbeit wurde eine Methode zum Korrosionsschutz der sintermetallischen Oberfläche aus rostfreiem Stahl mittels Laser-Pulverauftragschweißen entwickelt. Im Laufe einer Schweißparameterstudie auf dem Substratmaterial aus massivem rostfreiem Stahl wurde die Eignung unterschiedlicher Auftragsmaterialien auf Nickel- und Kobaltbasis untersucht. Dabei wurde zunächst der Einfluss verschiedener Schweißparameter wie Laserleistung, Vorschubgeschwindigkeit und Pulvermenge auf die Auftragsqualität (Nahtform, Vermischungsgrad, Porosität) metallografisch bewertet. Anschließend wurden die aufgetragenen Schichten hinsichtlich ihrer Korrosionsbeständigkeit getestet. Der Kontakt mit einer flüssigen Glasmischung bei 500 °C hat bei keiner der beschichteten Proben sichtbare Korrosionswirkung gezeigt. Als Resultat der Schweißparameterstudie haben sich besonders die nickelbasierten Pulver als gut geeignete Materialien für den Prozess gezeigt. Die identifizierten Schweißparameter wurden im nächsten Schritt erfolgreich an das sintermetallische Substrat angepasst. Y1 - 2021 UR - https://www.dvs-ev.de/call4papers/abstract.cfm?vid=109&pid=7032 SN - 978-3-96144-147-1 SP - 370 EP - 377 PB - DVS Media GmbH CY - Düsseldorf ER - TY - GEN A1 - Ermilova, Evgeniia A1 - Nikitin, Alexander A1 - Weiß, Sabine ED - Daehn, Glenn ED - Cao, Jian ED - Kinsey, Brad ED - Tekkaya, A. Erman ED - Vivek, Anupam ED - Yoshida, Yoshinori T1 - The Local Strain Evolution for Structured Sheet Metals During Uniaxial Deformation T2 - Forming the Future : Proceedings of the 13th International Conference on the Technology of Plasticity N2 - Structured materials can be progressive alternatives to commonly used flat sheets because of their higher bending stiffness and stability compared to flat sheet metals, made of the same alloy. The application of sheet metals requires accurate information regarding their strength and deformation behavior. Such data are not commonly available and have to be measured by specific test setups and implementation of tests. The aim of this work is to obtain new knowledge about deformation mechanisms of structured sheet metals. Structured sheet metals (SSM) made of conventional deep-drawing steel DC04 were investigated by means of tensile tests. The influence of the structure type arrangement on the deformation behavior was analyzed. The evolution of local strains was analyzed by means of strain gauge measurements as well as 3D-displacement measurements with an ARAMIS highresolution camera system. Local orientation changes in different structural elements were measured using the electron backscatter diffraction technique. KW - structured sheet metals, ssm, tensile test, ARAMIS, strain gauge, EBSD, REM, electron microscopy, DC04 steel Y1 - 2021 SN - 978-3-030-75381-8 SN - 978-3-030-75380-1 SN - 978-3-030-75383-2 U6 - https://doi.org/10.1007/978-3-030-75381-8_143 SN - 2367-1696 SP - 1701 EP - 1711 PB - Springer, Cham ET - 1 ER - TY - GEN A1 - Morozova, Iuliia A1 - Kehm, Christian A1 - Obrosov, Aleksei A1 - Yang, Yitong A1 - Miah, Kamal Uddin Mohammad A1 - Uludintceva, Elena A1 - Fritzsche, Sebastian A1 - Weiß, Sabine A1 - Michailov, Vesselin T1 - On the Heat Treatment of Selective-Laser-Melted 316L T2 - Journal of Materials Engineering and Performance N2 - The effect of heat treatment at various temperatures (650, 850, 1050, and 1100°C) and dwell times (10 min and 1 h) on the metallurgical and microstructural evolution as well as on the related tensile properties of stainless steel 316L processed by selective laser melting (SLM) has been systematically evaluated. The metallurgical and microstructural features such as defects, stability of the columnar–cellular structure and substructure, second phase particles, and phase transformation imparted by SLM and heat treatment have been discussed. It has been shown that the processing conditions specific to SLM significantly alter the kinetics of phase evolution compared to standard welding techniques which affects the accuracy of the prediction. The influence of these characteristics on tensile properties and hardness was elucidated. It was disclosed that with increasing heat treatment temperature there was a gradual increase in elongation but a decrease in strength related to the dislocation density and the development of the microstructure. KW - 316L KW - grain structure KW - phase evolution KW - SLM KW - tensile properties Y1 - 2023 U6 - https://doi.org/10.1007/s11665-022-07404-0 SN - 1544-1024 VL - 32 (2023) IS - 10 SP - 4295 EP - 4305 ER - TY - GEN A1 - Morozova, Iuliia A1 - Królicka, Aleksandra A1 - Obrosov, Aleksei A1 - Yang, Yitong A1 - Doynov, Nikolay A1 - Weiß, Sabine A1 - Michailov, Vesselin T1 - Precipitation phenomena in impulse friction stir welded 2024 aluminium alloy T2 - Materials Science and Engineering: A N2 - Microhardness variations across the friction stir welded (FSW) and impulse friction stir welded (IFSW) AA2024–T351 joints have been elucidated by the transformations of the S–Al2CuMg phase with a special focus on a distinguished hardness peak within the heat-affected zone (HAZ) of the impulse welds. The increase in hardness within the stir zone (SZ) originated from the partial re-precipitation of the initial Guinier-Preston-Bagaryatsky zones (GPB) and metastable S needles, previously dissolved.) Formation and growth of stable S precipitates via coalescence accounted for the softening through the thermo-mechanically affected zone (TMAZ). The peak strengthening within the HAZ of the IFSW joints was mainly caused by the dense needle-shaped S particles, which can be explained by a mutual influence of the process specific temperature and strain cycles. Dislocations and subgrain boundaries introduced to the material due to plastic deformation facilitated the nucleation of strengthening S precipitates in the HAZ. It demonstrates that the impact of deformation should be considered by the characterization of the precipitation development in the HAZ. KW - AA2024 KW - impulse friction stir welding KW - microhardness KW - s precipitation KW - thermal cycle KW - deformation Y1 - 2022 U6 - https://doi.org/10.1016/j.msea.2022.143617 SN - 0921-5093 SP - 1 EP - 11 ER - TY - GEN A1 - Evdokimov, Anton A1 - Doynov, Nikolay A1 - Ossenbrink, Ralf A1 - Obrosov, Aleksei A1 - Weiß, Sabine A1 - Michailov, Vesselin T1 - Thermomechanical laser welding simulation of dissimilar steel-aluminum overlap joints T2 - International Journal of Mechanical Sciences N2 - Mixing of steel and aluminum within the weld pool during keyhole laser welding results in a complex dissimilar microstructure, which in turn, initiates a shift in weld metal mechanical properties. In this study, a numerical model for computation of distortions in laser-welded dissimilar overlap joints (austenitic stainless steel 304 – 6082-T6 aluminum alloy), which considers properties of the mixed steel-aluminum weld metal was developed. The required yield strength, Young's modulus, and strain hardening exponent of the weld metal were experimentally determined using the indentation technique coupled with energy-dispersive X-ray spectroscopy. The designed material model calculates the weld elastic-plastic properties as a function of the aluminum concentration. The softening of the alloys in the heat-affected zone was determined by physical simulations and considered as a function of maximum temperature. Computed and measured distortions showed good agreement for various welding regimes with an average deviation of 18.4%. The sensitivity analyses indicated that the application of the developed weld material model significantly improves the accuracy of the thermomechanical simulations. Y1 - 2021 U6 - https://doi.org/10.1016/j.ijmecsci.2020.106019 SN - 1879-2162 VL - 190 ER - TY - GEN A1 - Evdokimov, Anton A1 - Obrosov, Aleksei A1 - Ossenbrink, Ralf A1 - Weiß, Sabine A1 - Michailov, Vesselin T1 - Mechanical properties of dissimilar steel-aluminum weld T2 - Materials Science and Engineering: A N2 - Knowledge of the properties of dissimilar welds is of great significance for the development of multi-material lightweight structures. In this study, stainless steel (1.4301) and aluminum alloy (6082-T6) sheets were welded in overlap configuration in keyhole mode. The resulting weld metals were investigated with respect to their mechanical properties. Several samples were cut out of different locations along the welds and their cross-sections were subjected to indentation testing and energy dispersive X-ray (EDS) analysis. Young's modulus E, yield stress σy, and strain hardening exponent n, were determined by means of reverse analysis of the indentation load (P) – depth (h) curves, allowing construction of true stress – true strain relations. An essential increase in yield stress in comparison to the one of the base alloys was observed inside the weld metal. In contrary, Young's modulus and strain hardening exponent of the welds were almost identical to corresponding values of the base steel metal. Due to the sensitivity of yield stress to the aluminum content, slight variations of the welding parameters lead to significant changes in elastic-plastic behavior of the weld metal. KW - Mechanical properties KW - Indentation KW - Reverse analysis KW - EDS measurements KW - Dissimilar steel aluminum welding KW - FEM Y1 - 2018 UR - https://www.sciencedirect.com/science/article/pii/S0921509318303563 U6 - https://doi.org/https://doi.org/10.1016/j.msea.2018.03.019 SN - 0921-5093 VL - Volume 722 SP - 242 EP - 254 ER - TY - GEN A1 - Kazak, Fedor A1 - Schleuß, Leander A1 - Ossenbrink, Ralf A1 - Michailov, Vesselin A1 - Weiß, Sabine T1 - Particularities of testing structured sheet metals in 3-point bending tests T2 - Materials Testing N2 - Thin sheet metals from deep drawing steel DC04 are very often used in the production of car body and case parts. Quality improvement of sheet metal components by new constructive solutions (structuring) as well as adapted joining technology is going on. Structured sheet metals differ from each other by their high bending stiffness. At the same time, they show certain anisotropy due to the structure. Therefore a typical testing method of structured semi-finished parts (single sheet metals, sandwiches)is the bending test. The literature review revealed that in many studies no special demands on tests of structured materials were made. This concerns particularly the structure arrangement, structure direction and structure location of the specimen relative to the mandrel position during bending tests, i. e., the direction of the fixed load relative to the structure. The aim of this study was to determine the influence of the test specification on flexural behavior. In the present paper, honeycomb-structured sheet metals were examined using 3-point bending tests. Bending stiffness and lightweight potential were calculated with respect to the location of load application and compared for different structure arrangements,directions and locations. The influence of the anisotropy on flexural behavior of the honeycomb-patterned sheet metals was moderate. Y1 - 2016 U6 - https://doi.org/10.3139/120.110883 SN - 0025-5300 SN - 2195-8572 VL - 58 IS - 6 SP - 495 EP - 500 ER -