@misc{DongAulGregoireetal., author = {Dong, Shijun and Aul, Christopher and Gregoire, Claire and Cooper, Sean P. and Mathieu, Olivier and Petersen, Eric L. and Rodriguez, Jose and Mauß, Fabian and Wagnon, Scott W. and Kukkadapu, Goutham and Pitz, William J. and Curran, Henry J.}, title = {A comprehensive experimental and kinetic modeling study of 1-hexene}, series = {Combustion and Flame}, volume = {232}, journal = {Combustion and Flame}, issn = {1556-2921}, doi = {10.1016/j.combustflame.2021.111516}, abstract = {It is important to understand the low-temperature chemistry of 1-hexene as it is used as a representative alkene component in gasoline surrogate fuels. Ignition delay times (IDTs) of 1-hexene measured in rapid compression machines (RCMs) can be used to validate its low-temperature chemistry. However, volume history profiles are not available for published RCM IDT data. This has restricted the validation of the low-temperature chemistry of 1-hexene at engine-relevant conditions (i.e. at low temperatures and high pressures). Thus, new RCM IDT data with associated volume history profiles are needed. In this study, both an RCM and a high-pressure shock tube (ST) are employed to measure IDTs of 1-hexene at equivalence ratios of 0.5, 1.0 and 2.0 in 'air' and at pressures of 15 and 30 atm. A cool-flame (first stage) and total (second stage) ignition was observed in the RCM experiments. Moreover, carbon monoxide and water versus time histories produced during 1-hexene oxidation at highly diluted conditions were measured in a ST. A new detailed chemical kinetic model describing 1-hexene oxidation is proposed and validated using these new measured data together with various experimental data available in the literature. The kinetic model can predict well the auto-ignition behavior and oxidation processes of 1-hexene at various conditions. The rate constants and branching ratio for hydroxyl radical addition to the double bond of 1-hexene are particularly important and discussed based on the experimental and theoretically calculated results from previous studies as well as validation results from jet-stirred reactor (JSR) species profiles. Flux and sensitivity analyses are performed to determine the important reaction classes for 1-hexene oxidation and show that the reactions associated with hydroxy radical addition to the double bond contribute most to the low-temperature reactivity of 1-hexene. In the negative temperature coefficient (NTC) regime, the isomerization of hexenyl-peroxy radicals promotes fuel reactivity due to its associated chain branching pathways.}, language = {en} } @misc{MatriscianoFrankenGonzalezMestreetal., author = {Matrisciano, Andrea and Franken, Tim and Gonzalez Mestre, Laura Catalina and Borg, Anders and Mauß, Fabian}, title = {Development of a Computationally Efficient Tabulated Chemistry Solver for Internal Combustion Engine Optimization Using Stochastic Reactor Models}, series = {Applied Sciences}, volume = {10}, journal = {Applied Sciences}, number = {24}, issn = {2076-3417}, doi = {10.3390/app10248979}, abstract = {The use of chemical kinetic mechanisms in computer aided engineering tools for internal combustion engine simulations is of high importance for studying and predicting pollutant formation of conventional and alternative fuels. However, usage of complex reaction schemes is accompanied by high computational cost in 0-D, 1-D and 3-D computational fluid dynamics frameworks. The present work aims to address this challenge and allow broader deployment of detailed chemistry-based simulations, such as in multi-objective engine optimization campaigns. A fast-running tabulated chemistry solver coupled to a 0-D probability density function-based approach for the modelling of compression and spark ignition engine combustion is proposed. A stochastic reactor engine model has been extended with a progress variable-based framework, allowing the use of pre-calculated auto-ignition tables instead of solving the chemical reactions on-the-fly. As a first validation step, the tabulated chemistry-based solver is assessed against the online chemistry solver under constant pressure reactor conditions. Secondly, performance and accuracy targets of the progress variable-based solver are verified using stochastic reactor models under compression and spark ignition engine conditions. Detailed multicomponent mechanisms comprising up to 475 species are employed in both the tabulated and online chemistry simulation campaigns. The proposed progress variable-based solver proved to be in good agreement with the detailed online chemistry one in terms of combustion performance as well as engine-out emission predictions (CO, CO2, NO and unburned hydrocarbons). Concerning computational performances, the newly proposed solver delivers remarkable speed-ups (up to four orders of magnitude) when compared to the online chemistry simulations. In turn, the new solver allows the stochastic reactor model to be computationally competitive with much lower order modeling approaches (i.e., Vibe-based models). It also makes the stochastic reactor model a feasible computer aided engineering framework of choice for multi-objective engine optimization campaigns.}, language = {en} } @misc{FrankenSeidelGonzalezMestreetal., author = {Franken, Tim and Seidel, Lars and Gonzalez Mestre, Laura Catalina and Shrestha, Krishna Prasad and Matrisciano, Andrea and Mauss, Fabian}, title = {Assessment of Auto-Ignition Tendency of Gasoline, Methanol, Toluene and Hydrogen Fuel Blends in Spark Ignition Engines}, series = {THIESEL 2020 Conference on Thermo-and Fluid Dynamic Processes in Direct Injection Engines}, journal = {THIESEL 2020 Conference on Thermo-and Fluid Dynamic Processes in Direct Injection Engines}, pages = {23}, abstract = {State of the art spark ignited gasoline engines achieve thermal efficiencies above 46 \% e.g. due to friction optimized crank trains, high in-cylinder tumble flow and direct fuel injection. Further improvements of thermal efficiency are expected from lean combustion, higher compression ratio and new knock-resistant fuel blends. One of the limitations to these improvements are set by the autoignition in the end gas, which can develop to knocking combustion and severely damage the internal combustion engine. The auto-ignition is enhanced by high cylinder gas temperatures and reactive species in the end gas composition. Quasi-dimensional Stochastic Reactor Model simulations with detailed chemistry allow to consider the thermochemistry properties of surrogates and complex end gas compositions. Based on the detailed reaction scheme and surrogate model, an innovative tabulated chemistry approach is utilized to generate dual-fuel laminar flame speed and combustion chemistry look-up tables. This reduces the simulation duration to seconds per cycle, while the loss in accuracy compared to solving the chemistry "online" is marginal. The auto-ignition events predicted by the tabulated chemistry simulation are evaluated using the Detonation Diagram developed by Bradley and co-workers. This advanced methodology for quasi-dimensional models evaluates the resonance between the shock wave and reactionfront velocity from auto-ignition in the end gas and determines if it is a harmful developing detonation or normal deflagration. The aim of this work is to evaluate the auto-ignition characteristics of different fuel blends. The Stochastic Reactor Model with tabulated chemistry is applied to perform a numerical analysis of the autoignition of the fuel blends and operating conditions. Experimental measurements of a single cylinder research engine operated with RON95 E10 fuel are used to train and validate the simulation model. The RON95 E10 fuel is blended with Methanol, Hydrogen and Toluene. The knock tendency based on the evaluation of auto-ignition events of the different fuel blends are analysed for three operating points at 1500 rpm 15 bar IMEP, 2000 rpm 20 bar IMEP and 2500 rpm 15 bar IMEP with advanced spark timings.}, language = {en} } @misc{MatriscianoNetzerWerneretal., author = {Matrisciano, Andrea and Netzer, Corinna and Werner, Adina and Borg, Anders and Seidel, Lars and Mauß, Fabian}, title = {A Computationally Efficient Progress Variable Approach for In-Cylinder Combustion and Emissions Simulations}, series = {SAE Technical Paper}, journal = {SAE Technical Paper}, issn = {0148-7191}, doi = {10.4271/2019-24-0011}, abstract = {The use of complex reaction schemes is accompanied by high computational cost in 3D CFD simulations but is particularly important to predict pollutant emissions in internal combustion engine simulations. One solution to tackle this problem is to solve the chemistry prior the CFD run and store the chemistry information in look-up tables. The approach presented combines pre-tabulated progress variable-based source terms for auto-ignition as well as soot and NOx source terms for emission predictions. The method is coupled to the 3D CFD code CONVERGE v2.4 via user-coding and tested over various speed and load passenger-car Diesel engine conditions. This work includes the comparison between the combustion progress variable (CPV) model and the online chemistry solver in CONVERGE 2.4. Both models are compared by means of combustion and emission parameters. A detailed n-decane/α-methyl-naphthalene mechanism, comprising 189 species, is used for both online and tabulated chemistry simulations. The two chemistry solvers show very good agreement between each other and equally predict trends derived experimentally by means of engine performance parameters as well as soot and NOx engine-out emissions. The CPV model shows a factor 8 speed-up in run-time compared to the online chemistry solver without compromising the accuracy of the solution.}, language = {en} } @misc{FrankenDugganMatriscianoetal., author = {Franken, Tim and Duggan, Alexander and Matrisciano, Andrea and Lehtiniemi, Harry and Borg, Anders and Mauß, Fabian}, title = {Multi-Objective Optimization of Fuel Consumption and NO x Emissions with Reliability Analysis Using a Stochastic Reactor Model}, series = {SAE Technical Paper}, journal = {SAE Technical Paper}, issn = {0148-7191}, doi = {10.4271/2019-01-1173}, abstract = {The introduction of a physics-based zero-dimensional stochastic reactor model combined with tabulated chemistry enables the simulation-supported development of future compression-ignited engines. The stochastic reactor model mimics mixture and temperature inhomogeneities induced by turbulence, direct injection and heat transfer. Thus, it is possible to improve the prediction of NOx emissions compared to common mean-value models. To reduce the number of designs to be evaluated during the simulation-based multi-objective optimization, genetic algorithms are proven to be an effective tool. Based on an initial set of designs, the algorithm aims to evolve the designs to find the best parameters for the given constraints and objectives. The extension by response surface models improves the prediction of the best possible Pareto Front, while the time of optimization is kept low. This work presents a novel methodology to couple the stochastic reactor model and the Non-dominated Sorting Genetic Algorithm. First, the stochastic reactor model is calibrated for 10 low, medium and high load operating points at various engine speeds. Second, each operating point is optimized to find the lowest fuel consumption and specific NOx emissions. The optimization input parameters are the temperature at intake valve closure, the compression ratio, the start of injection, the injection pressure and exhaust gas recirculation rate. Additionally, it is ensured that the maximum peak cylinder pressure and turbine inlet temperature are not exceeded. This enables a safe operation of the engine and exhaust aftertreatment system under the optimized conditions. Subsequently, a reliability analysis is performed to estimate the effect of off-nominal conditions on the objectives and constraints. The novel multi-objective optimization methodology has proven to deliver reasonable results. The zero-dimensional stochastic reactor model with tabulated chemistry is a fast running physics-based model that allow to run large optimization problems in a short amount of time. The combination with the reliability analysis also strengthens the confidence in the simulation-based optimized engine operation parameters.}, language = {en} } @misc{KurapatiBorgSeideletal., author = {Kurapati, Vinaykumar Reddy and Borg, Anders and Seidel, Lars and Mauß, Fabian}, title = {Fast CFD Diesel engine modelling using the 1-Dimentional SprayLet approach}, series = {SAE Technical Paper}, journal = {SAE Technical Paper}, number = {2024-01-2684}, issn = {0148-7191}, abstract = {In the SAE article 2023-24-0083: SprayLet: One-dimensional interactive cross-sectionally averaged spray model, we formulatet a one-dimensional Spray model in interaction with the surrounding gas phase. We could demonstrate, that the model predicted liquid and gaseous penetration length in good aggreement with ECN spray experiments. In this paper we use this model in engine CFD (CONVERGE CFD) and demonstrate a strong reduction in CPU time (50\%). We can show a strong decrease in grid dependency, which allows a further reduction of CPU time (90\%). We will present engine CFD simulations, comparing detailed spray with SpayLet simulations. This includes pressure traces, heat release, and emissions.}, language = {en} } @misc{KurapatiBorgSeideletal., author = {Kurapati, Vinaykumar Reddy and Borg, Anders and Seidel, Lars and Mauß, Fabian}, title = {SprayLet: One-Dimensional Interactive Cross-Sectionally Averaged Spray Model}, series = {SAE Technical Paper}, journal = {SAE Technical Paper}, issn = {0148-7191}, doi = {10.4271/2023-24-0083}, abstract = {Spray modeling is among the main aspects of mixture formation and combustion in internal combustion engines. It plays a major role in pollutant formation and energy efficiency although adequate modeling is still under development. Strong grid dependence is observed in the droplet-based stochastic spray model commonly used. As an alternative, an interactive model called 'SprayLet' is being developed for spray simulations based on one-dimensional integrated equations for the gas and liquid phases, resulting from cross-sectionally averaging of multi-dimensional transport equations to improve statistical convergence. The formulated one-dimensional cross-section averaged system is solved independently of the CFD program to provide source terms for mass, momentum and heat transfer between the gas and liquid phases. The transport processes take place in a given spray cone where the nozzle exit is automatically resolved. In the 1D program, the conservation equations are for droplet diameter, droplet temperature, as well as for continuity and momentum of the liquid and the gaseous phase are solved. The source terms between the phases are conservatively embedded into the spray region of the CFD program. In CFD program, the transport equations are solved for gas phase only. The SprayLet model is validated using standard Sandia sprays by comparing penetration lengths and fuel mixture fractions with experimental data.}, language = {en} } @misc{MannaSabiaShresthaetal., author = {Manna, Maria Virginia and Sabia, Pino and Shrestha, Krishna Prasad and Seidel, Lars and Ragucci, Raffaele and Mauß, Fabian and De Joannon, Mara}, title = {NH3NO interaction at low-temperatures: an experimental and modeling study}, series = {Proceedings of the Combustion Institute}, volume = {39}, journal = {Proceedings of the Combustion Institute}, number = {1}, issn = {1873-2704}, doi = {10.1016/j.proci.2022.09.027}, pages = {775 -- 784}, abstract = {The present work provides new insight into NH3single bondNO interaction under low-temperature conditions. The oxidation process of neat NH3 and NH3 doped with NO (450, 800 ppm) was experimentally investigated in a Jet Stirred Flow Reactor at atmospheric pressure for the temperature range 900-1350 K. Results showed NO concentration is entirely controlled by DeNOx reactions in the temperature range 1100-1250 K, while NH3single bondNO interaction does not develop through a sensitizing NO effect, for these operating conditions. A detailed kinetic model was developed by systematically updating rate constants of controlling reactions and declaring new reactions for N2H2 isomers (cis and trans). The proposed mechanism well captures target species as NO and H2 profiles. For NH3single bondNO mixtures, NO profiles were properly reproduced through updated DeNOx chemistry, while NH2 recombination reactions were found to be essential for predicting the formation of H2. The role of ammonia as a third-body species is implemented in the updated mechanism, with remarkable effects on species predictions. For neat NH3 mixture, the reaction H+O2(+M)=HO2(+M) was crucial to predict NO formation via the reaction NH2+HO2double bondH2NO+OH.}, language = {en} } @misc{MantePrehnTheileetal., author = {Mante, Till and Prehn, Sascha and Theile, Martin and Seidel, Lars and Mestre, Laura and Buchholz, Bert and Mauß, Fabian}, title = {Investigation of An Ammonia Diesel Dual-Fuel Combustion Process on a Heavy-Duty Single Cylinder Research Engine for the Development of Suitable Simulation Tools for Maritime Applications}, series = {Heavy-Duty-, On- und Off-Highway-Motoren 2022 : Stand der Energiewende im Heavy-Duty-Bereich}, journal = {Heavy-Duty-, On- und Off-Highway-Motoren 2022 : Stand der Energiewende im Heavy-Duty-Bereich}, editor = {Heintzel, Alexander}, publisher = {Springer Vieweg}, address = {Wiesbaden}, isbn = {978-3-658-41477-1}, doi = {10.1007/978-3-658-41477-1_3}, pages = {24 -- 39}, abstract = {This paper discusses the adaption of a single cylinder research engine for a retrofit application with an ammonia diesel dual-fuel combustion process and the build of an ammonia fuel system. The gaseous ammonia will be injected in the air intake pipe and the premixed ammonia air mixture will enter the combustion chamber. The diesel injection is carried out via a high-pressure common rail system. All relevant parameters can be freely adjusted via a freely programmable control unit. With the help of experimental data from a single cylinder research engine at the chair of piston machines and internal combustion engines of the University of Rostock (LKV), a dual-fuel combustion model based on detailed chemistry will be developed and optimized. This model will be integrated in a full research engine model, which ensures the best possible representation of the real engine. The combustion model is being developed by LOGE Deutschland GmbH. The full research engine model is developed by FVTR GmbH. The analysis of the combustion process starts with pure diesel operating points and is successively substituted by ammonia in the course of the measurement campaigns. Both the combustion characteristics are relevant, as they significantly influence the resulting performance and engine operation, as well as the exhaust emissions, as the carbon emissions can be reduced, but the nitrogen oxides and ammonia slip increase significantly in relevance due to the ammonia. The results obtained will be used to derive initial recommendations for action and to estimate the potential for application in the inland waterway shipping. In addition, the development of the systematic simulation tools covers a broad spectrum of research questions and aims to increase the efficiency of the necessary R\&D.}, language = {en} } @misc{Turquandd'AuzayShapiroProuvieretal., author = {Turquand d'Auzay, Charles and Shapiro, Evgeniy and Prouvier, Matthieu and Winkler, Axel and Seidel, Lars and Borg, Anders and Mauß, Fabian}, title = {Evaluation of Fast Detailed Kinetics Calibration Methodology for 3D CFD Simulations of Spray Combustion}, series = {SAE Technical Paper}, journal = {SAE Technical Paper}, number = {2022-01-1042}, issn = {0148-7191}, doi = {10.4271/2022-01-1042}, abstract = {Meeting strict current and future emissions legislation necessitates development of computational tools capable of predicting the behaviour of combustion and emissions with an accuracy sufficient to make correct design decisions while keeping computational cost of the simulations amenable for large-scale design space exploration. While detailed kinetics modelling is increasingly seen as a necessity for accurate simulations, the computational cost can be often prohibitive, prompting interest in simplified approaches allowing fast simulation of reduced mechanisms at coarse grid resolutions appropriate for internal combustion engine simulations in design context. In this study we present a simplified Well-stirred Reactor (WSR) implementation coupled with 3D CFD Ricardo VECTIS solver. A detailed evaluation of benchmark ECN spray problem is presented demonstrating that a single point calibration of such a model using a bulk reaction multiplier approach can provide correct representation of the solution across a wide range of temperatures on grid sizes typically employed for RANS internal combustion engine simulations with tabulated kinetics or zonal combustion models.}, language = {en} } @misc{VanTreekLubranoLavaderaSeideletal., author = {Van Treek, Lisa and Lubrano Lavadera, Marco and Seidel, Lars and Mauß, Fabian and Konnov, Alexander A.}, title = {Experimental and modelling study of laminar burning velocity of aqueous ethanol}, series = {Fuel}, volume = {257}, journal = {Fuel}, issn = {1873-7153}, doi = {10.1016/j.fuel.2019.116069}, abstract = {Laminar burning velocities of ethanol-water-air mixtures have been determined using the heat flux method. Aqueous ethanol contained 0-40\% of water by mole fraction. Laminar premixed flat flames were stabilized on a perforated burner under adiabatic conditions for the equivalence ratio range from 0.7 to 1.4. Burning velocity measurements were performed for the initial gas temperature of 358 K and at atmospheric pressure. The results for ethanol-air flames are in good agreement with the previous data obtained using the same heat flux method. The present and literature experimental data were compared against predictions using four different kinetic models. All models show uniform behaviour over the range of ethanol dilution by water covered in the present study. However, model predictions significantly diverge from the experimental data obtained in spherical flames. To quantify the effect of dilution on the laminar burning velocity, an empirical dimensionless correlation has been derived from the experimental data and predictions of the models tested. Further numerical analyses were performed to identify the effects of water addition on laminar burning velocities. Results suggested that water strongly interacts with the H2/O2 and C1 oxidation/recombination routes.}, language = {en} }