@inproceedings{SimonEngelRussig, author = {Simon, Sylvio and Engel, Sebastian and Russig, Martin}, title = {Fertigung lamellierter Werkzeuge mittels Wasserstrahlschneiden}, series = {Tagungsband, 12. Wissenschaftstage der Hochschule Lausitz, 28. - 30. November 2012}, booktitle = {Tagungsband, 12. Wissenschaftstage der Hochschule Lausitz, 28. - 30. November 2012}, publisher = {Hochschule Lausitz}, address = {Senftenberg}, isbn = {3-9810211-5-0}, pages = {3}, language = {de} } @inproceedings{Simon, author = {Simon, Sylvio}, title = {RFID basierte Produktkennzeichnung und m{\"o}gliche Verbesserungen im Instandhaltungsprozess in der Montanindustrie}, series = {Tagungsband, 12. Wissenschaftstage der Hochschule Lausitz, 28. - 30. November 2012}, booktitle = {Tagungsband, 12. Wissenschaftstage der Hochschule Lausitz, 28. - 30. November 2012}, publisher = {Hochschule Lausitz}, address = {Senftenberg}, isbn = {3-9810211-5-0}, pages = {3}, language = {de} } @misc{AmirovShiraliyev, author = {Amirov, Fariz and Shiraliyev, Ilgar}, title = {Research on wear and tear of the mud pump liners}, series = {Conference Proceedings of the 4th International Conference on Energy Supply and Energy Efficiency and "5 Years NESEFF", 28 Sep - 04 Okt 2020}, journal = {Conference Proceedings of the 4th International Conference on Energy Supply and Energy Efficiency and "5 Years NESEFF", 28 Sep - 04 Okt 2020}, editor = {Simon, Sylvio}, address = {Cottbus}, isbn = {978-3-940471-59-8}, pages = {65 -- 66}, abstract = {The article tells about the research on wear and tear of mud pump liners, namely: main characteristics that distinguish ceramic liner from the other ones used on the units equipped with the hydraulic system for washing out the drilling wells from cuttings, design of ceramic liners, calculation of the wear rate of ceramic liners, and the positive contribution they made on the modern drilling process. Besides, the research is made on the simplicity of the structure of ceramic liners, a short amount of time consumed to assemble and replace the liners, safety of the work, cost-effectiveness, wearing and corrosion durability, and also compliance with other requirements.}, language = {en} } @misc{SimonFraňaNeubertetal., author = {Simon, Sylvio and Fraňa, Karel and Neubert, Christian and Mammadov, Arastun and Amirov, Fariz}, title = {A Flow Study in the Cyclone with Particle Separations}, series = {Computational and Experimental Simulations in Engineering, Proceedings of ICCES 2020. Volume 1}, volume = {Mechanisms and Machine Science}, journal = {Computational and Experimental Simulations in Engineering, Proceedings of ICCES 2020. Volume 1}, editor = {Atluri, Satya N. and Vušanović, Igor}, edition = {1. Auflage}, publisher = {Springer}, address = {Cham}, isbn = {978-3-030-64689-9}, issn = {2211-0984}, doi = {10.1007/978-3-030-64690-5_6}, pages = {52 -- 59}, abstract = {Unsteady turbulent flows with solid particles of different sizes in the cyclone were studied numerically and experimentally. The grid studies and influence of the boundary condition prescription on the flow behavior in the cyclone and the effectiveness of the particle separation were studied firstly numerically. The turbulent flow was calculated by means of Large Eddy Simulations and this flow problem was calculated parallel using eight processors. It was found theoretically that pressure at the bottom outlet of the cyclone has a significant impact on the particle separation. This impact of the pressure at the cyclone function was examined also using experiments and pressure distributions for different flow rate intensities for several locations in the cyclone were determined. These experimental results can be used for a validation of numerical results. Furthermore, the larger losses were observed in the immersion tube due to higher flow velocity and impulse exchange in the vortex core.}, language = {en} } @misc{AmirovShiraliyev, author = {Amirov, Fariz and Shiraliyev, Ilgar}, title = {Reducing maintenance costs by increasing the service life of mud pump ceramic liners}, series = {Oil Gas European Magazine · August 2022, DVV Media Group GmbH, Deutschland}, journal = {Oil Gas European Magazine · August 2022, DVV Media Group GmbH, Deutschland}, number = {2}, issn = {0179-3187}, doi = {10.19225/220204}, pages = {32 -- 34}, abstract = {The article tells about the research on wear and tear of mud pump liners, namely: main characteristics that distinguish ceramic liners from others used on the units equipped with a hydraulic system for washing out the drilling wells from cuttings, design of ceramic liners, calculation of the wear rate of ceramic liners, and the positive contribution they have made on the modern drilling process. Besides, the research is made on the simplicity of the structure of ceramic liners, little time required to assemble and replace the liners, safety of the work, cost-effectiveness, wearing and corrosion durability, and also compliance with other requirements.}, language = {en} } @misc{AmirliFritzscheAbbasovetal., author = {Amirli, Samir and Fritzsche, Pascal and Abbasov, Ilgar and Wichmann, Steffen and Simon, Sylvio and Amirov, Fariz and Mammadov, Arastun}, title = {The İmpact of High Speed Mechanical Processing Efficiency on the Production Process}, series = {HERALD of the Azerbaijan Engineering Academy}, volume = {14}, journal = {HERALD of the Azerbaijan Engineering Academy}, number = {1}, issn = {2076-0515}, doi = {10.52171/2076-0515_2022_14_01_41_51}, pages = {41 -- 51}, abstract = {The main purpose of the article is to increase productivitiy, reduce processing time and the same time increase the cutting speed. The results are also displayed in Excel using a number of cutting parameters. For this purpose, the article shows the results of both high-speed milling and high-speed turning of a machine with different types of tools, as well as processing of one tool on different types of machines. Unlike other machines, in general, the work on the machines of universal processing centers turned out to be more productive. The feed rate of the machine tools is the focus area here. If we increase cutting values, then the tool life is reduced and that leads to higher tool costs. With universal high-performance machines we cannot save costs for tools (we can only save machine tool costs). Compared to universal high-performance machines, we can save tool costs with Universal Machining Center. Therefore, it is suggested to the machining with the universal machining center, although the machining time and cutting time is faster with the universal high-performance machine.}, language = {en} } @misc{AmirovSimonWichmannetal., author = {Amirov, Fariz and Simon, Sylvio and Wichmann, Steffen and Amirli, Samir and Fraňa, Karel}, title = {Determining the Accuracy of Water Pressure Processing using 3D Scanning}, series = {HERALD of the Azerbaijan Engineering Academy}, volume = {13}, journal = {HERALD of the Azerbaijan Engineering Academy}, number = {3}, issn = {2076-0515}, pages = {38 -- 44}, abstract = {The article provides the results of the study of manufacturing tolerances in waterjet cutting by the method of three-dimensional (3D) measurements: shape deviations were shown by three-dimensional comparison of scanned samples. The dimensions were also measured using two-dimensional (2D) sections of the scanned samples. It has been determined that the clean waterjet cutting tends to separate soft materials such as plastic, foil, foam or paper, as well as food. Unlike the pure waterjet cutting, the abrasive cutting is used for hard materials such as steel, ceramics, glass. The optimal pressure for material processing has been calculated. Particular emphasis is placed on the separation of composite materials, which cannot be satisfactorily accomplished using conventional methods.}, language = {ru} } @misc{RasimAmirov, author = {Rasim, Bashirov and Amirov, Fariz}, title = {Выбор материала и геометрических параметров расточного резца для обработки покрытий на основе никеля}, series = {ИЗВЕСТИЯ ВЫСШИХ УЧЕБНЫХ ЗАВЕДЕНИЙ. МАШИНОСТРОЕНИЕ}, volume = {8(761)}, journal = {ИЗВЕСТИЯ ВЫСШИХ УЧЕБНЫХ ЗАВЕДЕНИЙ. МАШИНОСТРОЕНИЕ}, number = {8}, issn = {0536-1044}, doi = {10.18698/0536-1044-2023-8-78-86}, pages = {78 -- 86}, abstract = {Разработка технологии механической обработки восстанавливаемых в ремонтном производстве деталей, включающая в себя выбор способа и режимов их обработки, режущего инструмента и др., является сложной задачей, решение которой определяет качество восстанавливаемых изделий. Качество механической обработки во многом зависит от обрабатываемости металла, под которой понимают способность материала подвергаться резанию. Рассмотрены особенности механической обработки втулок по- сле восстановления изношенной внутренней поверхности, состоящей из черного, чи- стового и тонкого растачивания, а также операции хонингования. При механической обработке восстанавливаемых втулок наибольшую трудность представляют операции чернового и чистового растачивания, так как после индукционного напекания с по- следующим раскатыванием твердость получаемых слоев находится в пределах HRC 48…55, что усложняет работу резцов при растачивании втулок. Для наплавки на де- тали, работающие в условиях изнашивания (коррозионного, эрозионного и термиче- ского), применяют порошок ПГ-СР2, имеющий систему легирования Ni-Cr-B-Si. Значительную волнистость и шероховатость поверхности, возникающую в результате наплавки, устраняют накатыванием. Одним из важных вопросов при обработке по- крытий, нанесенных центробежным индукционным напеканием с последующим рас- катыванием, является выбор материала и геометрических параметров режущего ин- струмента для чернового и чистового растачивания. При правильном выборе матери- ала и геометрических параметров расточного резца можно значительно уменьшить износ режущего инструмента, что позволит увеличить его стойкость и производи- тельность обработки, а следовательно, снизить себестоимость изготовления детали. Исследовано влияние технологических параметров на износ и геометрических пара- метров на стойкость режущего инструмента с целью оптимизации условий растачи- вания восстановленных цилиндров судовых двигателей.}, language = {ru} } @misc{BashirovAmirov, author = {Bashirov, Rasim and Amirov, Fariz}, title = {Методика определения теплового состояния втулки цилиндра при центрoбежном индукционном напекании}, series = {ИЗВЕСТИЯ ВЫСШИХ УЧЕБНЫХ ЗАВЕДЕНИЙ. МАШИНОСТРОЕНИЕ}, volume = {8(749)}, journal = {ИЗВЕСТИЯ ВЫСШИХ УЧЕБНЫХ ЗАВЕДЕНИЙ. МАШИНОСТРОЕНИЕ}, number = {8}, issn = {0536-1044}, doi = {10.18698/0536-1044-2022-8-33-41}, pages = {33 -- 41}, abstract = {Распределение температуры во втулке цилиндра судового двигателя при ее нагреве и охлаждении — один из важнейших факторов, под действием которых формируются структура и свойства покрытий в процессе восстановления цилиндра методом центро- бежного индукционного напекания. Проведены экспериментальные исследования, позволившие получить графики распределения температуры по диаметрам втулки ци- линдра судового двигателя при ее нагреве и охлаждении. Установлено, что на процесс напекания порошковых материалов существенно влияют теплофизические свойства втулки. Изменяя скорость нагрева, можно получать покрытия при различных значени- ях температуры и времени напекания. Выполнено моделирование распределения тем- пературы в стенке втулки цилиндра при центробежном индукционном напекании в за- висимости от времени напекания, а также с учетом геометрических параметров втулки, теплоотдачи, теплопроводности, материала втулки, температуры внешней среды и т. д. Получены выражения для определения распределения температуры в стенке втулки цилиндра при центробежном индукционном напекании. Задавая значения параметров центробежного индукционного напекания, по полученным формулам можно смодели- ровать и заранее получить распределение температуры в стенке втулки цилиндра. Для визуального отображения изменения температурного поля во втулке при центробеж- ном индукционном напекании выполнено моделирование в среде Autodesk Fusion 360.}, language = {ru} } @misc{SeidlitzSimonElzeetal., author = {Seidlitz, Holger and Simon, Sylvio and Elze, Lars and Schulze, Marcus}, title = {Herstellung von strukturierten Leichtbaukomponenten}, language = {de} }