@misc{FranzKuehhornGierschetal., author = {Franz, Falco and K{\"u}hhorn, Arnold and Giersch, Thomas and Schrape, Sven and Figaschewsky, Felix}, title = {Influence of Inlet Distortions on the Forced Vibration of a High Pressure Compressor Rig}, series = {ASME 2020 Turbo Expo - Virtual Conference, September 2020}, journal = {ASME 2020 Turbo Expo - Virtual Conference, September 2020}, abstract = {The accurate prediction of blade vibrations is a key factor for the development of reliable turbomachines. This paper focusses on forced vibrations. The excitation frequency is an integer multiple of the rotor revolution frequency, which is commonly called engine order. Aerodynamic excitation of blades is created by stator wakes or the potential fields of downstream obstacles, which usually leads to high engine orders correlating to the number of vanes. Resonance crossings appear at higher frequencies corresponding to higher modes. Besides high engine orders, low engine orders not related to the number of vanes may exist. They can be caused by a disturbance of the perfect cyclic symmetry of the flow pattern due to geometry variations or inlet distortions. Inlet distortions result from installation effects, maneuvers or crosswind. Low engine orders affect fundamental modes at high engine speeds. High static loads due to centrifugal forces combined with dynamic excitation and low damping may lead to unacceptable high stresses. This paper aims at getting a better understanding of the simulative prediction of low engine order excitation with special focus on inlet distortions. Under investigation is a 4.5 stage research compressor rig, for which an extensive amount of test data is available. A three dimensional CFD-model of the compressor is used to compute the forcings generated by different distortion patterns. The first two stages are modeled as a full-annulus, which allows to fully resolve the spatial content of the inlet distortion patterns. The rotor 2 blisk is of special interest in this investigation. The propagation of the distortion after stage 2 with rotor 2 is not of interest, therefore the downstream stages are modeled as single passages in order to save computational time. The distortion patterns are the outcome of traversals of different screens with total pressure probes. During distortion measurements, the screens located in the inlet duct were rotated relative to the fixed instrumentation. The traversals in resonance of the first bending mode of rotor 2 with a low engine order four showed a dependency of the screen angle on the vibration amplitude. Acceleration and deceleration maneuvers through this resonance were conducted with screen angles set to those of smallest and highest response. Vibration amplitudes of the blisk rotor are measured by strain gauges and a blade tip timing system. Simulation results are compared against vibration measurements. Aerodynamic damping is calculated with the influence coefficient method. The effects of mistuning are included in the calculation of vibration amplitudes via a subset of nominal system modes model to give a meaningful comparison against real engine hardware. The mistuning distribution of the blisk was identified at rest for the fundamental bending mode. The presence of a 2nd excitation mechanism of unknown source explains the observed test data. This unknown source is not included in the CFD model. A direct comparison of simulation and measurement is still possible by leveraging the observed superposition effects of both excitation sources. The consequent approach is to identify and substract the forcing due to the unknown source, leaving only the delta forcing due to inlet distortions.}, language = {en} } @misc{GambittaKuehhornSchrape, author = {Gambitta, Marco and K{\"u}hhorn, Arnold and Schrape, Sven}, title = {Geometrical Variability Modelling of Axial Compressor Blisk Aerofoils and Evaluation of Impact on the Forced Response Problem}, series = {ASME 2020 Turbo Expo - Virtual Conference, September 2020}, journal = {ASME 2020 Turbo Expo - Virtual Conference, September 2020}, abstract = {The manufacturing process always produces onto the components a certain amount of geometrical uncertainty. This results inevitably in the introduction of a certain amount of variability within the manufactured parts. Even if the differences are small, all the resulting geometries will differ from each other. The present work focuses on the effect of the manufacturing geometrical variability on the high pressure compressor of a turbofan engine for civil aviation. The deviations of the geometry over the axial compressor blades are studied and modelled for the representation in the computational models. Such variability is of particular interest for the forced response problem, where small deviations of the geometry from the ideal nominal model can imply significant differences in the vibrational responses. The information regarding the geometrical mistuning is extracted from a set of manufactured components surface scans of a blade integrated disk (blisk) rotor. The measured geometries are analyzed over a large amount of set radial sections, defining a set of opportune parameters to represent the deviations from the nominal design. A spline fit of the parameters over the radial sections allows the creation of a set of variables describing the geometry. The dimension of the variables domain is reduced using the principal component analysis approach, this allows to obtain an optimal subset of geometrical modes as linear combination of the above mentioned parameters. The reconstruction of the modelled geometries is performed for the implementation in complex CFD and FEM solvers. This is done via the application of the modelled delta nominal-to-measure geometrical offset to the hot geometry of the desired test case. The generated model allows a stochastic representation of the variability, providing an optimal set of variables to represent it. Moreover the approach as defined allows to apply the modelled variability to different blades, e.g. different stators or rotors, utilizing the nominal geometry as input. The aeroelastic analyses considering geometry based mistuning is carried on a test-rig case, focusing on how such variability can affect the modal forcing generated on the blades. A validated CFD model is used to extract the force generated by the unsteady pressure field over the selected vibrational mode shapes of the rotor blades. The blade mode shapes are extracted form a FEM model of the whole blisk and the blades displacements are mapped over the CFD model nodes. The uncertainty quantification of the geometrical variability effect on the modal forcing is performed utilizing Monte Carlo methods. A reduced model for the CFD solution is employed, utilizing a single passage multi blade row which assumes a time-space periodicity solving the governing equations in the frequency domain. This allows for conducting an uncertainty quantification considering the large domain of the variables used to describe the geometries compared to the computational resources needed for the single solution. The unsteady modal forcing is studied as amplitude and phase shift for the different engine orders (frequencies arising from the engine working condition as higher harmonics of the shaft speed). In particular the scatter of the main engine orders forcing amplitudes for the manufactured blades can be compared with the nominal responses to predict the possible amplification due to the geometrical variability. Finally the results are compared to a larger computational model to assess the influence of multiple variable blades in the assembly.}, language = {en} } @misc{WeberKuehhornKlaukeetal., author = {Weber, Robby and K{\"u}hhorn, Arnold and Klauke, Thomas and Schrape, Sven}, title = {The Effect of Sand Erosion on a Compressor Blade and its Modal Properties}, series = {Proceedings of ASME Turbo Expo 2020, Turbomachinery Technical Conference and Exposition, GT2020, September 21-25, 2020, Virtual, Online}, journal = {Proceedings of ASME Turbo Expo 2020, Turbomachinery Technical Conference and Exposition, GT2020, September 21-25, 2020, Virtual, Online}, pages = {9}, abstract = {The wear and damage of High-Pressure Compressor (HPC) blades due to erosion or Foreign Object Damage (FOD) have a significant influence on HPC aerodynamic performance, vibration resistance against High-Cycle Fatigue (HCF) and thus component lifetime. The changes in airfoil geometry reduce the overall engine efficiency. Furthermore extended off-wing engine maintenances due to blade failures are increasing the cost of ownership. The safe operation of every engine within a reduced number of shop visits requires a reliable prediction of future deterioration. This enables the optimization of services and off-wing time. One contribution to this is a better understanding of the component's dynamics and based on this providing an improved wear modeling to reliably predict the remaining lifetime and the decreased efficiency. This contribution determines the material removal of HPC blades due to sand erosion. Originally, this stage was built as a blisk (Blade Integrated Disk). After sand erosion test completion, the blisk was cut into segments containing one airfoil only. First, the material removal is determined for ten blades of one exemplary rotor. A blue light fringe projector is employed to identify the geometrical differences between the eroded blades and the nominal design. Second, realistic finite element models are generated to enable comparable modal analyses of eroded blades. This procedure suffers from unavoidable and mostly random imperfections due to the manufacturing process, which significantly affects the blade surface before the erosion test can be conducted. Therefore, an already published approach is implemented in the third step to predict the blade surface after erosion based on nominal blade design. The investigation is completed by comparing measured and predicted surfaces. Finally, the aforementioned tool is employed to predict the locations and intensities of the material losses and the accompanying change in modal properties of this compressor blade concerning operational time.}, language = {de} }