@misc{IssayevGiriElbazetal., author = {Issayev, Gani and Giri, Binod Raj and Elbaz, Ayman M. and Shrestha, Krishna Prasad and Mauß, Fabian and Roberts, William L. and Farooq, Aamir}, title = {Ignition delay time and laminar flame speed measurements of ammonia blended with dimethyl ether: A promising low carbon fuel blend}, series = {Renewable Energy}, volume = {181}, journal = {Renewable Energy}, issn = {1879-0682}, doi = {10.1016/j.renene.2021.09.117}, pages = {1353 -- 1370}, abstract = {Ammonia (NH3) has recently received much attention as a promising future fuel for mobility and power generation. The use of ammonia as a fueling vector can help curb global warming by cutting CO2 emissions because it is a carbon-free fuel and a hydrogen carrier with a high percentage of hydrogen atoms per unit volume. Liquid ammonia contains a higher volumetric density of hydrogen than liquid hydrogen. The low reactivity of ammonia, however, hinders its direct usage as a combustible fuel. One feasible way to boost the reactivity of ammonia is to target a dual-fuel system comprising of ammonia and a suitable combustion promoter. In this work, combustion properties of ammonia were investigated by blending it with various proportions of dimethyl ether (DME) using a rapid compression machine (RCM) and a constant volume spherical reactor (CVSR) over a wide range of experimental conditions. DME is a highly reactive fuel that may be produced in a sustainable carbon cycle with a net zero-carbon emission. Ignition delay times (IDTs) of NH3/DME blends were measured over a temperature (T) range of 649e950 K, pressures (P) of 20 and 40 bar, equivalence ratios (F) of 0.5 and 1 for a range of DME mole fractions (cDME) of 0.05e0.5 in the blends. In addition, the laminar burning velocities of NH3/DME blends were measured at P ¼ 1, 3 and 5 bar, F ¼ 0.8e1.3 and T ¼ 300 K for cDME ranging from 0.18 to 0.47. Our results suggest that DME is a good ignition promoter, resulting in a significant shortening of IDTs and an increase of flame speeds of NH3. A detailed chemical model has been developed and validated against the experimental data. Overall, our kinetic model offered reasonable predictive capabilities capturing the experimental trends over a wide range of conditions. In the worst-case scenario, our model underpredicted IDTs by a factor of ~2.5 while overpredicting laminar flame speed by ~20\%.}, language = {en} } @misc{ShresthaGiriElbazetal., author = {Shrestha, Krishna Prasad and Giri, Binod Raj and Elbaz, Ayman M. and Issayev, Gani and Roberts, William L. and Seidel, Lars and Mauß, Fabian and Farooq, Aamir}, title = {A detailed chemical insights into the kinetics of diethyl ether enhancing ammonia combustion and the importance of NOx recycling mechanism}, series = {Fuel Communications}, volume = {10}, journal = {Fuel Communications}, issn = {2666-0520}, doi = {10.1016/j.jfueco.2022.100051}, pages = {18}, abstract = {In this work, we investigated the combustion characteristics of ammonia (NH3) by blending it with various proportions of diethyl ether (DEE). We measured laminar flame speed of various NH3/DEE blends (DEE, 10-40\% by mole) using a constant volume spherical vessel at Ti = 298 K and Pi = 3 and 5 bar and Φ = 0.8-1.3. We developed a detailed kinetic model to describe the trends of the current and previously published experimental data. For the robustness of the model, we first developed a comprehensive diethyl ether kinetic mechanism to accurately characterize neat DEE oxidation behavior. We validated the kinetic model using a large pool of experimental data comprising shock tube, rapid compression machine, jet-stirred and flow reactors, freely propagating, and burner-stabilized premixed flames. The developed kinetic model performs remarkably in capturing the combustion behavior of pure DEE and NH3. Importantly, our model captures the experimental data of laminar flame speed and ignition delay times of various NH3/DEE blends over a wide range of conditions. We found that DEE is a promising candidate to promote the combustion characteristics of NH3. A small portion of DEE (10\%) enhances the laminar flame speed of NH3 by a factor of 2 at Pi = 1 bar, Ti = 298 K, and Φ = 1.0. A further doubling of the DEE mole fraction to 20\% did not enhance the laminar flame speed of NH3 with the same propensity. At low temperatures, adding 5\% DEE in NH3 blend has significantly expedited the system reactivity by lowering the autoignition temperature. A further 5\% increment of DEE (i.e., 10\% DEE in NH3) lowers the autoignition temperature by ∼120 K to achieve the same ignition delay time. The "NOsingle bondNO2" looping mechanism predominantly drives such reactivity accelerating effect. Here, the reactions, NO + HO2 = NO2 + OH and NO2 + H = NO + OH, appear to enhance the reactive radical pool by generating OH radicals. We observed that the HNO path is favored more with increasing DEE content which eventually liberates NO. Other key reactions in "NOsingle bondNO2" looping mechanism are: CH3 + NO2 = CH3O + NO, CH3O2 + NO = CH3O + NO2, C2H5 + NO2 = C2H5O + NO, C2H5O2 + NO = C2H5O + NO2. In addition, CH3 + NH2(+M) = CH3NH2(+M) reaction is also one of the important cross-reactions which leads to the formation of HCN. Therefore, cross-reactions between the nitrogen and carbon family are crucial in accurately predicting autoignition timing. This work provides a detailed chemical insight into the NH3 and DEE interaction, which could be applied to other fuel blends of NH3. The kinetic model is also validated for several C1single bondC3 fuels including their interaction with NOx.}, language = {en} } @misc{RakhiShresthaGuentheretal., author = {Rakhi, Rakhi and Shrestha, Krishna Prasad and G{\"u}nther, Vivien and Mauß, Fabian}, title = {Thermodynamic analysis to develop a detailed surface reaction mechanism}, series = {Fuel Science - From Production to Propulsion, Aachen, Germany, May 2022}, journal = {Fuel Science - From Production to Propulsion, Aachen, Germany, May 2022}, pages = {2}, abstract = {The reduction of greenhouse gasses such as CO2 and CH4 is becoming necessary due to global environmental problems. The reforming of light hydrocarbons is a particularly efficient process for producing synthesis gas, H2 and CO, from greenhouse gasses [1]. The steam reforming of methane is the most important method to produce syngas in industry by using a nickel catalyst. Nickel-based catalysts are the conventional catalysts in industrial applications due to their fast turnover rates, good availability, and low costs, however, limited by their tendency towards coke formation. In this study, a detailed surface reaction mechanism is developed for steam reform-ing of methane over nickel and results are compared with the reference data.}, language = {en} } @misc{FrankenSrivastavaLeeetal., author = {Franken, Tim and Srivastava, Vivek and Lee, Sung-Yong and Heuser, Benedikt and Shrestha, Krishna Prasad and Seidel, Lars and Mauß, Fabian}, title = {Numerical Analysis of the Combustion of Diesel, Dimethyl Ether, and Polyoxymethylene Dimethyl Ethers (OMEn, n=1-3) Using Detailed Chemistry}, series = {THIESEL 2022 : Conference on Thermo- and Fluid-Dynamics of Clean Propulsion Powerplants, 13th-16th September 2022 : conference proceedings}, journal = {THIESEL 2022 : Conference on Thermo- and Fluid-Dynamics of Clean Propulsion Powerplants, 13th-16th September 2022 : conference proceedings}, editor = {Xandra, Margot and Payri, Ra{\´u}l and Serrano, Jos{\´e} Ram{\´o}n}, publisher = {Editorial Universitat Polit{\`e}cnica de Val{\`e}ncia}, address = {Val{\`e}ncia}, isbn = {978-84-1396-055-5}, doi = {10.4995/Thiesel.2022.632801}, abstract = {New types of synthetic fuels are introduced in internal combustion engine applications to achieve carbon-neutral and ultra-low emission combustion. Dimethyl Ether (DME) and Polyoxymethylene Dimethyl Ethers (OMEn) belong to such kind of synthetic fuels. Recently, Shrestha et al. (2022) have developed a novel detailed chemistry model for OMEn (n=1-3) to predict the ignition delay time, laminar flame speed and species formation for various thermodynamic conditions. The detailed chemistry model is applied in the zero dimensional (0D) stochastic reactor model (DI-SRM) to investigate the non-premixed combustion in a 2-liter diesel engine. Further insights in the formation of unburned hydrocarbons (HC), carbon monoxide and nitrogen oxides during the combustion of OMEn fuels are obtained in this work. The combustion and emission formation of DME and OMEn (n=1-3) are investigated and compared to conventional Diesel combustion. The mixture formation is governed by an earlier vaporization of the DME and OMEn fuels, faster homogenization of the respective air-fuel mixture and higher reactivity. At the same injection pressure, the OMEn fuels obtain higher NOx but lower CO and HC emissions. High amounts of aromatics, ethene, methane formaldehyde and formic acid are found within the Diesel exhaust gas. The DME and OMEn exhaust gas contains higher fractions of formaldehyde and formic acid, and fractions of methane, methyl formate and nitromethane.}, language = {en} } @misc{FrankenShresthaSeideletal., author = {Franken, Tim and Shrestha, Krishna Prasad and Seidel, Lars and Mauß, Fabian}, title = {Effect of Gasoline-Ethanol-Water Mixtures on Auto-Ignition in a Spark Ignition Engine}, series = {International Conference on Knocking in Gasoline Engines}, journal = {International Conference on Knocking in Gasoline Engines}, editor = {Sens, Marc}, publisher = {expert}, address = {T{\"u}bingen}, isbn = {978-3-8169-3544-5}, doi = {10.24053/9783816985440}, pages = {175 -- 222}, abstract = {The climate protection plan of the European Union requires a significant reduction of CO2 emissions from the transportation sector by 2030. Today ethanol is already blended by 10vol-\% in gasoline and further increase of the ethanol content to 20vol-\% is discussed. During the ethanol production process, distillation and molecular sieving is required to remove the water concentration to achieve high-purity ethanol. However, hydrous ethanol can be beneficial to suppress knock of spark ignition engines. The hygroscopic nature of ethanol can allow to increase the water content in gasoline - water emulsions even more, without adding additional surfactants, and improve the thermal efficiency by optimized combustion phasing, while keeping the system complexity low. Hence, the effect of gasoline - ethanol - water mixtures on the auto-ignition in a single-cylinder spark ignition engine is investigated by using multi-dimensional simulation and detailed chemistry. The gasoline - ethanol mixtures are defined to keep the Research Octane Number constant, while the Motored Octane Number is decreasing. In total five surrogates are defined and investigated: E10 (10vol-\% ethanol-in-gasoline), E20, E30, E70 and E100. The water content is determined according to experimentally defined ternary diagrams that evaluated stable gasoline - ethanol - water emulsion at different gasoline - ethanol blending ratios. The auto-ignition modes of the surrogates are analyzed using the diagram, which determines if hotspots are within harmless deflagration or harmful developing detonation regime. The strongest auto-ignition is observed for the E10 surrogate, while increasing ethanol content reduces the surrogate reactivity and increases the resonance parameter. No auto-ignition of the unburnt mixture is observed for the E70 and E100 surrogates. The addition of hydrous ethanol decreased the excitation time of the surrogates, especially at low ethanol content, wherefor the reactivity parameter is significantly increased. The hotspots for E10, E20 and E30 surrogates with hydrous ethanol are found within the developing detonation regime, while hotspots of the E70 surrogate with hydrous ethanol are found in the transition regime. For the hydrous E100 surrogate no auto-ignition is predicted because of reduced temperature of the unburnt mixture due to water vaporization, which outweighs the increased reactivity due to water vapor addition.}, language = {en} } @misc{ShresthaEckartDrostetal., author = {Shrestha, Krishna Prasad and Eckart, Sven and Drost, Simon and Fritsche, Chris and Schießl, Robert and Seidel, Lars and Maas, Ulrich and Krause, Hartmut and Mauß, Fabian}, title = {A comprehensive kinetic modeling of oxymethylene ethers (OMEn, n= 1-3) oxidation-laminar flame speed and ignition delay time measurements}, series = {Combustion and Flame}, volume = {246}, journal = {Combustion and Flame}, issn = {1556-2921}, doi = {10.1016/j.combustflame.2022.112426}, abstract = {This work reports on the development and experimental validation of a detailed reaction mechanism for the oxidation of polyoxymethylene dimethyl ethers (OMEn, n = 1-3). The validation is done by constant-volume chamber laminar flame speeds (393 K and 443 K, 1 to 5 bar, and equivalence ratio 0.8 to 1.6) and Rapid Compression Machine ignition delay times (550-680 K, 10 and 15 bar, equivalence ratios of 0.5-2.0) in OMEn/air mixtures. Using our new experimental and published data, the validation basis for the new kinetic model comprises the pyrolysis and oxidation of OMEn (n = 1-3) in freely propagating flames, auto-ignition in rapid compression machines and shock tubes, and speciation in jet-stirred and flow reactors as well as burner-stabilized premixed flames. The model provides a reasonable agreement with the experimental data for a broad range of conditions investigated. The performance of the developed model is compared against the recent literature models. OMEn (n = 1-3) all have the same laminar flame speed. The model suggests that the chemistry of OME0 (DME) and CH3OCHO (methyl formate) is the one that dictates the flame chemistry. Under the same pressure and equivalence ratio conditions, ignition delay times of OME2 and OME3 are similar for the investigated temperature range. This work helps to improve the understanding of OMEs chemistry. The model developed in this work will serve as the base mechanism for higher chain length OMEs (n>3).}, language = {en} } @misc{ShresthaElbazGirietal., author = {Shrestha, Krishna Prasad and Elbaz, Ayman M. and Giri, Binod Raj and Arab, Omar Z. and Adil, Mohammad and Seidel, Lars and Roberts, William L. and Farooq, Aamir and Mauß, Fabian}, title = {Experimental and Kinetic Modeling Study of 1, 3-Dioxolane Oxidation and Comparison with Dimethoxymethane}, series = {Energy \& Fuels}, volume = {36}, journal = {Energy \& Fuels}, number = {14}, issn = {1520-5029}, doi = {10.1021/acs.energyfuels.2c01132}, pages = {7744 -- 7754}, abstract = {This work reports laminar flame speeds and ignition delay times of 1,3-dioxolane/O2/inert gases over a wide range of conditions. Laminar flame speeds were determined experimentally at pressures of 1 and 3 bar, the temperature of 300 K, and equivalence ratios ranging from 0.7 to 1.4 using a constant-volume spherical chamber, whereas ignition delay times were measured in a shock tube at a pressure of 1 bar, the temperature range of 1000-1265 K, and equivalence ratios of 0.5 and 1.0. A detailed kinetic model is developed to predict the oxidation of 1,3-dioxolane utilizing our new experimental data and published datasets on the oxidation of 1,3-dioxolane in freely propagating flames, autoignition in rapid compression machines and shock tubes, and speciation in a jet-stirred reactor. Model predictions are in reasonable agreement with the experimental data. Laminar flame speeds and ignition delay times of 1,3-dioxolane (cyclic ether) are compared with those of dimethoxymethane (acyclic ether). It is found that 1,3-dioxolane has a higher laminar flame speed than that of dimethoxymethane, which may be attributed to the formation of C2H4, C2H2, and the H atom from 1,3-dioxolane. On the contrary, ignition delay times of 1,3-dioxolane are longer than those of dimethoxymethane below 1000 K and shorter above 1000 K for the same dilution level. The reaction ȮCHO = CO2 + H is critical for accurately predicting 1,3-dioxolane oxidation, and it significantly influences model predictions under low-pressure conditions. The model developed in this work will serve as the base mechanism for higher cyclic and acyclic ethers.}, language = {en} } @misc{RossiBargendeKulzeretal., author = {Rossi, Edoardo and Bargende, Michael and Kulzer, Andr{\´e} Casal and Chiodi, Marco and Massoud, Ehab and Shrestha, Krishna Prasad and Mauß, Fabian}, title = {Analysis of the applicability of Water Injection in Combination with an eFuel for Knock Mitigation and Improved Engine Efficiency}, series = {SAE Technical Paper}, journal = {SAE Technical Paper}, issn = {2688-3627}, doi = {10.4271/2022-37-0019}, abstract = {The development of future gasoline engines is dominated by the study of new technologies aimed at reducing the engine negative environmental impact and increase its thermal efficiency. One common trend is to develop smaller engines able to operate in stoichiometric conditions across the whole engine map for better efficiency, lower fuel consumption, and optimal conversion rate of the three-way catalyst (TWC). Water injection is one promising technique, as it significantly reduces the engine knock tendency and avoids fuel enrichment for exhaust temperature mitigation at high power operation. With the focus on reducing the carbon footprint of the automotive sector, another vital topic of research is the investigation of new alternative CO2-neutral fuels or so-called eFuels. Several studies have already shown how these new synthetic fuels can be produced by exploiting renewable energy sources and can significantly reduce engine emissions. This work is part of the FVV project number 1367, "Water Injection in Spark-Ignition Engines II", which investigates the coexistence of two different engine technologies that heads towards the same direction of sustainability of the internal combustion engine: water injection and eFuels. The goal is to assess the advantages that the adoption of an eFuel in combination with water injection strategies can bring, with respect to the same strategies applied in combination with commercial gasoline. Several water injection strategies, including direct water injection, indirect water injection, injection timing, and pressure variations, are considered for a better understanding of the benefits brought by the combination of an eFuel with water injection. For this purpose, experimental tests and 3D-CFD engine simulations have been performed. The physical properties of the investigated eFuel have been experimentally measured for accurate modelling in the simulation environment, and the thermodynamic properties have been evaluated utilizing detailed chemistry calculations.}, language = {en} } @misc{RakhiShresthaGuentheretal., author = {Rakhi, Rakhi and Shrestha, Krishna Prasad and G{\"u}nther, Vivien and Mauß, Fabian}, title = {Kinetically consistent detailed surface reaction mechanism for steam reforming of methane over nickel catalyst}, series = {Reaction Kinetics, Mechanisms and Catalysis}, volume = {135}, journal = {Reaction Kinetics, Mechanisms and Catalysis}, number = {6}, issn = {1878-5204}, doi = {10.1007/s11144-022-02314-7}, pages = {3059 -- 3083}, language = {en} }