@misc{ElbazGiriIssayevetal., author = {Elbaz, Ayman M. and Giri, Binod Raj and Issayev, Gani and Shrestha, Krishna Prasad and Mauß, Fabian and Farooq, Aamir and Roberts, William L.}, title = {Experimental and Kinetic Modeling Study of Laminar Flame Speed of Dimethoxymethane and Ammonia Blends}, series = {Energy \& Fuels}, volume = {34}, journal = {Energy \& Fuels}, number = {11}, issn = {1520-5029}, doi = {10.1021/acs.energyfuels.0c02269}, pages = {14727 -- 14740}, abstract = {Ammonia (NH3) is considered a promising carbon-neutral fuel, with a high hydrogen content, that can diversify the global energy system. Blending ammonia with a highly reactive fuel is one possible strategy to enhance its combustion characteristics. Here, an investigation of blends of NH3 and dimethoxymethane (DMM), a biofuel with high fuel-born oxygen content and no carbon-carbon bonds, is reported. Unstretched laminar burning velocity (SL) and Markstein length of different NH3/DMM blends were experimentally determined using spherically propagating premixed flames. The DMM mole fraction was varied from 0.2 to 0.6 while measuring SL at 298 K, 0.1 MPa, and equivalence ratios (Φ) over the range of 0.8-1.3. The addition of DMM was found to immensely enhance the combustion characteristics of ammonia. DMM 20\% (by mole fraction) in the NH3/DMM blend increased SL by more than a factor of 3 over neat ammonia; such enhancement was found to be comparable to 60\% CH4 in NH3 (Φ = 0.9-1.1) blends. Increasing Φ was found to significantly decrease the burned gas Markstein length for lean cases, whereas a negligible effect was observed for rich mixtures. A composite chemical kinetic model of DMM/NH3, aimed at interpreting the high-temperature combustion chemistry, was able to reliably predict SL for neat NH3 and DMM flames. Also, the predictive capability of the kinetic model to describe SL for DMM/NH3 blends is reasonably good. Sensitivity analysis and reaction path analysis indicated that the NH3/DMM blends could be understood as dual oxidation processes of the individual fuels that are competing for the same radical pool.}, language = {en} } @misc{IssayevGiriElbazetal., author = {Issayev, Gani and Giri, Binod Raj and Elbaz, Ayman M. and Shrestha, Krishna Prasad and Mauß, Fabian and Roberts, William L. and Farooq, Aamir}, title = {Ignition delay time and laminar flame speed measurements of ammonia blended with dimethyl ether: A promising low carbon fuel blend}, series = {Renewable Energy}, volume = {181}, journal = {Renewable Energy}, issn = {1879-0682}, doi = {10.1016/j.renene.2021.09.117}, pages = {1353 -- 1370}, abstract = {Ammonia (NH3) has recently received much attention as a promising future fuel for mobility and power generation. The use of ammonia as a fueling vector can help curb global warming by cutting CO2 emissions because it is a carbon-free fuel and a hydrogen carrier with a high percentage of hydrogen atoms per unit volume. Liquid ammonia contains a higher volumetric density of hydrogen than liquid hydrogen. The low reactivity of ammonia, however, hinders its direct usage as a combustible fuel. One feasible way to boost the reactivity of ammonia is to target a dual-fuel system comprising of ammonia and a suitable combustion promoter. In this work, combustion properties of ammonia were investigated by blending it with various proportions of dimethyl ether (DME) using a rapid compression machine (RCM) and a constant volume spherical reactor (CVSR) over a wide range of experimental conditions. DME is a highly reactive fuel that may be produced in a sustainable carbon cycle with a net zero-carbon emission. Ignition delay times (IDTs) of NH3/DME blends were measured over a temperature (T) range of 649e950 K, pressures (P) of 20 and 40 bar, equivalence ratios (F) of 0.5 and 1 for a range of DME mole fractions (cDME) of 0.05e0.5 in the blends. In addition, the laminar burning velocities of NH3/DME blends were measured at P ¼ 1, 3 and 5 bar, F ¼ 0.8e1.3 and T ¼ 300 K for cDME ranging from 0.18 to 0.47. Our results suggest that DME is a good ignition promoter, resulting in a significant shortening of IDTs and an increase of flame speeds of NH3. A detailed chemical model has been developed and validated against the experimental data. Overall, our kinetic model offered reasonable predictive capabilities capturing the experimental trends over a wide range of conditions. In the worst-case scenario, our model underpredicted IDTs by a factor of ~2.5 while overpredicting laminar flame speed by ~20\%.}, language = {en} }