@misc{MandalMuellerHenkeletal., author = {Mandal, Dipankar and M{\"u}ller, Klaus and Henkel, Karsten and Schmeißer, Dieter}, title = {The effect of X-ray photoelectron spectroscopy measurement on P(VDF-TrFE) copolymer thin films}, series = {Applied Surface Science}, journal = {Applied Surface Science}, number = {261}, issn = {0169-4332}, doi = {10.1016/j.apsusc.2012.07.144}, pages = {209 -- 213}, abstract = {The impact of prolonged X-ray irradiation during X-ray photoelectron spectroscopy (XPS) measurement was investigated on poly(vinylidene-trifluoroethylene) (P(VDF-TrFE)) thin films. It was observed that prolonged X-ray irradiation can accelerate the crosslinking of P(VDF-TrFE) and diminish the ferroelectric phase. Fourier transform infrared spectroscopy (FT-IR) data indicate that the ferroelectric phase diminishes completely after 360 kJ of X-ray irradiation dose and it induces the paraelectric phase. In this work, the main emphasis was given to the optimization of the X-ray irradiation dose during XPS measurements to maintain the ferroelectric phase within the copolymer films.}, language = {en} } @misc{HaeberleHenkelGargourietal., author = {Haeberle, J{\"o}rg and Henkel, Karsten and Gargouri, Hassan and Naumann, Franziska and Gruska, Bernd and Arens, Michael and Tallarida, Massimo and Schmeißer, Dieter}, title = {Ellipsometry and XPS comparative studies of thermal and plasma enhanced atomic layer deposited Al2O3-films}, series = {Beilstein Journal of Nanotechnology}, volume = {2013}, journal = {Beilstein Journal of Nanotechnology}, number = {4}, issn = {2190-4286}, doi = {10.3762/bjnano.4.83}, pages = {732 -- 742}, abstract = {We report on results on the preparation of thin (<100 nm) aluminum oxide (Al2O3) films on silicon substrates using thermal atomic layer deposition (T-ALD) and plasma enhanced atomic layer deposition (PE-ALD) in the SENTECH SI ALD LL system. The T-ALD Al2O3layers were deposited at 200 °C, for the PE-ALD films we varied the substrate temperature range between room temperature (rt) and 200 °C. We show data from spectroscopic ellipsometry (thickness, refractive index, growth rate) over 4" wafers and correlatethem to X-ray photoelectron spectroscopy (XPS) results. The 200°C T-ALD and PE-ALD processes yield films with similar refractive indices and with oxygen to aluminum elemental ratios very close to the stoichiometric value of 1.5. However, in both also fragments of the precursor are integrated into the film. The PE-ALD films show an increased growth rate and lower carbon contaminations. Reducing the deposition temperature down to rt leads to a higher content of carbon and CH-species. We also find a decrease of the refractive index and of the oxygen to aluminum elemental ratio as well as an increase of the growth rate whereas the homogeneity of the film growth is not influenced significantly. Initial state energy shifts in all PE-ALD samples are observed which we attribute to a net negative charge within the films.}, language = {en} } @misc{HenkelGargouriGruskaetal., author = {Henkel, Karsten and Gargouri, Hassan and Gruska, Bernd and Arens, Michael and Tallarida, Massimo and Schmeißer, Dieter}, title = {Capacitance and conductance versus voltage characterization of Al2O3 layers prepared by PE-ALD at 25°C ≤ T ≤ 200°C}, series = {Journal of Vacuum Science and Technology A}, volume = {1}, journal = {Journal of Vacuum Science and Technology A}, number = {32}, doi = {10.1116/1.4831897}, pages = {01A107-1 -- 01A107-10}, abstract = {In this work, plasma enhanced atomic layer deposited (PE-ALD) samples were prepared at substrate temperatures in the range between room temperature (RT) and 200 °C and investigated by capacitance-voltage and conductance-voltage recordings. The measurements are compared to standard thermal atomic layer deposition (T-ALD) at 200 °C. Very low interface state density (D it) ~1011 eV-1 cm-2 could be achieved for the PE-ALD process at 200 °C substrate temperature after postdeposition anneal (PDA) in forming gas at 450 °C. The PDA works very effectively for both the PE-ALD and T-ALD at 200 °C substrate temperature delivering also similar values of negative fixed charge density (N fix) around -2.5 × 1012 cm-2. At the substrate temperature of 150 °C, highest N fix (-2.9 × 1012 cm-2) and moderate D it (2.7 × 1011 eV-1 cm-2) values were observed. The as deposited PE-ALD layer at RT shows both low D it in the range of (1 to 3) × 1011 eV-1 cm-2 and low N fix (-4.4 × 1011 cm-2) at the same time. The dependencies of N fix, D it, and relative permittivity on the substrate temperatures and its adjustability are discussed.}, language = {en} } @misc{MandalHenkelSchmeisser, author = {Mandal, Dipankar and Henkel, Karsten and Schmeißer, Dieter}, title = {Improved performance of a polymer nanogenerator based on silver nanoparticles doped electrospun P(VDF-HFP) nanofibers}, series = {Physical Chemistry Chemical Physics}, volume = {2014}, journal = {Physical Chemistry Chemical Physics}, number = {16}, issn = {1463-9084}, doi = {10.1039/C3CP55238A}, pages = {10403 -- 10407}, abstract = {We report on the electrospinning of poly(vinylidene fluoride-hexafluoropropylene) [P(VDF-HFP)] nanofibers doped with silver nanoparticles for the preparation of a polymer based nanogenerator (PNG). It has been found that the yield of the piezoelectric phase is increased by the addition of silver nanoparticles. Furthermore, defects in the P(VDF-HFP) electrospun fibers are removed resulting in a significant enhancement in the output power of the PNG. A maximum generated PNG output voltage of 3 V with a current density of 0.9 μA cm-2 is achieved.}, language = {en} } @misc{DasHenkelTallaridaetal., author = {Das, Chittaranjan and Henkel, Karsten and Tallarida, Massimo and Schmeißer, Dieter and Gargouri, Hassan and K{\"a}rkk{\"a}nen, Irina and Schneidewind, Jessica and Gruska, Bernd and Arens, Michael}, title = {Thermal and plasma enhanced atomic layer deposition of TiO2: Comparison of spectroscopic and electric properties}, series = {Journal of Vacuum Science and Technology A}, volume = {2015}, journal = {Journal of Vacuum Science and Technology A}, number = {33}, issn = {1520-8559}, doi = {10.1116/1.4903938}, pages = {01A144-1 -- 01A144-8}, abstract = {Titanium oxide (TiO2) deposited by atomic layer deposition (ALD) is used as a protective layer in photocatalytic water splitting system as well as a dielectric in resistive memory switching. The way ALD is performed (thermally or plasma-assisted) may change the growth rate as well as the electronic properties of the deposited films. In the present work, the authors verify the influence of the ALD mode on functional parameters, by comparing the growth rate and electronic properties of TiO2 films deposited by thermal (T-) and plasma-enhanced (PE-) ALD. The authors complete the study with the electrical characterization of selected samples by means of capacitance-voltage and current-voltage measurements. In all samples, the authors found a significant presence of Ti3+ states, with the lowest content in the PE-ALD grown TiO2 films. The observation of Ti3+ states was accompanied by the presence of in-gap states above the valence band maximum. For films thinner than 10 nm, the authors found also a strong leakage current. Also in this case, the PE-ALD films showed the weakest leakage currents, showing a correlation between the presence of Ti3+ states and leakage current density.}, language = {en} } @misc{GarainSinhaAdhikaryetal., author = {Garain, Samiran and Sinha, Tridib Kumar and Adhikary, Prakriti and Henkel, Karsten and Sen, Shrabanee and Ram, Shanker and Sinha, Chittaranjan and Schmeißer, Dieter and Mandal, Dipankar}, title = {Self-Poled Transparent and Flexible UV Light-Emitting Cerium Complex-PVDF Composite: A High-Performance Nanogenerator}, series = {ACS Applied Materials \& Interfaces}, volume = {2015}, journal = {ACS Applied Materials \& Interfaces}, number = {7}, issn = {1944-8244}, doi = {10.1021/am507522r}, pages = {1298 -- 1307}, abstract = {Cerium(III)-,N-dimethylformamide-bisulfate [Ce(DMF)(HSO4)3] complex is doped into poly(vinylidene fluoride) (PVDF) to induce a higher yield (99\%) of the electroactive phases (β- and γ-phases) of PVDF. A remarkable enhancement of the output voltage (∼32 V) of a nano-generator (NG) based on a nonelectrically poled cerium(III) complex containing PVDF composite film is achieved by simple repeated human finger imparting, whereas neat PVDF does not show this kind of behavior. This high electrical output resembles the generation of self-poled electroactiveβ-phase in PVDF due to the electrostatic interactions between the fluoride of PVDF and the surface-active positive charge cloud of the cerium complex via H-bonding and/or bipolar interaction among the opposite poles of cerium complex and PVDF, respectively. The capacitor charging capability of the flexible NG promises its applicability as piezoelectric-based energy harvester. The cerium(III) complex doped PVDF composite film exhibit an intense photoluminescence in the UV region, which might be due to a participation of electron cloud from negative pole of bipolarized PVDF. This fact may open a new area for prospective development of high-performance energy-saving flexible solid-state UV light emitters.}, language = {en} } @misc{TamangGhoshGarainetal., author = {Tamang, Abiral and Ghosh, Sujoy Kumar and Garain, Samiran and Alam, Md. Mehebub and Haeberle, J{\"o}rg and Henkel, Karsten and Schmeißer, Dieter and Mandal, Dipankar}, title = {DNA-Assisted β‑phase Nucleation and Alignment of Molecular Dipoles in PVDF Film: A Realization of Self-Poled Bioinspired Flexible Polymer Nanogenerator for Portable Electronic Devices}, series = {ACS Applied Materials \& Interfaces}, journal = {ACS Applied Materials \& Interfaces}, number = {7}, issn = {1944-8244}, doi = {10.1021/acsami.5b04161}, pages = {16143 -- 16147}, abstract = {A flexible nanogenerator (NG) is fabricated with a poly(vinylidene fluoride) (PVDF)film, where deoxyribonu-cleic acid (DNA) is the agent for the electroactive β-phase nucleation. Denatured DNA is co-operating to align the molecular-CH2/-CF2 dipoles of PVDF causing piezo- electricity without electrical poling. The NG is capable of harvesting energy from a variety of easily accessible mechanical stress such as human touch, machine vibration, football juggling, and walking. The NG exhibits high piezoelectric energy conversion efficiency facilitating the instant turn-on of several green or blue light-emitting diodes. The generated energy can be used to charge capacitors providing a wide scope for the design of self-powered portable devices.}, language = {en} } @misc{SowińskaHenkelSchmeisseretal., author = {Sowińska, Małgorzata and Henkel, Karsten and Schmeißer, Dieter and K{\"a}rkk{\"a}nen, Irina and Schneidewind, Jessica and Naumann, Franziska and Gruska, Bernd and Gargouri, Hassan}, title = {Plasma-enhanced atomic layer deposition of titanium oxynitrides films: A comparative spectroscopic and electrical study}, series = {Journal of Vacuum Science and Technology A}, journal = {Journal of Vacuum Science and Technology A}, number = {34}, issn = {0734-2101}, doi = {10.1116/1.4936227}, pages = {01A127-1 -- 01A127-9}, abstract = {The process parameters' impact of the plasma-enhanced atomic layer deposition (PE-ALD) method on the oxygen to nitrogen (O/N) ratio in titanium oxynitride (TiOxNy) films was studied. Titanium(IV)isopropoxide in combination with NH3 plasma and tetrakis(dimethylamino) titanium by applying N2 plasma processes were investigated. Samples were characterized by the in situ spectroscopic ellipsometry, x-ray photoelectron spectroscopy, and electrical characterization (current-voltage: I-V and capacitance-voltage: C-V) methods. The O/N ratio in the TiOxNy films is found to be very sensitive for their electric properties such as conductivity, dielectric breakdown, and permittivity. Our results indicate that these PE-ALD film properties can be tuned, via the O/N ratio, by the selection of the process parameters and precursor/coreactant combination.}, language = {en} } @misc{SowinskaBrizziDasetal., author = {Sowinska, Małgorzata and Brizzi, Simone and Das, Chittaranjan and K{\"a}rkk{\"a}nen, Irina and Schneidewind, Jessica and Naumann, Franziska and Gargouri, Hassan and Henkel, Karsten and Schmeißer, Dieter}, title = {Analysis of nitrogen species in titanium oxynitride ALD films}, series = {Applied Surface Science}, volume = {381}, journal = {Applied Surface Science}, issn = {0169-4332}, doi = {10.1016/j.apsusc.2016.02.096}, pages = {42 -- 47}, abstract = {Titanium oxynitride films are prepared by plasma enhanced atomic layer deposition method using two different precursors and nitrogen sources. Synchrotron radiation-based X-ray photoelectron spectroscopy and X-ray absorption spectroscopy are used to characterize the nitrogen species incorporated within these films depending on the deposition parameters. It is found that nitrogen atoms in these films are differently bonded. In particular, it can be distinguished between Ti-ON and Ti-N bonding configurations and molecular nitrogen species caused by precursor fragments.}, language = {en} } @misc{DasKotHenkeletal., author = {Das, Chittaranjan and Kot, Małgorzata and Henkel, Karsten and Schmeißer, Dieter}, title = {Engineering of Sub-Nanometer SiOₓ Thickness in Si Photocathodes for Optimized Open Circuit Potential}, series = {ChemSusChem}, volume = {9}, journal = {ChemSusChem}, number = {17}, issn = {1864-5631}, doi = {10.1002/cssc.201600777}, pages = {2332 -- 2336}, abstract = {Silicon is one of the most promising materials to be used for tandem-cell water-splitting devices. However, the electrochemical instability of bare Si makes it difficult to be used for stable devices. Besides that, the photovoltage loss in Si, caused by several factors (e.g., metal oxide protection layer and/or SiO₂/Si or catalyst/Si interface), limits its use in these devices. In this work, we present that an optimized open circuit potential (OCP) of Si can be obtained by controlling the SiOₓ thickness in sub-nanometer range. It can be done by means of a simple and cost-effective way using the combination of a wet chemical etching and the low temperature atomic layer deposition (ALD) of TiO₂. We have found that a certain thickness of the native SiOₓ is necessary to prevent further oxidation of the Si photocathode during the ALD growth of TiO₂. Moreover, covering the Si photocathode with an ALD TiO₂ layer enhances its stability.}, language = {en} }