@misc{MahmoodinezhadMoralesNaumannetal., author = {Mahmoodinezhad, Ali and Morales, Carlos and Naumann, Franziska and Plate, Paul and Meyer, Robert and Janowitz, Christoph and Henkel, Karsten and Kot, Małgorzata and Flege, Jan Ingo}, title = {Low-temperature atomic layer deposition of indium oxide thin films using trimethylindium and oxygen plasma}, series = {Verhandlungen der DPG - SurfaceScience21}, volume = {2021}, journal = {Verhandlungen der DPG - SurfaceScience21}, publisher = {Deutsche Physikalische Gesellschaft e.V.}, address = {Bad Honnef}, abstract = {Indium oxide thin films were deposited on Si (100) by plasma-enhanced atomic layer deposition (PEALD) using trimethylindium (TMIn) and oxygen plasma (O2) in a low-temperature range of 80 to 200 °C. The In2O3 layers were characterized by in-situ spectroscopic ellipsometry (SE), ex-situ X-ray photoelectron spectroscopy (XPS) and electrical measurements. The SE data show a growth rate of 0.56 {\AA}/cycle within the ALD window (100 to 150 °C) with a thickness inhomogeneity of ≤1.2\%. In addition, the highest refractive index is 2.07 (at 632.8 nm) for the layer grown at 150 °C, and the films exhibit indirect and direct band gaps of 2.8±0.1 eV and 3.3±0.2 eV, respectively. XPS characterization indicates no carbon incorporation and a temperature-dependent off-stoichiometry of the layers. The chemical analysis of the In 3d and O 1s core levels confirms the formation of In-O bonds and suggests the additional presence of hydroxyl groups and defects. With increasing temperature, the contribution of OH groups and defects decreases whereas that of In-O bonds increases. Notably, higher growth temperatures result in an indium rich phase within the layers.}, language = {en} } @misc{MoralesMahmoodinezhadSchubertetal., author = {Morales, Carlos and Mahmoodinezhad, Ali and Schubert, Andreas Markus and Wenger, Christian and Henkel, Karsten and Flege, Jan Ingo}, title = {Functional ultra-thin oxide films deposited by atomic layer deposition on structured substrates}, series = {Verhandlungen der DPG - SurfaceScience21}, volume = {2021}, journal = {Verhandlungen der DPG - SurfaceScience21}, publisher = {Deutsche Physikalische Gesellschaft e.V.}, address = {Bad Honnef}, abstract = {In the last decades, atomic layer deposition (ALD) has gained prominence in the materials and surface science communities owing to its high potential for integration as a scalable process in microelectronics. ALD's largest strengths are its well-controlled layer-by-layer deposition and growth conformity on 3D structures. Yet, the ALD technique is also well known to lead to amorphous and defective, non-stoichiometric thin films, resulting in modified materials properties that may even preferentially be used in certain applications. To study these issues, we have developed an in-situ ALD reactor attached to an X-ray photoelectron spectroscopy (XPS) system, capable of switching between both pump and flow-type operation. This novel tool allows to cover the entire range of compounds and recipes used in ALD, thus clarifying the role of such defects at different deposition stages, growth conditions and film/substrate interfaces. To exemplify these sorts of studies, we show the deposition of Al2O3 5-10 nm films on nanostructured Si, and their use as substrates for functional CeOx ALD deposits.}, language = {en} } @misc{MahmoodinezhadMoralesNaumannetal., author = {Mahmoodinezhad, Ali and Morales, Carlos and Naumann, Franziska and Plate, Paul and Meyer, Robert and Janowitz, Christoph and Henkel, Karsten and Kot, Małgorzata and Z{\"o}llner, Marvin Hartwig and Wenger, Christian and Flege, Jan Ingo}, title = {Low-temperature atomic layer deposition of indium oxide thin films using trimethylindium and oxygen plasma}, series = {Journal of Vacuum Science and Technology A}, volume = {39}, journal = {Journal of Vacuum Science and Technology A}, number = {6}, issn = {0734-2101}, doi = {10.1116/6.0001375}, abstract = {Indium oxide (InxOy) thin films were deposited by plasma-enhanced atomic layer deposition (PEALD) using trimethylindium and oxygen plasma in a low-temperature range of 80-200 °C. The optical properties, chemical composition, crystallographic structure, and electrical characteristics of these layers were investigated by spectroscopic ellipsometry (SE), x-ray photoelectron spectroscopy (XPS), x-ray diffraction (XRD), as well as current-voltage and capacitance-voltage measurements. The SE results yielded a nearly constant growth rate of 0.56 {\AA} per cycle and a thickness inhomogeneity of ≤1.2\% across 4-in. substrates in the temperature range of 100-150 °C. The refractive index (at 632.8 nm) was found to be 2.07 for the films deposited at 150 °C. The PEALD-InxOy layers exhibit a direct (3.3 ± 0.2 eV) and an indirect (2.8 ± 0.1 eV) bandgap with an uptrend for both with increasing substrate temperature. Based on XPS characterization, all InxOy samples are free of carbon impurities and show a temperature-dependent off-stoichiometry indicating oxygen vacancies. XRD diffraction patterns demonstrate an onset of crystallization at 150 °C. Consistent with the optical, XPS, and XRD data, the films deposited at ≥150 °C possess higher electrical conductivity. Our findings prove that a low-temperature PEALD process of InxOy is feasible and promising for a high-quality thin-film deposition without chemical impurities on thermally fragile substrates.}, language = {en} } @misc{JanowitzMahmoodinezhadKotetal., author = {Janowitz, Christoph and Mahmoodinezhad, Ali and Kot, Małgorzata and Morales, Carlos and Naumann, Franziska and Plate, Paul and Z{\"o}llner, Marvin Hartwig and B{\"a}rwolf, Florian and Stolarek, David and Wenger, Christian and Henkel, Karsten and Flege, Jan Ingo}, title = {Toward controlling the Al2O3/ZnO interface properties by in situ ALD preparation}, series = {Dalton Transactions}, volume = {51}, journal = {Dalton Transactions}, issn = {1477-9234}, doi = {10.1039/D1DT04008A}, pages = {9291 -- 9301}, abstract = {An Al2O3/ZnO heterojunction was grown on a Si single crystal substrate by subsequent thermal and plasma-assisted atomic layer deposition (ALD) in situ. The band offsets of the heterointerface were then studied by consecutive removal of the layers by argon sputtering, followed by in situ X-ray photoelectron spectroscopy. The valence band maximum and conduction band minimum of Al2O3 are found to be 1.1 eV below and 2.3 eV above those of ZnO, resulting in a type-I staggered heterojunction. An apparent reduction of ZnO to elemental Zn in the interface region was detected in the Zn 2p core level and Zn L3MM Auger spectra. This suggests an interface formation different from previous models. The reduction of ZnO to Zn in the interface region accompanied by the creation of oxygen vacancies in ZnO results in an upward band bending at the interface. Therefore, this study suggests that interfacial properties such as the band bending as well as the valence and conduction band offsets should be in situ controllable to a certain extent by careful selection of the process parameters.}, language = {en} } @misc{TschammerKostoMoralesetal., author = {Tschammer, Rudi and Kosto, Yuliia and Morales, Carlos and Schmickler, Marcel and Henkel, Karsten and Devi, Anjana and Flege, Jan Ingo}, title = {Atomic layer deposition of cerium oxide monitored by operando ellipsometry and in-situ X-ray photoelectron spectroscopy}, series = {Verhandlungen der DPG}, journal = {Verhandlungen der DPG}, publisher = {Deutsche Physikalische Gesellschaft}, address = {Bad Honnef}, issn = {0420-0195}, abstract = {Atomic layer deposition (ALD) has been used extensively to grow homogeneous films with excellent coverage and atomic-scale thickness control for a variety of applications. However, remaining challenges include the investigation of novel precursor-oxidant combinations for low-temperature deposition as well as unraveling the complex interplay between substrate and coating for ultrathin films. In this work, we present a detailed investigation of ultrathin cerium oxide films grown using the novel Ce(dpdmg)3 precursor with H2O and O2. Following a surface science-based approach, we have combined operando spectroscopic ellipsometry and in-situ X-ray photoelectron spectroscopy to allow rapid process optimization and determination of the complex relation between oxide stoichiometry, film thickness and ALD growth parameters, revealing a distinct dependence of inital Ce3+ content on the film thickness and choice of oxidant. This offers the possibility of adjusting the oxide properties to application requirements e.g. in gas sensing by choosing a suitable precursor-oxidant combination.}, language = {en} } @misc{GertigMoralesHenkeletal., author = {Gertig, Max and Morales, Carlos and Henkel, Karsten and Flege, Jan Ingo}, title = {In situ X-ray photoelectron spectroscopy study of atomic layer deposited ceria on SiO2: substrate influence on the reaction mechanism during the early stages of growth}, series = {Verhandlungen der DPG}, journal = {Verhandlungen der DPG}, publisher = {Deutsche Physikalische Gesellschaft}, address = {Bad Honnef}, issn = {0420-0195}, abstract = {Atomic layer deposition (ALD) is known to produce amorphous and defect-rich films in a layer-by-layer fashion, which can potentially give rise to unexpected material properties. In particular, ultrathin films (few monolayers) will show the highest complexity, as the substrate-material interaction will play a major role during deposition. Therefore, it is crucial to understand the early stages of growth of the ALD process to control and potentially tailor this interfacial interaction. Applying a surface science approach combined with complementary ex-situ characterization, we have studied by in-situ X-ray photoelectron spectroscopy (XPS) the early stages of ceria (CeOx) growth on SiO2 substrates deposited by thermal-ALD using Ce(thd)4/O3. Interestingly, an initial mixture of Ce3+ and Ce4+ was observed, although only Ce4+ may be expected considering the used precursor and oxidant. This fact, together with a deviation from the ideal layer-by-layer growth and a higher growth rate during the first cycles, indicates a significant influence of the substrate of the ALD reaction mechanism as well as a correlation between morphology and ceria oxidation state.}, language = {en} } @misc{KostoKapuscikTschammeretal., author = {Kosto, Yuliia and Kapuscik, Paulina and Tschammer, Rudi and Guttmann, Dominic and Mankowska, Ewa and Matvija, Peter and Morales, Carlos and Mazur, Michał and Henkel, Karsten and Matolinova, Iva and Domaradzki, Jarosław and Flege, Jan Ingo}, title = {Bare and Pd-doped ceria thin films prepared by ALD and EBE for hydrogen detection}, series = {Verhandlungen der DPG}, journal = {Verhandlungen der DPG}, publisher = {Deutsche Physikalische Gesellschaft}, address = {Bad Honnef}, issn = {0420-0195}, abstract = {The need to store and use hydrogen safely as part of green economy based on renewable energy evokes a necessity to reliably detect it at ambient conditions. The majority of currently used sensors are working at elevated temperatures (200-500 °C). In this work, we demonstrate that ceria films deposited on a commercial electrode by atomic layer deposition (ALD) and electron beam evaporation (EBE) electrically respond to hydrogen (from 20 to 500 ppm) at much lower temperatures (50-200 °C). The results reveal that <1.5 nm thin Pd adlayer increases the electrical response by several orders of magnitude for both ceria films. The NAP-XPS study under changing oxidative/reductive atmospheres sheds light on the mechanism of Pd-CeOx thermal activation and the role of the deposition technique in the reactivity of the oxide.}, language = {en} } @misc{MoralesKostoTschammeretal., author = {Morales, Carlos and Kosto, Yuliia and Tschammer, Rudi and Henkel, Karsten and Flege, Jan Ingo}, title = {Unraveling the effects of substrate interaction on the chemical properties of atomic layer deposited ultra-thin ceria layers}, series = {Verhandlungen der DPG}, journal = {Verhandlungen der DPG}, publisher = {Deutsche Physikalische Gesellschaft}, address = {Bad Honnef}, issn = {0420-0195}, abstract = {Atomic layer deposition (ALD) is well known to lead to amorphous and defective, non-stoichiometric films, potentially resulting in modified material properties that can also be affected by film/substrate interaction in the case of ultra-thin growths. For example, the formation, diffusion, and recovery of oxygen vacancies can be favored in disordered, reducible metal oxides compared to more ordered deposits, whereas interdiffusion processes can critically affect the film/substrate interface region. These effects have extensively been studied for thin thermal-ALD ceria films (below 15 nm) by combining in-situ and ex-situ characterization techniques in our lab and at synchrotron radiation facilities. While using alumina or silica substrates modifies the initial growth rate, Ce3+/Ce4+ ratio, and ceria morphology, the formation of different species at the interface affects its reactivity. Interestingly, the experiments have shown high reducibility of ALD-ceria ultrathin films on silica for very low hydrogen concentrations, even at room temperature, whereas for alumina substrates the formation of aluminates at the interface prevents further oxidation. Moreover, the comparison with more ordered films indicates a key role of the defective structure of ALD films in Ce3+/Ce4+ conversion.}, language = {en} } @misc{KotHenkelSchmeisser, author = {Kot, Małgorzata and Henkel, Karsten and Schmeißer, Dieter}, title = {Internal chemical potential in mixed covalent-ionic photosensitive systems}, series = {Journal of Vacuum Science \& Technology A}, volume = {43 (2025)}, journal = {Journal of Vacuum Science \& Technology A}, number = {1}, publisher = {American Vacuum Society}, issn = {0734-2101}, doi = {10.1116/6.0004179}, pages = {1 -- 9}, abstract = {The internal chemical potential Γ of mixed covalent-ionic systems represents the potential differences between the covalent and the ionic intrinsic defect states located within the ionic gap. It is the key parameter to control the carrier densities, the stability regimes, and the photosensitive properties of materials. In this work, we describe first the quantitative analysis of the carrier densities in dependence on the internal potential Nπ(Γ) based on the common features of the electronic structure of mixed covalent-ionic materials. Subsequently, this method is applied on two mixed covalent-ionic materials, i.e., formamidinium lead triiodide and gallium oxide, as representatives of the respective families of perovskites (halides) and transparent conducting oxide thin films. Based on this analysis, the carrier densities as well as the photosensitivity mechanisms and the related specific properties of these materials in dependence on their internal chemical potential are discussed.}, language = {en} } @misc{KostoTschammerMoralesetal., author = {Kosto, Yuliia and Tschammer, Rudi and Morales, Carlos and Henkel, Karsten and Flege, Jan Ingo and Ratzke, Markus and Fischer, Inga Anita and Costina, Ioan and Alvarado Chavarin, Carlos and Wenger, Christian}, title = {Rational design and development of room temperature hydrogen sensors compatible with CMOS technology: a necessary step for the coming renewable hydrogen economy}, series = {Proceedings of iCampus Conference Cottbus 2024}, journal = {Proceedings of iCampus Conference Cottbus 2024}, publisher = {AMA Service GmbH}, address = {Wunstorf}, isbn = {978-3-910600-00-3}, doi = {10.5162/iCCC2024/P21}, pages = {182 -- 185}, abstract = {The transition towards a new, renewable energy system based on green energy vectors, such as hydrogen, requires not only direct energy conversion and storage systems, but also the development of auxiliary components, such as highly sensitive hydrogen gas sensors integrated into mass devices that operate at ambient conditions. Despite the recent advances in nanostructured metal oxide thin films in terms of simple fabrication processes and compatibility with integrated circuits, high sensitivity, and short response/recovery times usually require the use of expensive noble metals or elevated tem-peratures (>250 ºC), which results in high power consumption and poor long-term stability. This article presents the first steps of the work on developing a novel resistive hydrogen gas sensor based on ultrathin cerium oxide films, compatible with complementary metal oxide semiconductor technology and capable of operating at room temperature. Here, we show a multidisciplinary bottom-up approach combining different work areas for the sensor development, such as sensor architecture, sensing mechanism and deposition strategy of the active layer, electrical contact design depending on the desired electrical output, and fast testing under controlled environments.}, language = {en} } @misc{MoralesPlateMarthetal., author = {Morales, Carlos and Plate, Paul and Marth, Ludwig and Naumann, Franziska and Kot, Małgorzata and Janowitz, Christoph and Kus, Peter and Z{\"o}llner, Marvin Hartwig and Wenger, Christian and Henkel, Karsten and Flege, Jan Ingo}, title = {Bottom-up design of a supercycle recipe for atomic layer deposition of tunable Indium Gallium Zinc Oxide thin films}, series = {ACS Applied Electronic Materials}, volume = {6}, journal = {ACS Applied Electronic Materials}, number = {8}, publisher = {American Chemical Society (ACS)}, issn = {2637-6113}, doi = {10.1021/acsaelm.4c00730}, pages = {5694 -- 5704}, abstract = {We present a successful bottom-up approach to design a generic plasma-enhanced atomic layer deposition (PEALD) supercycle recipe to grow high-quality indium gallium zinc oxide (IGZO) thin films with tunable composition at a relatively low temperature of 150 °C. In situ real-time ellipsometric characterization in combination with ex situ complementary techniques has been used to optimize the deposition process and quality of the films by identifying and solving growth challenges such as degree of oxidation, nucleation delays, or elemental composition. The developed supercycle approach enables facile control of the target composition by adapting the subcycle ratios within the supercycle process. Compared to other low-temperature deposition techniques resulting in amorphous films, our PEALD-IGZO process at 150 °C results in nearly amorphous, nanocrystalline films. The preparation of IGZO films at low temperature by a supercycle PEALD approach allows controlling the thickness, composition, and electrical properties while preventing thermally induced segregation.}, language = {en} } @misc{KostoMoralesDevietal., author = {Kosto, Yuliia and Morales, Carlos and Devi, Anjana and Henkel, Karsten and Flege, Jan Ingo}, title = {Activity of cerium oxide thin films prepared by atomic layer deposition using custom and commercial precursors}, series = {Verhandlungen der DPG}, journal = {Verhandlungen der DPG}, publisher = {Deutsche Physikalische Gesellschaft}, address = {Bad Honnef}, issn = {0420-0195}, abstract = {Atomic layer deposition (ALD) allows preparation of conformal coatings with possibility to control their thickness at the submonolayer level, making it a good tool for depositing active layers on 3D structures. Our group is working on cerium oxide-based materials for hydrogen detection, which is difficult at ambient conditions due to the low sensitivity and long response time of the sensors. The cerium oxide layers prepared by ALD contain a lot of defects and provide an opportunity to overcome these complications. Thickness and morphology of the oxide films play an important role in defining the Ce3+/Ce4+ ratio, as well as the interface with the used substrate. Here, we compare cerium oxide thin films deposited by ALD techniques on SiO2 and Al2O3 substrates. The results reveal that the interface to the substrate can considerably influence the reactivity of the cerium oxide toward hydrogen and oxygen. Preparation of the oxides using two different precursors (commercial Ce(thd)4 and custom Ce(dpdmg)3) has been demonstrated to affect the redox properties of the films, their reactivity, and the reversibility.}, language = {en} } @misc{KotKediaPlateetal., author = {Kot, Małgorzata and Kedia, Mayank and Plate, Paul and Marth, Ludwig and Henkel, Karsten and Flege, Jan Ingo}, title = {Application of plasma enhanced atomic layer deposition process of alumina on perovskite film boosts efficiency of solar cells}, series = {Verhandlungen der DPG}, journal = {Verhandlungen der DPG}, publisher = {Deutsche Physikalische Gesellschaft}, address = {Bad Honnef}, issn = {0420-0195}, abstract = {It is assumed that plasma-enhanced atomic layer deposition (PEALD) cannot be used to prepare thin films on sensitive organic-inorganic perovskites because the plasma destroys the perovskite film and thus deteriorates its photophysical properties. Here, we prove that using an appropriate geometry of the ALD system (SENTECH SI PEALD system) and suitable process parameters it is possible to coat perovskites with alumina by PEALD. Spectromicroscopy followed by electrical characterisation reveal that as long as the PEALD process is not optimized (too long plasma pulses) one gets degradation of the perovskite as well as dissociation of the created iodine pentoxide (during PEALD) under light that causes a valence band maximum (VBM) shift to the Fermi level and thus significantly decreases the solar cell efficiency. However, once the PEALD process parameters are optimized, no VBM shift is observed. Moreover, the solar cell efficiency depends inversely on process temperature and layer thickness.}, language = {en} } @misc{MahmoodinezhadMoralesKotetal., author = {Mahmoodinezhad, Ali and Morales, Carlos and Kot, Małgorzata and Naumann, Franziska and Plate, Paul and Henkel, Karsten and Flege, Jan Ingo}, title = {A super-cycle approach to atomic layer deposition of indium-gallium-zinc oxide at low temperature}, series = {Verhandlungen der DPG}, journal = {Verhandlungen der DPG}, publisher = {Deutsche Physikalische Gesellschaft}, address = {Bad Honnef}, issn = {0420-0195}, abstract = {The continuing development of multifunctional devices needs novel multicomponent oxide layers, demanding a high control of both composition and thickness during their preparation. To this end, single metal oxides exhibiting high structural quality and conformity have successfully been grown by atomic layer deposition (ALD). However, the deposition of more complex compounds with specific optical and electrical properties is still challenging. In this work, we follow a bottom-up approach to design an ALD super-cycle to grow mixed indium-gallium-zinc oxide (IGZO) films with a controllable composition. For the formation of the individual indium, gallium, and zinc oxides, we found the use of plasma-enhanced ALD (PEALD) at 150 °C to be favorable when using the organometallic precursors trimethylindium, trimethylgallium, and diethylzinc together with oxygen plasma. The PEALD approach of IGZO films can particularly overcome a nucleation delay within the ZnO sub-cycle known from thermal ALD, achieving a higher growth per cycle and improving the quality and composition homogeneity of the films as shown by in-situ spectroscopic ellipsometry and ex-situ X-ray photoelectron spectroscopy.}, language = {en} } @misc{MoralesKostoTschammeretal., author = {Morales, Carlos and Kosto, Yuliia and Tschammer, Rudi and Henkel, Karsten and Flege, Jan Ingo}, title = {Reduction by H2 exposure at room temperature of ceria ultrathin films grown by atomic layer deposition}, series = {Verhandlungen der DPG}, journal = {Verhandlungen der DPG}, publisher = {Deutsche Physikalische Gesellschaft}, address = {Bad Honnef}, issn = {0420-0195}, abstract = {Atomic layer deposition (ALD) exhibits a high potential for integration as a scalable process in microelectronics, allowing well-controlled layer-by-layer deposition and conformal growth on 3D structures. Yet, the ALD technique is also well known to lead to amorphous and defective, non-stoichiometric films, potentially resulting in modified materials properties that, in the case of ultra-thin deposits, can also be affected by film/substrate interaction. Interestingly, initial in situ X-ray photoemission spectroscopy (XPS) measurements of ceria ALD-deposits on Al2O3/Si, sapphire, and SiO2 substrates confirm a Ce3+/Ce4+ mixture dependent on the substrate interaction, deposit thickness, and morphology. Using near-ambient pressure XPS, we have significantly reduced ultrathin (< 10 nm) ceria films grown by ALD by exposing them to different O2/H2 partial pressures at moderate temperatures (< 525K). Notably, the total amount of reduction to Ce3+ is found to depend on the deposit thickness and initial ceria/substrate interaction. Furthermore, the intrinsic defects related to the ALD method seem to play a critical role in the reversible reduction at room temperature.}, language = {en} } @misc{SchmeisserMuellerHenkel, author = {Schmeißer, Dieter and M{\"u}ller, Klaus and Henkel, Karsten}, title = {Photosensitive and Rectifying Properties of Ga2O3 Described by Polaronic Screened Electrons and Internal Potentials}, series = {Journal of Physical Chemistry C}, volume = {127}, journal = {Journal of Physical Chemistry C}, number = {47}, issn = {1932-7447}, doi = {10.1021/acs.jpcc.3c05785}, pages = {23077 -- 23089}, abstract = {The photosensitive and rectifying properties of Ga2O3 are described by (n-type) intrinsic (π-) electrons. These polaronic screened multiatomic carriers populate the intrinsic defect states within the ionic gap; their spectroscopic evidence is based on resonant photoemission spectroscopy data that also provide the ionicity factor of Ga2O3 and the size of the ionic gap. The π-electron density depends on the internal potential and its photo- and field-induced dipole contributions, and it describes the observed combined ohmic-exponential carrier densities and current-voltage dependences. The π-electron dynamics is caused by pairing and dissociation dipoles in the bulk of Ga2O3. The material properties of the electrode contribute via external chemical potentials and define the criteria for ohmic and rectifying contacts. This quantitative and predictive concept not only convinces by perfect agreement with published experimental data but also points toward the achievable performance limits of UV absorbers and rectifying devices.}, language = {en} } @misc{MoralesMahmoodinezhadTschammeretal., author = {Morales, Carlos and Mahmoodinezhad, Ali and Tschammer, Rudi and Kosto, Yuliia and Alvarado Chavarin, Carlos and Schubert, Markus Andreas and Wenger, Christian and Henkel, Karsten and Flege, Jan Ingo}, title = {Combination of Multiple Operando and In-Situ Characterization Techniques in a Single Cluster System for Atomic Layer Deposition: Unraveling the Early Stages of Growth of Ultrathin Al2O3 Films on Metallic Ti Substrates}, series = {Inorganics}, volume = {11}, journal = {Inorganics}, number = {12}, issn = {2304-6740}, doi = {10.3390/inorganics11120477}, abstract = {This work presents a new ultra-high vacuum cluster tool to perform systematic studies of the early growth stages of atomic layer deposited (ALD) ultrathin films following a surface science approach. By combining operando (spectroscopic ellipsometry and quadrupole mass spectrometry) and in situ (X-ray photoelectron spectroscopy) characterization techniques, the cluster allows us to follow the evolution of substrate, film, and reaction intermediates as a function of the total number of ALD cycles, as well as perform a constant diagnosis and evaluation of the ALD process, detecting possible malfunctions that could affect the growth, reproducibility, and conclusions derived from data analysis. The homemade ALD reactor allows the use of multiple precursors and oxidants and its operation under pump and flow-type modes. To illustrate our experimental approach, we revisit the well-known thermal ALD growth of Al2O3 using trimethylaluminum and water. We deeply discuss the role of the metallic Ti thin film substrate at room temperature and 200 °C, highlighting the differences between the heterodeposition (<10 cycles) and the homodeposition (>10 cycles) growth regimes at both conditions. This surface science approach will benefit our understanding of the ALD process, paving the way toward more efficient and controllable manufacturing processes.}, language = {en} } @misc{KotGawlińska‐NęcekHenkeletal., author = {Kot, Małgorzata and Gawlińska-Nęcek, Katarzyna and Henkel, Karsten and Flege, Jan Ingo}, title = {Prospects of improving efficiency and stability of hybrid perovskite solar cells by alumina ultrathin films}, series = {Small}, volume = {21}, journal = {Small}, number = {12}, publisher = {Wiley}, issn = {1613-6810}, doi = {10.1002/smll.202408435}, pages = {19}, abstract = {Over the last few years, the influence of low temperature (≤80 °C) and, in particular, of room temperature, atomic layer deposited alumina (ALD-Al2O3) on the properties of the underlying hybrid perovskites of different compositions and on the efficiency and stability of the corresponding perovskite solar cells (PSCs) is extensively investigated. The main conclusion is that most probably thanks to the presence of intrinsic defect states in the ALD-Al2O3 and in the perovskite layers, charge transfer and neutralization are possible and the entire lifetime of the PSCs is thus improved. Moreover, the migration of mobile ions between the layers is blocked by the ALD-Al2O3 layer and thus the occurrence of hysteresis in the current density-voltage characteristics of the PSCs is suppressed. Considering the uniform and nondestructive surface coverage, low thermal budget, small amount of material required, and short duration of the established ALD-Al2O3 deposition on top of hybrid perovskites, this additional, but fully solar cell technology-compatible, process step is most likely the most effective, cheapest, and fastest way to improve the efficiency and long-term stability of PSCs and thus increase their marketability.}, language = {en} } @misc{KotGawlińska‐NęcekPożarowskaetal., author = {Kot, Małgorzata and Gawlińska-Nęcek, Katarzyna and Pożarowska, Emilia and Henkel, Karsten and Schmeißer, Dieter}, title = {Photosensitivity and carrier densities of perovskite solar absorbers}, series = {Advanced science}, volume = {12}, journal = {Advanced science}, number = {16}, publisher = {Wiley}, address = {Hobken, New Jersey}, issn = {2198-3844}, doi = {10.1002/advs.202412711}, pages = {1 -- 8}, abstract = {Dark and light current-voltage characteristics of perovskite solar absorbers are analyzed in terms of their carrier densities. The analysis reveals p-type large polarons as a dominant carrier type in the investigated perovskite solar cells. The mechanism causing photosensitivity is attributed to the dissociation (and pairing) of bipolarons to large polarons (and vice versa) that are controlled by the internal potential Γ. As an example, the polaron concept is tested for a formamidinium lead triiodide perovskite solar cell. The individual steps of the data analysis are demonstrated and determine the ionicity factor of this perovskite film, quantify the density of the large polarons, and predict the gain and loss of photo-induced carriers. It is deduced that a reversible light-on/off operation can only occur when the bias voltage never exceeds a critical value of the internal potential. The results gained in this study suggest that the novel analysis can be successively applied on different hybrid perovskite materials, too.}, language = {en} } @misc{MoralesGertigKotetal., author = {Morales, Carlos and Gertig, Max and Kot, Małgorzata and Alvarado, Carlos and Schubert, Markus Andreas and Zoellner, Marvin Hartwig and Wenger, Christian and Henkel, Karsten and Flege, Jan Ingo}, title = {In situ X-ray photoelectron spectroscopy study of atomic layer deposited cerium oxide on SiO₂ : substrate influence on the reaction mechanism during the early stages of growth}, series = {Advanced materials interfaces}, volume = {12}, journal = {Advanced materials interfaces}, number = {5}, publisher = {Wiley}, address = {Weinheim}, issn = {2196-7350}, doi = {10.1002/admi.202400537}, pages = {1 -- 13}, abstract = {Thermal atomic layer deposition (ALD) of cerium oxide using commercial Ce(thd)4 precursor and O3 on SiO2 substrates is studied employing in-situ X-ray photoelectron spectroscopy (XPS). The system presents a complex growth behavior determined by the change in the reaction mechanism when the precursor interacts with the substrate or the cerium oxide surface. During the first growth stage, non-ALD side reactions promoted by the substrate affect the growth per cycle, the amount of carbon residue on the surface, and the oxidation degree of cerium oxide. On the contrary, the second growth stage is characterized by a constant growth per cycle in good agreement with the literature, low carbon residues, and almost fully oxidized cerium oxide films. This distinction between two growth regimes is not unique to the CeOx/SiO2 system but can be generalized to other metal oxide substrates. Furthermore, the film growth deviates from the ideal layer-by-layer mode, forming micrometric inhomogeneous and defective flakes that eventually coalesce for deposit thicknesses above 10 nm. The ALD-cerium oxide films present less order and a higher density of defects than films grown by physical vapor deposition techniques, likely affecting their reactivity in oxidizing and reducing conditions.}, language = {en} } @misc{MoralesTschammerPożarowskaetal., author = {Morales, Carlos and Tschammer, Rudi and Pożarowska, Emilia and Kosto, Julia and Villar-Garcia, Ignacio J. and P{\´e}rez-Dieste, Virginia and Favaro, Marco and Starr, David E. and Kapuścik, Paulina and Mazur, Michał and Wojcieszak, Damian and Domaradzki, Jarosław and Alvarado, Carlos and Wenger, Christian and Henkel, Karsten and Flege, Jan Ingo}, title = {Hydrogen sensing via heterolytic H₂ activation at room temperature by atomic layer deposited ceria}, series = {ChemSusChem : chemistry, sustainability, energy, materials}, volume = {18}, journal = {ChemSusChem : chemistry, sustainability, energy, materials}, number = {13}, publisher = {Wiley-VCH}, address = {Weinheim}, issn = {1864-5631}, doi = {10.1002/cssc.202402342}, pages = {1 -- 13}, abstract = {Ultrathin atomic layer deposited ceria films (\<20 nm) are capable of H2 heterolytic activation at room temperature, undergoing a significant reduction regardless of the absolute pressure, as measured under in-situ conditions by near ambient pressure X-ray photoelectron spectroscopy. ALD-ceria can gradually reduce as a function of H2 concentration under H2/O2 environments, especially for diluted mixtures below 10 \%. At room temperature, this reduction is limited to the surface region, where the hydroxylation of the ceria surface induces a charge transfer towards the ceria matrix, reducing Ce4+ cations to Ce3+. Thus, ALD-ceria replicates the expected sensing mechanism of metal oxides at low temperatures without using any noble metal decorating the oxide surface to enhance H2 dissociation. The intrinsic defects of the ALD deposit seem to play a crucial role since the post-annealing process capable of healing these defects leads to decreased film reactivity. The sensing behavior was successfully demonstrated in sensor test structures by resistance changes towards low concentrations of H2 at low operating temperatures without using noble metals. These promising results call for combining ALD-ceria with more conductive metal oxides, taking advantage of the charge transfer at the interface and thus modifying the depletion layer formed at the heterojunction.}, language = {en} }