@misc{GomezAlvarezMoralesMendezetal., author = {Gomez-Alvarez, Miguel Angel and Morales, Carlos and M{\´e}ndez, Javier and Campo, Adolfo del and Urbanos, Fernando J. and D{\´i}az, Aar{\´o}n and Res{\´e}ndiz, Luis and Flege, Jan Ingo and Granados, Daniel and Soriano, Leonardo}, title = {A Comparative Study of the ZnO Growth on Graphene and Graphene Oxide: The Role of the Initial Oxidation State of Carbon}, series = {C - Journal of Carbon Research}, volume = {6}, journal = {C - Journal of Carbon Research}, number = {2}, issn = {2311-5629}, doi = {10.3390/c6020041}, pages = {18}, abstract = {The role of the oxidation state of carbon on the early stages of growth of metal oxides was studied for the particular case of ZnO deposition on graphene and graphene oxide on SiO2 (G/SiO2 and GO/SiO2, respectively) substrates. The growth was carried out by thermal evaporation of metallic Zn under an oxygen atmosphere at room temperature. This technique permits quasi-equilibrium conditions during the oxide growth, allowing the characterization of the fundamental interaction between ZnO and the graphene-based substrates. Although in both cases ZnO follows a Volmer-Weber growth mode controlled by nucleation at defects, the details are different. In the case of the GO/SiO2 substrate, the nucleation process acts as a bottleneck, limiting the coverage of the complete surface and allowing the growth of very large ZnO structures in comparison to G/SiO2. Moreover, by studying the Zn-LMM Auger spectra, it is shown how the initial nature of the substrate influences the composition of the ZnO deposit during the very early stages of growth in terms of Zn/O atomic ratio. These results are compared to those previously reported regarding ZnO growth on graphite and graphene on Cu (G/Cu). This comparison allows us to understand the role of different characteristics of graphene-based substrates in terms of number of defects, oxidation state, graphene support substrate and number of graphene layers.}, language = {en} } @misc{MoralesLeinenFloresetal., author = {Morales, Carlos and Leinen, Dietmar and Flores, Eduardo and Mu{\~n}oz-Cortes, Esmeralda and Leardini, Fabrice and Ares, Jos{\´e} Ram{\´o}n and Flege, Jan Ingo and Soriano, Leonardo and Ferrer, Isabel J. and Sanchez, Carlos}, title = {Imaging the Kirkendall effect in pyrite (FeS2) thin films: Cross-sectional microstructure and chemical features}, series = {Acta Materialia}, volume = {205}, journal = {Acta Materialia}, issn = {1359-6454}, doi = {10.1016/j.actamat.2020.116582}, pages = {12}, abstract = {This investigation provides novel data on the structure and chemical composition of pyrite thin films and new hints concerning their formation mechanism. From TEM-HAADF data, it has been found that the films are composed of two different layers: one is very compact and the other one is quite porous with many voids separating a few groups of grains. This porous layer is always in direct contact with the substrate, and its thickness is quite similar to that of the original Fe film. The average size of pyrite grains is equal in both layers, what suggests that the same process is responsible for their formation. Concentration profiles of sulfur, iron and some impurities (mainly sodium and oxygen from the glass substrate) through both layers are given in this work, and thus chemical inhomogeneities of the films are proved by the obtained stoichiometric ratios (S/Fe). Moreover, Na from sodalime glass substrates mainly accumulates at the pyrite grain boundaries and barely dopes them. The obtained results support the hypothesis that the iron sulfuration process essentially induces the diffusion of iron atoms, what leads to the porous layer formation as a manifestation of the Kirkendall Effect. Therefore, it seems that the same mechanisms that operate in the synthesis of surface hollow structures at the nanoscale are also active in the formation of pyrite thin films ranging from several tens to hundreds of nanometers.}, language = {en} } @misc{MahmoodinezhadMoralesNaumannetal., author = {Mahmoodinezhad, Ali and Morales, Carlos and Naumann, Franziska and Plate, Paul and Meyer, Robert and Janowitz, Christoph and Henkel, Karsten and Kot, Małgorzata and Flege, Jan Ingo}, title = {Low-temperature atomic layer deposition of indium oxide thin films using trimethylindium and oxygen plasma}, series = {Verhandlungen der DPG - SurfaceScience21}, volume = {2021}, journal = {Verhandlungen der DPG - SurfaceScience21}, publisher = {Deutsche Physikalische Gesellschaft e.V.}, address = {Bad Honnef}, abstract = {Indium oxide thin films were deposited on Si (100) by plasma-enhanced atomic layer deposition (PEALD) using trimethylindium (TMIn) and oxygen plasma (O2) in a low-temperature range of 80 to 200 °C. The In2O3 layers were characterized by in-situ spectroscopic ellipsometry (SE), ex-situ X-ray photoelectron spectroscopy (XPS) and electrical measurements. The SE data show a growth rate of 0.56 {\AA}/cycle within the ALD window (100 to 150 °C) with a thickness inhomogeneity of ≤1.2\%. In addition, the highest refractive index is 2.07 (at 632.8 nm) for the layer grown at 150 °C, and the films exhibit indirect and direct band gaps of 2.8±0.1 eV and 3.3±0.2 eV, respectively. XPS characterization indicates no carbon incorporation and a temperature-dependent off-stoichiometry of the layers. The chemical analysis of the In 3d and O 1s core levels confirms the formation of In-O bonds and suggests the additional presence of hydroxyl groups and defects. With increasing temperature, the contribution of OH groups and defects decreases whereas that of In-O bonds increases. Notably, higher growth temperatures result in an indium rich phase within the layers.}, language = {en} } @misc{MoralesMahmoodinezhadSchubertetal., author = {Morales, Carlos and Mahmoodinezhad, Ali and Schubert, Andreas Markus and Wenger, Christian and Henkel, Karsten and Flege, Jan Ingo}, title = {Functional ultra-thin oxide films deposited by atomic layer deposition on structured substrates}, series = {Verhandlungen der DPG - SurfaceScience21}, volume = {2021}, journal = {Verhandlungen der DPG - SurfaceScience21}, publisher = {Deutsche Physikalische Gesellschaft e.V.}, address = {Bad Honnef}, abstract = {In the last decades, atomic layer deposition (ALD) has gained prominence in the materials and surface science communities owing to its high potential for integration as a scalable process in microelectronics. ALD's largest strengths are its well-controlled layer-by-layer deposition and growth conformity on 3D structures. Yet, the ALD technique is also well known to lead to amorphous and defective, non-stoichiometric thin films, resulting in modified materials properties that may even preferentially be used in certain applications. To study these issues, we have developed an in-situ ALD reactor attached to an X-ray photoelectron spectroscopy (XPS) system, capable of switching between both pump and flow-type operation. This novel tool allows to cover the entire range of compounds and recipes used in ALD, thus clarifying the role of such defects at different deposition stages, growth conditions and film/substrate interfaces. To exemplify these sorts of studies, we show the deposition of Al2O3 5-10 nm films on nanostructured Si, and their use as substrates for functional CeOx ALD deposits.}, language = {en} } @misc{PozarowskaMoralesFlege, author = {Pozarowska, Emilia and Morales, Carlos and Flege, Jan Ingo}, title = {Growth of samarium thin films and subsequent oxidation on polycrystalline copper}, series = {Verhandlungen der DPG - SurfaceScience21}, volume = {2021}, journal = {Verhandlungen der DPG - SurfaceScience21}, publisher = {Deutsche Physikalische Gesellschaft e.V.}, address = {Bad Honnef}, abstract = {The growth of samaria thin films on copper sheets has been chemically studied by in situ X-ray photoelectron spectroscopy (XPS). The early stages of growth (0.1-14 ML) were studied by consecutive evaporations of Sm by chemical vapor deposition followed by XPS measurements. Subsequently, samaria films of different thicknesses, namely 0.1, 1, and 14 ML, were oxidized at room temperature (RT). The evolution of the sample morphology was determined through inelastic peak shape analysis (IPSA) using the QUASES software as an indirect method to study the relationship between Sm oxidation state and its surface arrangement. Our results show that samarium grows as 2D islands up to 2ML, which is followed by 3D growth. Chemical analysis indicates that at low coverages (<0.5ML) Sm is already oxidized, leading to the appearance of Sm3+ as the only oxidation state. The increase in the intensity of the O1s peak with time and the absence of spectral changes in the Cu2p and LMM Auger (substrate) indicate that the transformation is mainly due to adventitious oxidation of the layer. With further deposition at RT the metallic state Sm0 appears at higher coverages, which is readily postoxidized by subsequent exposure to molecular oxygen, leading to complete oxidation. No intermediate oxidation states (Sm2+) were observed, in contrast to the reported prevalence of Sm2+ on single crystal surfaces during the early stages of growth.}, language = {en} } @misc{MoralesLeinenCampoetal., author = {Morales, Carlos and Leinen, Dietmar and Campo, Adolfo del and Ares, Jos{\´e} Ram{\´o}n and S{\´a}nchez, Carlos and Flege, Jan Ingo and Guti{\´e}rrez, Alejandro and Prieto, Pilar and Soriano, Leonardo}, title = {Growth and characterization of ZnO thin films at low temperatures: from room temperature to -120 °C}, series = {Journal of Alloys and Compounds}, volume = {884}, journal = {Journal of Alloys and Compounds}, issn = {0925-8388}, doi = {10.1016/j.jallcom.2021.161056}, abstract = {ZnO thin films have been grown by e-beam evaporation in the range from room temperature to - 120 °C on two types of substrates, Al2O3 (0001) and Si (100). Although the ZnO/Al2O3 system has been thoroughly characterized, including optical and electrical techniques, the morphological, structural and chemical properties show no significant differences between both substrates. Thus, the general features of the ZnO growth mode at low temperature can be generalized. The relatively low growth temperatures reduce the diffusion of atoms at the surface, which leads to morphological and chemical changes. As the temperature decreases, the growth mode changes from a van der Drift model to a gradual bilayer system composed of an interfacial layer in contact with the substrate and a second columnar-based layer. This second well-ordered film disappears for the lowest temperatures while a Zn-rich interface in contact with the substrate emerges. Precisely from this interface, Zn-rich whiskers develop under the ZnO film and cause the loss of adhesion at temperatures below - 100 °C. These extreme temperatures also affect the crystal size, lattice strain, and total amount of oxygen vacancies. The behavior of the optical and electrical properties in terms of band gap, transparency, electrical resistivity, and Seebeck coefficient is discussed in the light of structural and chemical characterization. Samples grown at 0 °C exhibit an enhanced transmittance compared to those grown at room temperature while preserving similar electrical resistivity values and natural n-type doping. These results open a promising route to enhance ZnO films properties below the typical high temperature window.}, language = {en} } @misc{MahmoodinezhadMoralesNaumannetal., author = {Mahmoodinezhad, Ali and Morales, Carlos and Naumann, Franziska and Plate, Paul and Meyer, Robert and Janowitz, Christoph and Henkel, Karsten and Kot, Małgorzata and Z{\"o}llner, Marvin Hartwig and Wenger, Christian and Flege, Jan Ingo}, title = {Low-temperature atomic layer deposition of indium oxide thin films using trimethylindium and oxygen plasma}, series = {Journal of Vacuum Science and Technology A}, volume = {39}, journal = {Journal of Vacuum Science and Technology A}, number = {6}, issn = {0734-2101}, doi = {10.1116/6.0001375}, abstract = {Indium oxide (InxOy) thin films were deposited by plasma-enhanced atomic layer deposition (PEALD) using trimethylindium and oxygen plasma in a low-temperature range of 80-200 °C. The optical properties, chemical composition, crystallographic structure, and electrical characteristics of these layers were investigated by spectroscopic ellipsometry (SE), x-ray photoelectron spectroscopy (XPS), x-ray diffraction (XRD), as well as current-voltage and capacitance-voltage measurements. The SE results yielded a nearly constant growth rate of 0.56 {\AA} per cycle and a thickness inhomogeneity of ≤1.2\% across 4-in. substrates in the temperature range of 100-150 °C. The refractive index (at 632.8 nm) was found to be 2.07 for the films deposited at 150 °C. The PEALD-InxOy layers exhibit a direct (3.3 ± 0.2 eV) and an indirect (2.8 ± 0.1 eV) bandgap with an uptrend for both with increasing substrate temperature. Based on XPS characterization, all InxOy samples are free of carbon impurities and show a temperature-dependent off-stoichiometry indicating oxygen vacancies. XRD diffraction patterns demonstrate an onset of crystallization at 150 °C. Consistent with the optical, XPS, and XRD data, the films deposited at ≥150 °C possess higher electrical conductivity. Our findings prove that a low-temperature PEALD process of InxOy is feasible and promising for a high-quality thin-film deposition without chemical impurities on thermally fragile substrates.}, language = {en} } @misc{GonzalezJuarezMoralesFlegeetal., author = {Gonzalez-Juarez, Maria de Lourdes and Morales, Carlos and Flege, Jan Ingo and Flores, Eduardo and Martin-Gonzalez, Marisol and Nandhakumar, Iris and Bradshaw, Darren}, title = {Tunable Carrier Type of a Semiconducting 2D Metal-Organic Framework Cu3(HHTP)2}, series = {ACS Applied Materials \& Interfaces}, volume = {14}, journal = {ACS Applied Materials \& Interfaces}, number = {10}, issn = {1944-8244}, doi = {10.1021/acsami.2c00089}, pages = {12404 -- 12411}, abstract = {In this work, a switch from n-type to p-type conductivity in electrodeposited Cu3(2,3,6,7,10,11-hexahydroxytriphenylene)2 [Cu3(HHTP2)] has been observed, which is most likely due to oxygen molecular doping. The synthesis of electrically conductive 2D metal-organic frameworks (MOFs) has been achieved through the introduction of highly conjugated organic linkers coordinated to their constituent metal-ion centers. However, the porous structure and unsaturated metal sites in MOFs make them susceptible to ambient adsorbates, which can affect their charge transport properties. This phenomenon has been experimentally investigated by GIXRD, Hall effect and Seebeck measurements, and X-ray photoelectron spectroscopy.}, language = {en} } @misc{JanowitzMahmoodinezhadKotetal., author = {Janowitz, Christoph and Mahmoodinezhad, Ali and Kot, Małgorzata and Morales, Carlos and Naumann, Franziska and Plate, Paul and Z{\"o}llner, Marvin Hartwig and B{\"a}rwolf, Florian and Stolarek, David and Wenger, Christian and Henkel, Karsten and Flege, Jan Ingo}, title = {Toward controlling the Al2O3/ZnO interface properties by in situ ALD preparation}, series = {Dalton Transactions}, volume = {51}, journal = {Dalton Transactions}, issn = {1477-9234}, doi = {10.1039/D1DT04008A}, pages = {9291 -- 9301}, abstract = {An Al2O3/ZnO heterojunction was grown on a Si single crystal substrate by subsequent thermal and plasma-assisted atomic layer deposition (ALD) in situ. The band offsets of the heterointerface were then studied by consecutive removal of the layers by argon sputtering, followed by in situ X-ray photoelectron spectroscopy. The valence band maximum and conduction band minimum of Al2O3 are found to be 1.1 eV below and 2.3 eV above those of ZnO, resulting in a type-I staggered heterojunction. An apparent reduction of ZnO to elemental Zn in the interface region was detected in the Zn 2p core level and Zn L3MM Auger spectra. This suggests an interface formation different from previous models. The reduction of ZnO to Zn in the interface region accompanied by the creation of oxygen vacancies in ZnO results in an upward band bending at the interface. Therefore, this study suggests that interfacial properties such as the band bending as well as the valence and conduction band offsets should be in situ controllable to a certain extent by careful selection of the process parameters.}, language = {en} } @misc{MoralesPascualLeinenetal., author = {Morales, Carlos and Pascual, Antonio and Leinen, Dietmar and Flores, Eduardo and Mu{\~n}oz-Cortes, Esmeralda and Leardini, Fabrice and Ares, Jos{\´e} Ram{\´o}n and Flege, Jan Ingo and Soriano, Leonardo and Ferrer, Isabel J. and Sanchez, Carlos}, title = {Reaction Mechanism and Kinetic Model of Fe Thin Film Transformation into Monosulfides (FeS): First Step of the Fe Films Sulfuration Process into Pyrite}, series = {The Journal of Physical Chemistry C}, volume = {126}, journal = {The Journal of Physical Chemistry C}, number = {32}, issn = {1932-7455}, doi = {10.1021/acs.jpcc.2c02060}, pages = {13870 -- 13883}, abstract = {The sulfuration of metallic iron layers into pyrite (FeS2) is preceded by an initial stage characterized by the iron transformation into monosulfide, which acts as a precursor of the disulfide. This work presents a comprehensive reaction and kinetic model of the sulfuration reaction of metallic iron thin films into monosulfides when a molecular sulfur (S2) atmosphere is used. By slowing down the sulfuration reaction, we have been able to follow in situ the evolution of the transport properties (electrical resistivity and Seebeck coefficient) of the Fe films during their sulfuration reaction to monosulfides. We show that two different stages characterize this initial sulfuration: (1) the transformation of Fe into hexagonal pyrrhotite (Fe → Fe1-xSH) and (2) a partial crystallographic transformation of this hexagonal pyrrhotite into orthorhombic pyrrhotite (Fe1-xSH → Fe1-xSO). A two-step process can explain the pyrrhotite hexagonal phase formation, being first controlled by the surface adsorption of S2 on the external sample interface (S2/pyrrhotite) and second by the diffusion of Fe atoms through the formed pyrrhotite layer. By deducing the corresponding kinetic equations in terms of the experimental parameters (S2 partial pressure and thicknesses of the layers of present species), we can explain the evolution of the electrical resistance and Seebeck coefficient of the original Fe film during its transformation into monosulfide. At the same time, the appearance of the Kirkendall effect during the monosulfide phase formation is experimental and formally justified. The comprehensive description of this first stage of the complete sulfuration process of the Fe film into pyrite provides a layout to deeply discuss the influence of these intermedium phases on the final iron disulfide film characteristics and the appearance of potential film defects related to the experimental growth conditions.}, language = {en} } @misc{PozarowskaPleinesPrietoetal., author = {Pozarowska, Emilia and Pleines, Linus and Prieto, Mauricio J. and Tănase, Liviu Christian and Souza Caldas, Lucas de and Tiwari, Aarti and Schmidt, Thomas and Falta, Jens and Morales, Carlos and Flege, Jan Ingo}, title = {The relation between structure sensitivity and doping of ceria(111) vs. ceria(100)}, series = {Verhandlungen der DPG}, journal = {Verhandlungen der DPG}, publisher = {Deutsche Physikalische Gesellschaft}, address = {Bad Honnef}, issn = {0420-0195}, abstract = {CeOx-Cu inverse catalysts have been shown to convert CO2 into valuable chemicals through catalytic hydrogenation. The catalytic activity may further be enhanced by alloying ceria with trivalent, catalytically active metals, such as Sm, promoting the formation of Ce3+ active sites. In this work, the structural and chemical properties of (111)- and (100)- oriented CeOx islands alloyed with samarium were explored by low-energy electron microscopy and X-ray photoemission electron microscopy. After Sm deposition on the as-grown CeOx islands, the near-surface region of (100)-oriented CeOx is reduced after exposure to H2 at 470 ∘C, whereas the deeper layers as well as the whole (111)-oriented islands retain the Ce4+ state. Subsequent reoxidation with O2 leads to the complete Ce4+ state recovery, suggesting the healing of oxygen vacancies. Additional annealing at 470 ∘C induces samarium diffusion into the ceria matrix. Yet, subsequent exposure to H2 reduces neither the (111)- nor the (100)-oriented CeSmOx islands, suggesting a quite unexpected stability of this system.}, language = {en} }