@inproceedings{ChoudhuryTallaridaDasetal., author = {Choudhury, Sakeb Hasan and Tallarida, Massimo and Das, Chittaranjan and Schmeißer, Dieter}, title = {Atomic layer deposition of Ga2O3 using Tri-methyl-Gallium and H2O}, series = {Verhandlungen der Deutschen Physikalischen Gesellschaft}, booktitle = {Verhandlungen der Deutschen Physikalischen Gesellschaft}, publisher = {Deutsche Physikalische Gesellschaft}, address = {Bad Honnef}, abstract = {Considering numerous applications such as transparent conducting oxides, gas sensors, photovoltaic applications, deep UV photo detectors, field effect transistors and spintronics gallium oxide (Ga2O3) has earned quite a lot of focus recently. Various techniques have already been demonstrated to produce Ga2O3 naming evaporation, sputtering, pulsed laser deposition, chemical vapor deposition and atomic layer deposition (ALD). Among them, ALD gives the possibility of controlling the thickness at the atomic level, good step coverage and delivers dense and homogeneous films. In this contribution, we report on the growth of ALD Ga2O3 using trimethylgallium (TMG) and H2O as metal and oxygen precursors, respectively. We deposited thin Ga2O3 films on Si, TiO2, Al2O3 and RuO2 over a temperature range of 150-300°C and characterized them by X-ray photo emission spectroscopy and atomic force microscopy. From this study, we are able to discuss the influence of the temperature on the growth dynamics of Ga2O3 and its chemical composition.}, language = {en} } @inproceedings{DasTallaridaSkorupskaetal., author = {Das, Chittaranjan and Tallarida, Massimo and Skorupska, Katarzyna and Lewerenz, Hans-Joachim and Schmeißer, Dieter}, title = {An efficient Si photo cathode for a wide range of electrolyte pH values}, series = {Verhandlungen der Deutschen Physikalischen Gesellschaft}, booktitle = {Verhandlungen der Deutschen Physikalischen Gesellschaft}, publisher = {Deutsche Physikalische Gesellschaft}, address = {Bad Honnef}, abstract = {Hydrogen fuel cells, being environmental friendly to produce energy, are a technology of future. One of the efficient ways to produce hydrogen is solar driven photocatalysis using semiconducting materials as photo electrodes. The choice of electrodes is a crucial factor and is done on the basis of photo corrosion stability, light absorption efficiency, and photocarrier lifetime. P-type Si can be used as photo cathode to produce H2 by direct photocatalysis. Si cathodes can be used in acidic electrolytes to have efficient photo catalytic activity but they are unstable in alkaline electrolytes. Therefore, to use both Si electrodes in the same electrolyte, their chemical stability should be extended over a wide range of pH. To this purpose we modified the surface of a p-type Si photocathode with very thin films of TiO2 grown by atomic layer deposition (ALD). We found that the modified Si cathode shows an increased photoresponse and a lower onset potential with respect to the pristine surface and an increased stability at various pH values.}, language = {en} } @misc{SowinskaDasWojciechowskietal., author = {Sowinska, Małgorzata and Das, Chittaranjan and Wojciechowski, Konrad and Rouissi, Zied and Snaith, Henry J. and Schmeißer, Dieter}, title = {Atomic layer deposition of Al2O3 on CH3NH3PbI3 for enhancement of perovskite solar cells stability}, series = {Synchrotron Radiation in Natural Science : Bulletin of the Polish Synchrotron Radiation Society}, volume = {15}, journal = {Synchrotron Radiation in Natural Science : Bulletin of the Polish Synchrotron Radiation Society}, number = {1-2}, issn = {1644-7190}, pages = {S. 33}, language = {en} } @inproceedings{DasTallaridaSchmeisser, author = {Das, Chittaranjan and Tallarida, Massimo and Schmeißer, Dieter}, title = {TiO2 laminated Silicon microstructures based stable photocathode for water splitting}, series = {Verhandlungen der Deutschen Physikalischen Gesellschaft}, booktitle = {Verhandlungen der Deutschen Physikalischen Gesellschaft}, publisher = {Deutsche Physikalische Gesellschaft}, address = {Bad Honnef}, pages = {S. 213}, abstract = {The photoelectrochemical (PEC) water splitting is one of the most efficient ways to obtain hydrogen from water using solar power which can be used as carbon free fuel. The PEC device can bedesigned using semiconducting material that will convert solar radiation to H2. Silicon can be one of the best choices for PEC due to its success in solar cells technology. There are certain issues with Si such as stability in electrochemical medium [1] and higher surface reflectance (25\%) which limits the Si as an ideal candidate for PEC technique [2]. In the present work we addressed these issues by surface structuring and laminating the surface with metal oxide. The microstructuring of Si was done by electrochemical method. The Si microstructure photocathode was stabilized by thin layer of ALD grown TiO2 film. The microstructuring and lamination of Si photocathode by ALD layer of TiO2 decreased the reflectance ofthe surface and shift the onset potential towards anodic direction by 350 mV with a prolonged stability over 60 hours[3]. [1] C. Levy-Clement, J. Electrochem. Soc 1991, 12, 69 [2] J. Oh, et al. Energy Environ. Sci., 2011, 4, 1690 [3] C. Das, et al. Nanoscale 2015,7, 7726}, language = {en} } @misc{GhoshBiswasSenetal., author = {Ghosh, Sujoy Kumar and Biswas, Anirban and Sen, Shrabanee and Das, Chittaranjan and Henkel, Karsten and Schmeißer, Dieter and Mandal, Dipankar}, title = {Yb3+ Assisted Self-Polarized PVDF Based Ferroelectretic Nanogenerator: A Facile Strategy of Highly Efficient Mechanical Energy Harvester Fabrication}, series = {Nano Energy}, volume = {2016}, journal = {Nano Energy}, number = {30}, issn = {2211-2855}, doi = {10.1016/j.nanoen.2016.10.042}, pages = {621 -- 629}, abstract = {Ytterbium (Yb3+) assisted porous poly(vinylidene fluoride) (PVDF) composite film comprising flexible ferroelectretic nanogenerator (FTNG) is highlighted where traditional poling treatment is completely avoided. The piezoelectric output of FTNG is realized by the co-operative activity of self-polarized -CH2/-CF2 dipoles with porous electret-like structure in the composite film. Owing to extraordinary ferroelectric and dielectric properties, FTNG is acting as a highly efficient mechanical energy harvester. It is capable to capture several forms of abundant mechanical energy arising from humanfinger movements, machine vibrations and sound waves. As a proof of concept, under compressive deformation, FTNG is enable to instantly powers up several consumer electronics and thus provides a promising strategy for achieving self-powered electronic devices.}, language = {en} } @misc{KotDasWangetal., author = {Kot, Małgorzata and Das, Chittaranjan and Wang, Zhiping and Henkel, Karsten and Rouissi, Zied and Wojciechowski, Konrad and Snaith, Henry J. and Schmeißer, Dieter}, title = {Room-Temperature Atomic Layer Deposition of Al₂O₃: Impact on Efficiency, Stability and Surface Properties in Perovskite Solar Cells}, series = {ChemSusChem}, volume = {9}, journal = {ChemSusChem}, number = {24}, issn = {1864-5631}, doi = {10.1002/cssc.201601186}, pages = {3401 -- 3406}, abstract = {In this work, solar cells with a freshly made CH₃NH₃PbI₃ perovskite film showed a power conversion efficiency (PCE) of 15.4 \% whereas the one with 50 days aged perovskite film only 6.1 \%. However, when the aged perovskite was covered with a layer of Al₂O₃ deposited by atomic layer deposition (ALD) at room temperature (RT), the PCE value was clearly enhanced. X-ray photoelectron spectroscopy study showed that the ALD precursors are chemically active only at the perovskite surface and passivate it. Moreover, the RT-ALD-Al2O3-covered perovskite films showed enhanced ambient air stability.}, language = {en} } @misc{HenkelDasKotetal., author = {Henkel, Karsten and Das, Chittaranjan and Kot, Małgorzata and Schmeißer, Dieter and Naumann, Franziska and K{\"a}rkk{\"a}nen, Irina and Gargouri, Hassan}, title = {In-gap states in titanium dioxide and oxynitride atomic layer deposited films}, series = {Journal of Vacuum Science and Technology: A}, volume = {35}, journal = {Journal of Vacuum Science and Technology: A}, number = {1}, issn = {0734-2101}, doi = {10.1116/1.4972247}, pages = {01B135-1 -- 01B135-8}, abstract = {Valence band (VB) spectra of titanium dioxide (TiO2) and oxynitride (TiOxNy) films prepared by different atomic layer deposition (ALD) processes are compared and related to electrical characterization [current-voltage (JV) and capacitance-voltage (CV)] results. By increasing the nitrogen amount in the TiO2 film, band-gap narrowing is observed. The band-gap decrease is related to the contribution of the nitrogen density of states, which induces defects within the band-gap and thus reduces its optical band-gap. In-gap states are found in the VB spectra at 1 eV below the Fermi energy in all investigated ALD samples, i.e., in TiO2 as well as in TiOxNy films. An exponential correlation between leakage current density and in-gap state intensity is derived by the combination of JV measurements and VB spectra, whereas the in-gap states seem to have no influence on hysteresis and fixed oxide charges found in the CV data. It is argued that the in-gap states in TiO2 and TiOxNy have an excitonic or polaronic origin. Both, band-gap narrowing and in-gap state intensity can be tuned by the ALD process selection and the variation of its parameters.}, language = {en} } @misc{MenezesIndraDasetal., author = {Menezes, Prashanth W. and Indra, Arindam and Das, Chittaranjan and Walter, Carsten and G{\"o}bel, Caren and Gutkin, Vitaly and Schmeißer, Dieter and Driess, Matthias}, title = {Uncovering the Nature of Active Species of Nickel Phosphide Catalysts in High-Performance Electrochemical Overall Water Splitting}, series = {ACS Catalysis}, volume = {7}, journal = {ACS Catalysis}, number = {1}, issn = {2155-5435}, doi = {10.1021/acscatal.6b02666}, pages = {103 -- 109}, abstract = {A systematic structural elucidation of the near-surface active species of the two remarkably active nickel phosphides Ni12P5 and Ni2P on the basis of extensive analytical, microscopic, and spectroscopic investigations is reported. The latter can serve as complementary efficient electrocatalysts in the hydrogen (HER) versus oxygen evolution reaction (OER) in alkaline media. In the OER Ni12P5 shows enhanced performance over Ni2P due to the higher concentration of nickel in this phase, which enables the formation of an amorphous NiOOH/Ni(OH)2 shell on a modified multiphase with a disordered phosphide/phosphite core. The situation is completely reversed in the HER, where Ni2P displayed a significant improvement in electrocatalytic activity over Ni12P5 owing to a larger concentration of phosphide/phosphate species in the shell. Moreover, the efficiently combined use of the two nickel phosphide phases deposited on nickel foam in overall electrocatalytic water splitting is demonstrated by a strikingly low cell voltage and high stability with pronounced current density, and these catalysts could be an apt choice for applications in commercial alkaline water electrolysis.}, language = {en} } @misc{IndraMenezesDasetal., author = {Indra, Arindam and Menezes, Prashanth W. and Das, Chittaranjan and G{\"o}bel, Caren and Tallarida, Massimo and Schmeißer, Dieter and Driess, Matthias}, title = {A facile corrosion approach to the synthesis of highly active CoOxwater oxidation catalysts}, series = {Journal of Materials Chemistry A}, journal = {Journal of Materials Chemistry A}, number = {5}, issn = {2050-7488}, doi = {10.1039/c6ta10650a}, pages = {5171 -- 5177}, abstract = {Ultra-small rock salt cobalt monoxide (CoO) nanoparticles were synthesized and subjected to partial oxidation ('corrosion') with ceric ammonium nitrate (CAN) to form mixed-valence CoOx(1 < x< 2) water oxidation catalysts. Spectroscopic, microscopic and analytical methods evidenced a structural reformation of cubic CoO to active CoOx with a spinel structure. The superior water oxidation activity of CoOx has been established in electrochemical water oxidation under alkaline conditions. Electrochemical water oxidation with CoOx was recorded at a considerably low overpotential of merely 325 mV at a current density of 10 mA cm-2 in comparison to 370 mV for CoO. Transformation of both octahedral CoII and CoIII sites into amorphous Co(OH)2-CoOOH is the key to high electrochemical activity while the presence of a higher amount of octahedral CoIII sites in CoOx is imperative for an efficient oxygen evolution process.}, language = {en} } @misc{DasKotRouissietal., author = {Das, Chittaranjan and Kot, Małgorzata and Rouissi, Zied and Kędzierski, Kamil and Henkel, Karsten and Schmeißer, Dieter}, title = {Selective Deposition of an ultrathin Pt Layer on a Au-Nanoisland-Modified Si Photocathode for Hydrogen Generation}, series = {ACS Omega}, volume = {2}, journal = {ACS Omega}, number = {4}, issn = {2470-1343}, doi = {10.1021/acsomega.6b00374}, pages = {1360 -- 1366}, abstract = {Platinum, being the most efficient and stable catalyst, is used in photoelectrochemical (PEC) devices. However, a minimal amount of Pt with maximum catalytic activity is required to be used to minimize the cost of production. In this work, we use an environmentally friendly, ost-effective, and less Pt-consuming method to prepare PEC devices for the hydrogen evolution reaction (HER). The Pt monolayer catalyst is selectively deposited on a Au-nanoisland-supported boron-doped p-type Si (100) photocathode. The PEC device based on the Si photocathode with an ultralow loading of the Pt catalyst exhibits a comparable performance for the HER to that of devices with a thick Pt layer. In addition, we demonstrate that by using a thin TiO2 layer deposited by atomic layer deposition photo-oxidation of the Si photocathode can be blocked resulting in a stable PEC performance.}, language = {en} } @misc{KotHenkelDasetal., author = {Kot, Małgorzata and Henkel, Karsten and Das, Chittaranjan and Brizzi, Simone and K{\"a}rkk{\"a}nen, Irina and Schneidewind, Jessica and Naumann, Franziska and Gargouri, Hassan and Schmeißer, Dieter}, title = {Analysis of titanium species in titanium oxynitride films prepared by plasma enhanced atomic layer deposition}, series = {Surface and Coatings Technology}, volume = {324}, journal = {Surface and Coatings Technology}, issn = {0257-8972}, doi = {10.1016/j.surfcoat.2016.11.094}, pages = {586 -- 593}, abstract = {A comparative study of thin titanium oxynitride (TiOxNy) films prepared by plasma enhanced atomic layer deposition using tetrakis(dimethylamino)titanium (TDMAT) and N2 plasma as well as titanium(IV)isopropoxide and NH3 plasma is reported. The comparison is based on the combination of Ti2p core level and valence band spectroscopy and current-voltage measurements. The TDMAT/N2 process delivers generally higher fractions of TiN and TiON within the Ti2p spectra of the films and stronger photoemissions within the bandgap as resolved in detail by high energy resolution synchrotron-based spectroscopy. In particular, it is shown that higher TiN contributions and in-gap emission intensities correlate strongly with increased leakage currents within the films and might be modified by the process parameters and precursor selection.}, language = {en} }