@misc{MorozovaObrosovNaumovetal., author = {Morozova, Iuliia and Obrosov, Aleksei and Naumov, Anton and Kr{\´o}licka, Aleksandra and Golubev, Iurii and Bokov, Dmitry O. and Doynov, Nikolay and Weiß, Sabine and Michailov, Vesselin}, title = {Impact of Impulses on Microstructural Evolution and Mechanical Performance of Al-Mg-Si Alloy Joined by Impulse Friction Stir Welding}, series = {Materials}, volume = {14}, journal = {Materials}, number = {2}, issn = {1996-1944}, doi = {https://doi.org/10.3390/ma14020347}, abstract = {Impulse Friction Stir Welding (IFSW) was utilized to join 6082-T6 alloy plates at various impulse frequencies. A distinctive feature of IFSW is the generation of mechanical impulses that enhances the forging action of the tool, and thereby, alters the weld microstructure. The microstructural evolution in the Stir Zone (SZ) with special focus on the strengthening precipitation behavior, and overall mechanical properties of the IFSW joints have been investigated. It was demonstrated that the strengthening β″ precipitates reprecipitated in the SZ of the IFSW joints during natural aging. In contrast, no precipitates were found in the SZ of the Friction Stir Welding (FSW) weld. Partial reversion of β″ after IFSW is supposed to occur due to more developed subgrain network and higher dislocation density introduced by impulses that accelerated precipitation kinetics. Dynamic recrystallisation was facilitated by impulses resulting in a fine, homogeneous structure. There was no significant difference between the microhardness in the SZ, tensile and yield strength of the FSW and IFSW joints. However, the application of impulses demonstrated the smoothing of the hardness reduction in the transition region at the advancing side. The shift of the fracture location from the Heat-Affected Zone (HAZ) by FSW to the SZ as well as higher elongation of the joints by IFSW of lower frequencies could be related to the grain refinement and the change of the grain orientation.}, language = {en} } @misc{MorozovaKrolickaObrosovetal., author = {Morozova, Iuliia and Kr{\´o}licka, Aleksandra and Obrosov, Aleksei and Yang, Yitong and Doynov, Nikolay and Weiß, Sabine and Michailov, Vesselin}, title = {Precipitation phenomena in impulse friction stir welded 2024 aluminium alloy}, series = {Materials Science and Engineering: A}, journal = {Materials Science and Engineering: A}, issn = {0921-5093}, doi = {10.1016/j.msea.2022.143617}, pages = {1 -- 11}, abstract = {Microhardness variations across the friction stir welded (FSW) and impulse friction stir welded (IFSW) AA2024-T351 joints have been elucidated by the transformations of the S-Al2CuMg phase with a special focus on a distinguished hardness peak within the heat-affected zone (HAZ) of the impulse welds. The increase in hardness within the stir zone (SZ) originated from the partial re-precipitation of the initial Guinier-Preston-Bagaryatsky zones (GPB) and metastable S needles, previously dissolved.) Formation and growth of stable S precipitates via coalescence accounted for the softening through the thermo-mechanically affected zone (TMAZ). The peak strengthening within the HAZ of the IFSW joints was mainly caused by the dense needle-shaped S particles, which can be explained by a mutual influence of the process specific temperature and strain cycles. Dislocations and subgrain boundaries introduced to the material due to plastic deformation facilitated the nucleation of strengthening S precipitates in the HAZ. It demonstrates that the impact of deformation should be considered by the characterization of the precipitation development in the HAZ.}, language = {en} }